This is what shows up when I check dmesg too.
Code:
hub 1-2:1.0: USB hub found
hub 1-2:1.0: 4 ports detected
usb 1-2.1: new full speed USB device using ehci_hcd and address 6
usb 1-2.1: configuration #1 chosen from 1 choice
Topic: CGminer v3.8.5 on Broadcom based DD-WRT / OpenWRT - page 6. (Read 77138 times)
Well I got DD-WRT and I'm pretty sure mostly EVERYTHING is running smooth with 3.1.1(rolled back for compatibility sake) problem is my router (RT-16) does not show that any serial device is plugged in when I plug in the BE. Nothing shows up in /dev/usb/tts. This one last hurdle and I'll be happily mining away I think.
This is what shows up when I check dmesg too.
This is what shows up when I check dmesg too.
Nope, nogo. Also would using Optware for Tomato be a problem?
Yeah, S45serialmodules and ftdi_sio.ko is missing from the 3.3.1 file. Just grabbed it from the 3.2.0 file just now. Let's see if this will work. Might wanna fix that.
I already got that far, via telnet. I'm just not sure what to edit in the scripts to get Icarus working properly. When it means to uncomment the DEVS line does that mean I remove the # in the code? Where can i find the serial script file it says to copy? Trying to get this semi-ready as my BE shows up later today. I wish the instructions we're a bit more clearer.
Well I got as far as installing Optware on my RT-N16, Now I'm utterly confused on how to progress on Windows 7(copying files to Ext2 and such..) I wish the readme was formatted to be easier to understand for newbies to linux.
Use winscp to ssh into the router. Then go to the folders that the files need to go and copy them there.
The next step is to ssh into the router an use chmod to make those files executable.
Well I got as far as installing Optware on my RT-N16, Now I'm utterly confused on how to progress on Windows 7(copying files to Ext2 and such..) I wish the readme was formatted to be easier to understand for newbies to linux.
Has anyone got this to work with an Asicminer Erupter USB? I have a Netgear WNR3500U flashed with the latest TomatoUSB (http://tomato.groov.pl/) sitting idle and ready to start playing as soon as my Erupters arrive.
Absolutely no idea. Is it supposed to?
Have to ask Con or Kano about that.
Have to ask Con or Kano about that.
It uses the icarus protocol for mining so i should run?
CGminer must be able to use this because icarus was supported.
Absolutely no idea. Is it supposed to?
Have to ask Con or Kano about that.
Have to ask Con or Kano about that.
Do the Blockeruptor USB run with this?
I can not get them to work with 3.1.1
I can not get them to work with 3.1.1
I had it all running on my router. The web pages only use a little CPU time on page loads. Since you'll only serving pages to yourself and you're not hitting refresh every second, it's fine.
Optware has lighttpd we server. No single tutorial to set it up, but with some know-how and Googling you can get it up and running.
Optware has lighttpd we server. No single tutorial to set it up, but with some know-how and Googling you can get it up and running.
Thanks P_Shep!
I just got it working on an Asus RT-N16 running TomatoUSB firmware with a blackarrow Lancelot FPGA. I'll try getting Anubis to monitor it next. Would you recommend running Anubis on the router or on another PC on the same LAN?
I just got it working on an Asus RT-N16 running TomatoUSB firmware with a blackarrow Lancelot FPGA. I'll try getting Anubis to monitor it next. Would you recommend running Anubis on the router or on another PC on the same LAN?
I have anubis on my raspberry pi. I could not find a good TuT to get it working on my router :/ Do you have one?
Thanks P_Shep!
I just got it working on an Asus RT-N16 running TomatoUSB firmware with a blackarrow Lancelot FPGA. I'll try getting Anubis to monitor it next. Would you recommend running Anubis on the router or on another PC on the same LAN?
I just got it working on an Asus RT-N16 running TomatoUSB firmware with a blackarrow Lancelot FPGA. I'll try getting Anubis to monitor it next. Would you recommend running Anubis on the router or on another PC on the same LAN?
Nice set up!
Hmmm, there was supposed to be big changes with regards to the USB stuff, and was the ZTEX code changed to LibUSB-1.0?
Probably best stick with 3.1.1 then.
Probably best stick with 3.1.1 then.
I'll revert back to 3.1.1 later.
For the changes in cgminer I have no clue
Hmmm, there was supposed to be big changes with regards to the USB stuff, and was the ZTEX code changed to LibUSB-1.0?
Probably best stick with 3.1.1 then.
Probably best stick with 3.1.1 then.
Gives me errors on the Quads:
Quote
[2013-06-03 17:14:06] Found ztex board 1.15y
[2013-06-03 17:14:40] ZTEX 04A36E24F2-4: resetting 26.0 errors
[2013-06-03 17:14:40] ZTEX 04A36E24F2-1: resetting 26.0 errors
[2013-06-03 17:14:40] ZTEX 04A36E24F2-3: resetting 26.0 errors
[2013-06-03 17:14:40] ZTEX 04A36E24F2-2: resetting 26.0 errors
(5s):1.417G (avg):691.2Mh/s | A:0 R:0 HW:13 U:0.0/m WU:16.0/m
[2013-06-03 17:14:40] ZTEX 04A36E24F2-4: resetting 26.0 errors
[2013-06-03 17:14:40] ZTEX 04A36E24F2-1: resetting 26.0 errors
[2013-06-03 17:14:40] ZTEX 04A36E24F2-3: resetting 26.0 errors
[2013-06-03 17:14:40] ZTEX 04A36E24F2-2: resetting 26.0 errors
(5s):1.417G (avg):691.2Mh/s | A:0 R:0 HW:13 U:0.0/m WU:16.0/m
And the Singles:
Quote
[2013-06-03 17:19:53] Found ztex board 1.15d or 1.15x
[2013-06-03 17:19:53] ZTEX 04A346E12C-1: capability missing: 0 7
[2013-06-03 17:20:05] ZTEX 04A346E12C-1: HS FPGA configuration failed: DONE pin does not go high
[2013-06-03 17:20:34] ZTEX 04A346E12C-1: resetting 26.0 errors
(5s):93.48M (avg):179.7Mh/s | A:0 R:0 HW:3 U:0.0/m WU:1.5/m
[2013-06-03 17:19:53] ZTEX 04A346E12C-1: capability missing: 0 7
[2013-06-03 17:20:05] ZTEX 04A346E12C-1: HS FPGA configuration failed: DONE pin does not go high
[2013-06-03 17:20:34] ZTEX 04A346E12C-1: resetting 26.0 errors
(5s):93.48M (avg):179.7Mh/s | A:0 R:0 HW:3 U:0.0/m WU:1.5/m
Nice work P_Shep.
Unlike previously, I have to compile cgminer for mips these days since that's what runs directly on avalon so hopefully things run more smoothly for you now.
Unlike previously, I have to compile cgminer for mips these days since that's what runs directly on avalon so hopefully things run more smoothly for you now.
You guys removed FPGA support on avalons cgminer?
I flashed one of my 703n with avalon firmware, but I couldnt make cgminer recognize my fpgas.
Can you help me compile last version for 703n and make my own image?
Jump to: