I can usually fumble my way through linux, vi, and an ssh interface.
I assume you meant cgminer.conf. The value 415 is not available in the web interface drop down. Changing the 410 to 415 in cgminer.conf results in the listed frequencies in the Miner Status page to show 415. Going to the Advanced Settings page where you would normally change the frequencies using the drop down, the drop down box is blank.
For this test, I had to reboot the miner via the web interface. How do you restart cgminer through the ssh?
Topic: Bitmain launches the new AntMiner DR3 (Decred ASIC Miner) - page 3. (Read 2867 times)
Yep, those worked. Here's the interesting info of the cgminer.conf (after the pool info):
"api-listen" : true,
"api-network" : true,
"api-groups" : "A:stats:pools:devs:summary:version",
"api-allow" : "A:0/0,W:*",
"bitmain-fan-ctrl" : true,
"bitmain-fan-pwm" : "100",
"bitmain-use-vil" : true,
"bitmain-freq" : "410"
Anything specifically, I can help out with? Feel free to PM me.
"api-listen" : true,
"api-network" : true,
"api-groups" : "A:stats:pools:devs:summary:version",
"api-allow" : "A:0/0,W:*",
"bitmain-fan-ctrl" : true,
"bitmain-fan-pwm" : "100",
"bitmain-use-vil" : true,
"bitmain-freq" : "410"
Anything specifically, I can help out with? Feel free to PM me.
Yeah, just something simple, pick any frequency that is NOT in the list on the web page, and change the '410' value to that freq. like, if 415 isn't listed, change 410 to 415. (I assume you know how to use vi? I'll try to describe the actual commands, one per line, just below this comment by pretending I'm editing it... Once that's done, run "/etc/init.d/cgminer.sh restart". All I'm looking to see is if the actual frequency changes to what you put in (like 415) or if it goes back to 410. The change will show up in the web interface with the regular miner stats.
SSH in, type these commands:
vi /config/cgminer.sh (hit enter)
/410
cw415 (Hit Escape)
:wq! (hit enter)
Then restart cgminer.sh
So that's literally typing 'c', then 'w', then '4', then '1', then '0', as if it was one word. no spaces, no enters, only, etc.
Thank you for helping as best you can!
-j
Yep, those worked. Here's the interesting info of the cgminer.conf (after the pool info):
"api-listen" : true,
"api-network" : true,
"api-groups" : "A:stats:pools:devs:summary:version",
"api-allow" : "A:0/0,W:*",
"bitmain-fan-ctrl" : true,
"bitmain-fan-pwm" : "100",
"bitmain-use-vil" : true,
"bitmain-freq" : "410"
Anything specifically, I can help out with? Feel free to PM me.
"api-listen" : true,
"api-network" : true,
"api-groups" : "A:stats:pools:devs:summary:version",
"api-allow" : "A:0/0,W:*",
"bitmain-fan-ctrl" : true,
"bitmain-fan-pwm" : "100",
"bitmain-use-vil" : true,
"bitmain-freq" : "410"
Anything specifically, I can help out with? Feel free to PM me.
try root/admin
that's the default unless you change the password in the web server.
that's the default unless you change the password in the web server.
What kind of temps are your dr3 chips running at and at how much wall power?
Mine temps are 88C, 85C, and 83C at 100% fan and my meter is telling me it's pulling 1570W. Miner says it's between 7.8 and 7.9 Th/s.
At least I don't have any chain errors and my HW errors are relatively low (less than 50 after 10min).
Mine temps are 88C, 85C, and 83C at 100% fan and my meter is telling me it's pulling 1570W. Miner says it's between 7.8 and 7.9 Th/s.
At least I don't have any chain errors and my HW errors are relatively low (less than 50 after 10min).
what frequencies are available by default?
Can you set a frequency other than the included ones via the browser/inspect or editing /config/cgminer.comf?
If so, I can move on, if not, I want get get the firmware and open it up.
-j
Default frequency is set to 410M. Looks like normal frequencies available to select up to 450M are available. I tried SSH into the miner with user/pass as root/root but denied. I'm not really comfortable with setting new frequencies yet as I'm still gauging default characteristics, but would be happy to get you firmware image if you know of a way.
What kind of temps are your dr3 chips running at and at how much wall power?
Mine temps are 88C, 85C, and 83C at 100% fan and my meter is telling me it's pulling 1570W. Miner says it's between 7.8 and 7.9 Th/s.
At least I don't have any chain errors and my HW errors are relatively low (less than 50 after 10min).
Mine temps are 88C, 85C, and 83C at 100% fan and my meter is telling me it's pulling 1570W. Miner says it's between 7.8 and 7.9 Th/s.
At least I don't have any chain errors and my HW errors are relatively low (less than 50 after 10min).
what frequencies are available by default?
Can you set a frequency other than the included ones via the browser/inspect or editing /config/cgminer.comf?
If so, I can move on, if not, I want get get the firmware and open it up.
-j
What kind of temps are your dr3 chips running at and at how much wall power?
Mine temps are 88C, 85C, and 83C at 100% fan and my meter is telling me it's pulling 1570W. Miner says it's between 7.8 and 7.9 Th/s.
At least I don't have any chain errors and my HW errors are relatively low (less than 50 after 10min).
Mine temps are 88C, 85C, and 83C at 100% fan and my meter is telling me it's pulling 1570W. Miner says it's between 7.8 and 7.9 Th/s.
At least I don't have any chain errors and my HW errors are relatively low (less than 50 after 10min).
UK import fees £120.12
here's the fees UPS wants:
$189.18 USD
for one unit..
They better get those American ASIC companies up and running pronto (so we can pay like 15% more than before, but 10% less than we have to pay now) $189.18 USD
for one unit..
here's the fees UPS wants:
$189.18 USD
for one unit..
$189.18 USD
for one unit..
https://asicminermarket.com/product/strongu-miner-stu-u1-dcr-hc-miner/
11TH/s at 1600w
Perhaps that's Bitmain starts its sale...
11TH/s at 1600w
Perhaps that's Bitmain starts its sale...
My order for the DR3 miners just arrived, YAY!!
Can it be overclocked?
EDIT: chain #3 is giving high HW errors above 1300 soon after startup on both of my dr3 (default settings)
Are you a unix-type-person? In other words, could you tar up the filesystem and share it with me?
0j
The first batch is not yet fully launched, and the profit fell to 8-10 dollars, depending on the cost of electricity.
https://www.asicminervalue.com/miners/bitmain/antminer-dr3
Now purchase orders are set for October 8-15. By this time, the profit will fall several more times and the asic may not be payable.
Those who bought in September will probably earn if they sell it now
A man giving out free advice on how to make money, seems sketchier than paying $99 for an ebook lol https://www.asicminervalue.com/miners/bitmain/antminer-dr3
Now purchase orders are set for October 8-15. By this time, the profit will fall several more times and the asic may not be payable.
Those who bought in September will probably earn if they sell it now
Luxor is good and they're only a 1% fee PPS, but they haven't implemented user accounts yet so the payouts are fixed at 0.2 intervals. I've been using Luxor and https://www2.coinmine.pl/dcr/ for the past 5 months (coinmine is 1% fee PPLNS). Both have discord channels that they are responsive to. I'm favoring coinmine right now because they have user accounts and an android phone app so you can monitor account progress remotely.
The first batch is not yet fully launched, and the profit fell to 8-10 dollars, depending on the cost of electricity.
https://www.asicminervalue.com/miners/bitmain/antminer-dr3
Now purchase orders are set for October 8-15. By this time, the profit will fall several more times and the asic may not be payable.
Those who bought in September will probably earn if they sell it now
https://www.asicminervalue.com/miners/bitmain/antminer-dr3
Now purchase orders are set for October 8-15. By this time, the profit will fall several more times and the asic may not be payable.
Those who bought in September will probably earn if they sell it now
My order for the DR3 miners just arrived, YAY!!
Can it be overclocked?
EDIT: chain #3 is giving high HW errors above 1300 soon after startup on both of my dr3 (default settings)
Mine is arriving today. BTW, what pools do you guys have in mind?
was thinking this one:
https://mining.luxor.tech/
lower fees, decent overall rate and has a US endpoint..
Mine is arriving today. BTW, what pools do you guys have in mind?
was thinking this one:
https://mining.luxor.tech/
lower fees, decent overall rate and has a US endpoint..
My order for the DR3 miners just arrived, YAY!!
Can it be overclocked?
Mine is arriving today. BTW, what pools do you guys have in mind?
Jump to: