Am I missing something here? Other than for fun/hobby/loving to tinker, and given the price and hash rate of the U1s, why would anyone buy the Gridseed 5 chip Dual Miner?
Is the dual mining such an amazing option?
To be fair, they do look pretty kewl, and I do wish someone with some design sense would address the current state of affairs of the flat rectangular USBs we have now, but that Gridseed seems really pricey.
Topic: Bitmain AntMiner U1 Tips & Tricks - page 6. (Read 106808 times)
wow very impressive 
hope you dont mind me asking a few questions 
are you running that off the raspberry pi in the lower picture? and if so how are you configuring the USB? (something like PI>>un-powered hub>>powered hubs/ants?)
also did you have to do the resistor swaps to get the speed above 2Gh/s?
and did you have to direct wire the hubs? and chance of a link to the info or pic
thanks in advance
hope you dont mind me asking a few questions are you running that off the raspberry pi in the lower picture? and if so how are you configuring the USB? (something like PI>>un-powered hub>>powered hubs/ants?)
also did you have to do the resistor swaps to get the speed above 2Gh/s?
and did you have to direct wire the hubs? and chance of a link to the info or pic
thanks in advance
Yes, its running on/with raspberry. I not configured USB, I used the Minepeon-Image and only updated bfgminer on 3.10.0. So far I not touched resistors. The Hubs are connected through a fifth HUB with 4 ports with usual USB-Cables, Power-Connection for HUBs I soldered directly on the HUB-Boards on the original Power-Connector.
Can i ask why you soldered the wires instead of use the original connectors?
also where did you solder too?, i have been googling and i cannot find a guide or and pics etc
https://docs.google.com/file/d/0B-_jcpU1s5dgVWtKeFAwWVlfZlk/edit
This is the PDF of the U1 help. Solder to the highlighted areas. The 10K (upper) resistor is empty, so just solder in a new one. The other one (just below it) needs to be removed then resoldered. Everything is surface mounted.
sorry i was re-fairing to the hubs
wow very impressive hope you dont mind me asking a few questions
are you running that off the raspberry pi in the lower picture? and if so how are you configuring the USB? (something like PI>>un-powered hub>>powered hubs/ants?)
also did you have to do the resistor swaps to get the speed above 2Gh/s?
and did you have to direct wire the hubs? and chance of a link to the info or pic
thanks in advance
hope you dont mind me asking a few questions are you running that off the raspberry pi in the lower picture? and if so how are you configuring the USB? (something like PI>>un-powered hub>>powered hubs/ants?)
also did you have to do the resistor swaps to get the speed above 2Gh/s?
and did you have to direct wire the hubs? and chance of a link to the info or pic
thanks in advance
Yes, its running on/with raspberry. I not configured USB, I used the Minepeon-Image and only updated bfgminer on 3.10.0. So far I not touched resistors. The Hubs are connected through a fifth HUB with 4 ports with usual USB-Cables, Power-Connection for HUBs I soldered directly on the HUB-Boards on the original Power-Connector.
Can i ask why you soldered the wires instead of use the original connectors?
also where did you solder too?, i have been googling and i cannot find a guide or and pics etc
https://docs.google.com/file/d/0B-_jcpU1s5dgVWtKeFAwWVlfZlk/edit
This is the PDF of the U1 help. Solder to the highlighted areas. The 10K (upper) resistor is empty, so just solder in a new one. The other one (just below it) needs to be removed then resoldered. Everything is surface mounted.
wow very impressive hope you dont mind me asking a few questions
are you running that off the raspberry pi in the lower picture? and if so how are you configuring the USB? (something like PI>>un-powered hub>>powered hubs/ants?)
also did you have to do the resistor swaps to get the speed above 2Gh/s?
and did you have to direct wire the hubs? and chance of a link to the info or pic
thanks in advance
hope you dont mind me asking a few questions are you running that off the raspberry pi in the lower picture? and if so how are you configuring the USB? (something like PI>>un-powered hub>>powered hubs/ants?)
also did you have to do the resistor swaps to get the speed above 2Gh/s?
and did you have to direct wire the hubs? and chance of a link to the info or pic
thanks in advance
Yes, its running on/with raspberry. I not configured USB, I used the Minepeon-Image and only updated bfgminer on 3.10.0. So far I not touched resistors. The Hubs are connected through a fifth HUB with 4 ports with usual USB-Cables, Power-Connection for HUBs I soldered directly on the HUB-Boards on the original Power-Connector.
Can i ask why you soldered the wires instead of use the original connectors?
also where did you solder too?, i have been googling and i cannot find a guide or and pics etc
Can i ask why you soldered the wires instead of use the original connectors?
The original supplies were to weak and the PC-Supply of course not had round connectors - so instead of buy extra plugs - I thought its simple solution to solder the cables directly.
wow very impressive hope you dont mind me asking a few questions
are you running that off the raspberry pi in the lower picture? and if so how are you configuring the USB? (something like PI>>un-powered hub>>powered hubs/ants?)
also did you have to do the resistor swaps to get the speed above 2Gh/s?
and did you have to direct wire the hubs? and chance of a link to the info or pic
thanks in advance
hope you dont mind me asking a few questions are you running that off the raspberry pi in the lower picture? and if so how are you configuring the USB? (something like PI>>un-powered hub>>powered hubs/ants?)
also did you have to do the resistor swaps to get the speed above 2Gh/s?
and did you have to direct wire the hubs? and chance of a link to the info or pic
thanks in advance
Yes, its running on/with raspberry. I not configured USB, I used the Minepeon-Image and only updated bfgminer on 3.10.0. So far I not touched resistors. The Hubs are connected through a fifth HUB with 4 ports with usual USB-Cables, Power-Connection for HUBs I soldered directly on the HUB-Boards on the original Power-Connector.
Can i ask why you soldered the wires instead of use the original connectors?
wow very impressive hope you dont mind me asking a few questions
are you running that off the raspberry pi in the lower picture? and if so how are you configuring the USB? (something like PI>>un-powered hub>>powered hubs/ants?)
also did you have to do the resistor swaps to get the speed above 2Gh/s?
and did you have to direct wire the hubs? and chance of a link to the info or pic
thanks in advance
hope you dont mind me asking a few questions are you running that off the raspberry pi in the lower picture? and if so how are you configuring the USB? (something like PI>>un-powered hub>>powered hubs/ants?)
also did you have to do the resistor swaps to get the speed above 2Gh/s?
and did you have to direct wire the hubs? and chance of a link to the info or pic
thanks in advance
Yes, its running on/with raspberry. I not configured USB, I used the Minepeon-Image and only updated bfgminer on 3.10.0. So far I not touched resistors. The Hubs are connected through a fifth HUB with 4 ports with usual USB-Cables, Power-Connection for HUBs I soldered directly on the HUB-Boards on the original Power-Connector.
I use actual 23 Antminers on 4 Dlink DUB-H7 - 3 are full and one just with 2 miners at the moment.
The HUBs are powered by a 350W PC-Supply and Ants are running without mod on 0A81 stable.
Cooling from downside from power-supply and from front with 120mm Fan running on 5V silent.
At all actual power consum 72W ! I have an asic-cube also taking arround 300W for less GH.
http://www.teneco.net/ants/1.png
http://www.teneco.net/ants/2.png
http://www.teneco.net/ants/IMG_2228s.JPG
http://www.teneco.net/ants/IMG_2239s.JPG
The HUBs are powered by a 350W PC-Supply and Ants are running without mod on 0A81 stable.
Cooling from downside from power-supply and from front with 120mm Fan running on 5V silent.
At all actual power consum 72W ! I have an asic-cube also taking arround 300W for less GH.
http://www.teneco.net/ants/1.png
http://www.teneco.net/ants/2.png
http://www.teneco.net/ants/IMG_2228s.JPG
http://www.teneco.net/ants/IMG_2239s.JPG
wow very impressive
hope you dont mind me asking a few questions are you running that off the raspberry pi in the lower picture? and if so how are you configuring the USB? (something like PI>>un-powered hub>>powered hubs/ants?)
also did you have to do the resistor swaps to get the speed above 2Gh/s?
and did you have to direct wire the hubs? and chance of a link to the info or pic
thanks in advance
I use actual 23 Antminers on 4 Dlink DUB-H7 - 3 are full and one just with 2 miners at the moment.
The HUBs are powered by a 350W PC-Supply and Ants are running without mod on 0A81 stable.
Cooling from downside from power-supply and from front with 120mm Fan running on 5V silent.
At all actual power consum 72W ! I have an asic-cube also taking arround 300W for less GH.
http://www.teneco.net/ants/1.png
http://www.teneco.net/ants/2.png
http://www.teneco.net/ants/IMG_2228s.JPG
http://www.teneco.net/ants/IMG_2239s.JPG
The HUBs are powered by a 350W PC-Supply and Ants are running without mod on 0A81 stable.
Cooling from downside from power-supply and from front with 120mm Fan running on 5V silent.
At all actual power consum 72W ! I have an asic-cube also taking arround 300W for less GH.
http://www.teneco.net/ants/1.png
http://www.teneco.net/ants/2.png
http://www.teneco.net/ants/IMG_2228s.JPG
http://www.teneco.net/ants/IMG_2239s.JPG
Can anyone offer any advice on this? Are the above values safe to use without permanently damaging the unit's clock generation in some way?
I've used 100 MHash/s steps a lot for testing/fine tuning individual ants. No harm done. 
It is quite comfortable but has one astonishing problem... it only accepts multiples of 25
I wanted to try frequencies like the earlier reported 262.50mhz but that's a no go.
Can anyone offer any advice on this? Are the above values safe to use without permanently damaging the unit's clock generation in some way?
I've used 100 MHash/s steps a lot for testing/fine tuning individual ants. No harm done. Hi,
just in case someone needs a finer speed setting:
Frequency | Hashrate | value | timeout
125.00 MHz | 1000 MHs | 0481 | 042 ms
137.50 MHz | 1100 MHs | 0501 | 039 ms
150.00 MHz | 1200 MHs | 0581 | 035 ms
162.50 MHz | 1300 MHs | 0601 | 033 ms
175.00 MHz | 1400 MHs | 0681 | 030 ms
187.50 MHz | 1500 MHs | 0701 | 028 ms
200.00 MHz | 1600 MHs | 0781 | 026 ms
212.50 MHz | 1700 MHs | 0801 | 025 ms
225.00 MHz | 1800 MHs | 0881 | 023 ms
237.50 MHz | 1900 MHs | 0901 | 022 ms
250.00 MHz | 2000 MHs | 0981 | 021 ms
262.50 MHz | 2100 MHs | 0A01 | 020 ms
275.00 MHz | 2200 MHs | 0A81 | 019 ms
or even finer for tweaking your individual miner:
237.50 MHz | 1900 MHs | 1285 | 022 ms
243.75 MHz | 1950 MHs | 1305 | 022 ms
250.00 MHz | 2000 MHs | 1385 | 021 ms
256.25 MHz | 2050 MHs | 1405 | 020 ms
262.50 MHz | 2100 MHs | 1485 | 020 ms
268.75 MHz | 2150 MHs | 1505 | 019 ms
275.00 MHz | 2200 MHs | 1585 | 019 ms
281.25 MHz | 2250 MHs | 1605 | 019 ms
287.50 MHz | 2300 MHs | 1685 | 018 ms
293.75 MHz | 2350 MHs | 1705 | 018 ms
300.00 MHz | 2400 MHs | 1785 | 017 ms
But beware. While playing around with this values or better some values not respecting the forumular given in the U1 manual I somehow wrecked my antminers clock generation.
Greetings,
miniasic.
Can anyone offer any advice on this? Are the above values safe to use without permanently damaging the unit's clock generation in some way?just in case someone needs a finer speed setting:
Frequency | Hashrate | value | timeout
125.00 MHz | 1000 MHs | 0481 | 042 ms
137.50 MHz | 1100 MHs | 0501 | 039 ms
150.00 MHz | 1200 MHs | 0581 | 035 ms
162.50 MHz | 1300 MHs | 0601 | 033 ms
175.00 MHz | 1400 MHs | 0681 | 030 ms
187.50 MHz | 1500 MHs | 0701 | 028 ms
200.00 MHz | 1600 MHs | 0781 | 026 ms
212.50 MHz | 1700 MHs | 0801 | 025 ms
225.00 MHz | 1800 MHs | 0881 | 023 ms
237.50 MHz | 1900 MHs | 0901 | 022 ms
250.00 MHz | 2000 MHs | 0981 | 021 ms
262.50 MHz | 2100 MHs | 0A01 | 020 ms
275.00 MHz | 2200 MHs | 0A81 | 019 ms
or even finer for tweaking your individual miner:
237.50 MHz | 1900 MHs | 1285 | 022 ms
243.75 MHz | 1950 MHs | 1305 | 022 ms
250.00 MHz | 2000 MHs | 1385 | 021 ms
256.25 MHz | 2050 MHs | 1405 | 020 ms
262.50 MHz | 2100 MHs | 1485 | 020 ms
268.75 MHz | 2150 MHs | 1505 | 019 ms
275.00 MHz | 2200 MHs | 1585 | 019 ms
281.25 MHz | 2250 MHs | 1605 | 019 ms
287.50 MHz | 2300 MHs | 1685 | 018 ms
293.75 MHz | 2350 MHs | 1705 | 018 ms
300.00 MHz | 2400 MHs | 1785 | 017 ms
But beware. While playing around with this values or better some values not respecting the forumular given in the U1 manual I somehow wrecked my antminers clock generation.
Greetings,
miniasic.
Thanks to all who contributed to this thread so far, it was very useful.
git clone https://github.com/signal11/hidapi ~/bfgminer/hidapi
What this is used for? I'm using bfgminer but i haven't installed hidapi (with a raspberry pi), maybe is required by the last "git version"?
Ps
Very useful thank you!!!!!!
Here is a build_bfgminer.sh script for Debian Linux that works rather well. Add any build arguments in after ./configure to customize it.
sudo rm -rfv ~/bfgminer/bfgminer
cd ~/
sudo apt-get install git build-essential autoconf automake libtool pkg-config libcurl4-gnutls-dev libjansson-dev uthash-dev libncursesw5-dev libudev-dev libusb-1.0-0-dev libevent-dev libmicrohttpd-dev uthash-dev
git clone https://github.com/luke-jr/bfgminer.git ~/bfgminer
git clone https://github.com/signal11/hidapi ~/bfgminer/hidapi
cd ~/bfgminer/hidapi
sudo ./bootstrap
sudo ./configure --prefix=/usr
sudo make
sudo make install
cd ~/bfgminer
sudo ./autogen.sh
sudo ./configure
make
sudo chmod +x bfgminer
sudo rm -rfv ~/bfgminer/bfgminer
cd ~/
sudo apt-get install git build-essential autoconf automake libtool pkg-config libcurl4-gnutls-dev libjansson-dev uthash-dev libncursesw5-dev libudev-dev libusb-1.0-0-dev libevent-dev libmicrohttpd-dev uthash-dev
git clone https://github.com/luke-jr/bfgminer.git ~/bfgminer
git clone https://github.com/signal11/hidapi ~/bfgminer/hidapi
cd ~/bfgminer/hidapi
sudo ./bootstrap
sudo ./configure --prefix=/usr
sudo make
sudo make install
cd ~/bfgminer
sudo ./autogen.sh
sudo ./configure
make
sudo chmod +x bfgminer
Quote
this is really nice, but are you planning to leave this for daily use? what is the expected duration of the ants @1.1v 3gh/s?
normally its not voltage (unless really on the edge) that kills chips its the high temp (from the increased voltage) that degrades parts till they hardly/dont work, so good cooling offsets the increased voltage.
well i ordered my resistors...... hope they are the right size. smd 603/1608 metric
types are 10k, 2.49, and 5.1 100pcs ea.
which should net me:
stock=.8v
1k-10k=.88v
2.49-10k=1.0v
5.1k-10k=1.208v
if it works out i can mod them for ya or send you some resistors for a very small price. like .001 for a few via envelope
types are 10k, 2.49, and 5.1 100pcs ea.
which should net me:
stock=.8v
1k-10k=.88v
2.49-10k=1.0v
5.1k-10k=1.208v
if it works out i can mod them for ya or send you some resistors for a very small price. like .001 for a few via envelope
i do have an old thermaltake water cooling kit with 1 cpu and 2 gpu blocks. i think im gonna donate 1 of my 7 miners to the cause and see what i can pull on air then water.
same situation for me, I have a wb for cpu, one for gpu and one for chipset, all unused... And I have a 35w peltier cell as well, nice for some test :p but I'm pretty sure, with this configuration an U1 lasts little... so it coulb be for testing purpose, not for daily mining.
Let us know about the tests!
this is really nice, but are you planning to leave this for daily use? what is the expected duration of the ants @1.1v 3gh/s?
Hi,
my plan was to build it.
i like to build thinks and if anybody is intrested in it a can sell it too.
...Tested every single Antminer with my Notebook Win7 and CGminer 3.12.3.
...I got 2,8 Ghash out of every Stick.
...I got 2,8 Ghash out of every Stick.
Well then, looks like a current limitation on the hub. The mentioned detection/communication issues might be related to this as well.
Update:
Compiled the actual version of cgminer. This actualy did detect 11 of my 16 Ants and gave them bad performance and lots of errors:
Then I self compiled actual version of bfgminer from github. For some reason this is now running better then previously. All (but one) are running well at 2,2 Ghash now.
As long as nobody has a good hint I will now let it run as is and retry with newer versions of cgminer/bfgminer
Compiled the actual version of cgminer. This actualy did detect 11 of my 16 Ants and gave them bad performance and lots of errors:
Then I self compiled actual version of bfgminer from github. For some reason this is now running better then previously. All (but one) are running well at 2,2 Ghash now.
As long as nobody has a good hint I will now let it run as is and retry with newer versions of cgminer/bfgminer
Jump to: