Then elaborate on your original statement - why hasn't your miner hashed for the last two months? What do you mean "the correct pool" ? There is no one answer to that question, so we need some more information about what you're looking for.
I'm not sure where you came up with "last two months"......I said" I have had mine for over a month and it has not hashed for 2 minutes"...but what ever....some people say you need #xsnub at the end of the pool address and some say to put "x" in for a password and some say to put "c=BTC,d=512"....I just wanted to know which it is!!! 
Topic: Dayun Zig Z1 - Lyra2Rev2 6.8GH/s Asic miner - page 9. (Read 42511 times)
Then elaborate on your original statement - why hasn't your miner hashed for the last two months? What do you mean "the correct pool" ? There is no one answer to that question, so we need some more information about what you're looking for.
Go choose any coin that's lyra2rev2 compatible, and find pools that support that coin. Or, point it to Nicehash and sell the hashrate directly. It's your choice...
Been there and done all that...........This is not my first miner.
Go choose any coin that's lyra2rev2 compatible, and find pools that support that coin. Or, point it to Nicehash and sell the hashrate directly. It's your choice...
You can choose whatever pool you want. Maybe you should've done some research before buying it, if you don't understand what you're doing that's not the manufacturer's fault.
I can choose what ever pool I want?? Really??
You can choose whatever pool you want. Maybe you should've done some research before buying it, if you don't understand what you're doing that's not the manufacturer's fault.
Can someone tell me which files you upload in the miner interface and which files do you put on the usb drive? Are these 2 different files? My miner has 20180926 showing on the upload page on the miner. Can't get the miner to hash!!
On the usb you have everything, you have a part to boot your miner and also you have the firmware on it.
In my case I was not able to boot, so I had follow the procedure to make a new usb key. So I bought a new 16 Gig usb key. And I did what you have at this link: https://drive.google.com/drive/folders/1Y1YXEgEnIFVnmzmD7PaTAMrVEDikTrfR ( the new image at this link put a static ip adress that is 192.168.1.100)
Did you allready succed to mine with your Zig Z1 in the past?
If not, it's probable your pool information that is not good.
That depends on your dexterity, of course, but it took me approximately 30 minutes to disassemble an RR210 and repaste all the boards.
Any idea on how and how long to recompound?
What do you mean "how long" ?
Any idea on how and how long to recompound?
What do you mean "how long" ?
Can someone tell me which files you upload in the miner interface and which files do you put on the usb drive? Are these 2 different files? My miner has 20180926 showing on the upload page on the miner. Can't get the miner to hash!!
On the usb you have everything, you have a part to boot your miner and also you have the firmware on it.
In my case I was not able to boot, so I had follow the procedure to make a new usb key. So I bought a new 16 Gig usb key. And I did what you have at this link: https://drive.google.com/drive/folders/1Y1YXEgEnIFVnmzmD7PaTAMrVEDikTrfR ( the new image at this link put a static ip adress that is 192.168.1.100)
Did you allready succed to mine with your Zig Z1 in the past?
If not, it's probable your pool information that is not good.
this is happening to me and i have a few in the red as well. Does this mean its time to clean the chips and install new thermal compound paste?
This is firmware problems, and chip qualities -> you can use firmware 0930 oc mode to fixed this and If you have enough fund to spend in thermal compound you can change it , because the old thermal compound isn't good enough . It will improved stabilities to mining
this is happening to me and i have a few in the red as well. Does this mean its time to clean the chips and install new thermal compound paste?
This is firmware problems, and chip qualities -> you can use firmware 0930 oc mode to fixed this and If you have enough fund to spend in thermal compound you can change it , because the old thermal compound isn't good enough . It will improved stabilities to mining
here is my feedback.
got the miner 3 days ago
to make it go online had to change the ip to .10 instead of .100 and put manually DNS server name
then tried different pools. nicehash, MPH, powermining. all same performance, 1 board not hashing fine.
changing frequency doesn't seem to do a big deal, with 900 one board stays dead all the time, with 800 dies after a while.
sent message to crypto drilling (shop I bought) and told me to freq 845 (which I can only put 850)
waiting for their technical team to reply..
this is my configuration
https://www.screencast.com/t/BLnyFx0I
https://www.screencast.com/t/pBDcSQmGpwe
and this is the results
https://www.screencast.com/t/2nltNThwIBQ
hash rate quite erratic but never higher than 5GH
https://www.screencast.com/t/8cvezEcAnD
nicehash stats
https://www.screencast.com/t/XuROlvulVA
any feedback or suggestion, very welcome
got the miner 3 days ago
to make it go online had to change the ip to .10 instead of .100 and put manually DNS server name
then tried different pools. nicehash, MPH, powermining. all same performance, 1 board not hashing fine.
changing frequency doesn't seem to do a big deal, with 900 one board stays dead all the time, with 800 dies after a while.
sent message to crypto drilling (shop I bought) and told me to freq 845 (which I can only put 850)
waiting for their technical team to reply..
this is my configuration
https://www.screencast.com/t/BLnyFx0I
https://www.screencast.com/t/pBDcSQmGpwe
Code:
{
"pools": [
{
"url": "stratum+tcp:\/\/lyra2rev2.eu.nicehash.com:3347",
"user": "3GKgz3dj7nE3NFdrEECKdqjQf1US5rz6YR",
"pass": "x"
},
{
"url": "stratum+tcp:\/\/pool.powermining.pw:4535",
"user": "MErJBFcuRdAYCSidG3P8UQYmXVFmhpK53j",
"pass": "x"
},
{
"url": "stratum+tcp:\/\/hub.miningpoolhub.com:12018",
"user": "roberto_f.zig",
"pass": "x"
}
],
"api-allow": "W:0\/0",
"api-description": "cgminer 4.11.1",
"api-listen": true,
"api-mcast-addr": "224.0.0.75",
"api-mcast-code": "FTW",
"api-mcast-des": "",
"api-mcast-port": "4028",
"api-network": true,
"api-port": "4028",
"expiry": "120",
"failover-switch-delay": "300",
"log": "5",
"queue": "9999",
"scan-time": "60",
"shares": "0",
"lyra2rev2-clk": "850",
"lyra2rev2-vol": "0",
"lyra2rev2-asic-x": "4",
"lyra2rev2-asic-y": "24",
"lyra2rev2-asic-num": "50",
"lyra2rev2-cutofftemperature": "50",
"lyra2rev2-cutofffanspeedin": "100",
"lyra2rev2-cutofffanspeedout": "100",
"lyra2rev2-restarthashrate": "3",
"lyra2rev2-restartfailedcount": "100",
"lyra2rev2-fan": "LV1",
"lyra2rev2-check-testnonce": true,
"lyra2rev2-scan-serial": "\/dev\/ttyS3",
"lyra2rev2-restartenable": true,
"lyra2rev2-cutoffenable": true
}
"pools": [
{
"url": "stratum+tcp:\/\/lyra2rev2.eu.nicehash.com:3347",
"user": "3GKgz3dj7nE3NFdrEECKdqjQf1US5rz6YR",
"pass": "x"
},
{
"url": "stratum+tcp:\/\/pool.powermining.pw:4535",
"user": "MErJBFcuRdAYCSidG3P8UQYmXVFmhpK53j",
"pass": "x"
},
{
"url": "stratum+tcp:\/\/hub.miningpoolhub.com:12018",
"user": "roberto_f.zig",
"pass": "x"
}
],
"api-allow": "W:0\/0",
"api-description": "cgminer 4.11.1",
"api-listen": true,
"api-mcast-addr": "224.0.0.75",
"api-mcast-code": "FTW",
"api-mcast-des": "",
"api-mcast-port": "4028",
"api-network": true,
"api-port": "4028",
"expiry": "120",
"failover-switch-delay": "300",
"log": "5",
"queue": "9999",
"scan-time": "60",
"shares": "0",
"lyra2rev2-clk": "850",
"lyra2rev2-vol": "0",
"lyra2rev2-asic-x": "4",
"lyra2rev2-asic-y": "24",
"lyra2rev2-asic-num": "50",
"lyra2rev2-cutofftemperature": "50",
"lyra2rev2-cutofffanspeedin": "100",
"lyra2rev2-cutofffanspeedout": "100",
"lyra2rev2-restarthashrate": "3",
"lyra2rev2-restartfailedcount": "100",
"lyra2rev2-fan": "LV1",
"lyra2rev2-check-testnonce": true,
"lyra2rev2-scan-serial": "\/dev\/ttyS3",
"lyra2rev2-restartenable": true,
"lyra2rev2-cutoffenable": true
}
and this is the results
https://www.screencast.com/t/2nltNThwIBQ
hash rate quite erratic but never higher than 5GH
https://www.screencast.com/t/8cvezEcAnD
nicehash stats
https://www.screencast.com/t/XuROlvulVA
any feedback or suggestion, very welcome
Hello Roberto_F
About the non active chips you have on the "ASIC Status" page.
Here is what i do when i have the same problem (Status black, yellow or red)
Go on the Settings page and just hit the "Save and Restart Miner" button.
Check after 2-3 mins on the "ASIC Status" page if its better. If not...hit that "Save and Restart Miner" button again.
Again, go check after 2-3 mins on the "ASIC Status" page if its better. If not, try this tome the "Save and Restart Machine" button.
Now wait 5mins and then check the "ASIC Status" page. If its's better...good, if not, pull the plug from the PSU and wait 10-15min.
Pull the plug back in and wait...
Again, check the "ASIC Status" page...if it's not better, repeate the steps above.
Sometime i need "only" 15 mins to make the chips all green...
One time it took my almost 1h...but it works.
My config is with 900MHz, mining on NH and the new Firmware.
Good luck and have fun.
EDIT: Sometimes some chips need more time to turn from black to green.
So if most chips on a card are green and just a few black, i just wait 2-3mins and then they turn green.
this is happening to me and i have a few in the red as well. Does this mean its time to clean the chips and install new thermal compound paste?
Can someone tell me which files you upload in the miner interface and which files do you put on the usb drive? Are these 2 different files? My miner has 20180926 showing on the upload page on the miner. Can't get the miner to hash!!
On the usb you have everything, you have a part to boot your miner and also you have the firmware on it.
In my case I was not able to boot, so I had follow the procedure to make a new usb key. So I bought a new 16 Gig usb key. And I did what you have at this link: https://drive.google.com/drive/folders/1Y1YXEgEnIFVnmzmD7PaTAMrVEDikTrfR ( the new image at this link put a static ip adress that is 192.168.1.100)
Can someone tell me which files you upload in the miner interface and which files do you put on the usb drive? Are these 2 different files? My miner has 20180926 showing on the upload page on the miner. Can't get the miner to hash!!
On the usb you have everything, you have a part to boot your miner and also you have the firmware on it.
In my case I was not able to boot, so I had follow the procedure to make a new usb key. So I bought a new 16 Gig usb key. And I did what you have at this link: https://drive.google.com/drive/folders/1Y1YXEgEnIFVnmzmD7PaTAMrVEDikTrfR ( the new image at this link put a static ip adress that is 192.168.1.100)
Can someone tell me which files you upload in the miner interface and which files do you put on the usb drive? Are these 2 different files? My miner has 20180926 showing on the upload page on the miner. Can't get the miner to hash!!
You probably need to set fixed difficulty, Z1+ does 7.2GH/s and higher if configured properly.
what would you recommend for difficulty setting?
I am using difficulty 512, only 2 % reject with these settings
stratum+tcp://mine.nlpool.nl:4533
My wallet address as USER NAME>
c=BTC,d=512 as pass
on zpool using d=2000 seems to work like a charm
You probably need to set fixed difficulty, Z1+ does 7.2GH/s and higher if configured properly.
what would you recommend for difficulty setting?
I am using difficulty 512, only 2 % reject with these settings
stratum+tcp://mine.nlpool.nl:4533
My wallet address as USER NAME>
c=BTC,d=512 as pass
You probably need to set fixed difficulty, Z1+ does 7.2GH/s and higher if configured properly.
what would you recommend for difficulty setting?
Only manual restart will help.
Jump to: