Topic: [DOWN] Bitlc.net - P2SH, No invalid blocks, Custom payouts, EU, 0% fee, LP - page 40. (Read 180991 times)

Quote from: Oldminer on June 12, 2011, 07:20:05 PM

Well I had 1.4 and 1.48 in the same folder compressed so I decompressed 1.48 to make sure that's the one it was running
I'm pretty sure I'm running 1.48 though.

I'm in Canada

edit: So far I'm running at 100% but only started it a few minutes ago.

On another note, my 4870 is running at 85-86mh/s stable.

edit2: after making sure I have 1.48, I'm still getting about 4-5%

edit3: After a bit more tweeking, I now have my 4870 up to 88-89mh/s. Sweeeeeeet

So, after doing that, my rejected is up to 23%.

All I did was turn on phatk. I had fastloop on before too when I was getting 4%. I've since turned both off and I'll look into both to see what exactly they do. Ah being a nub.

Fastloop: the fast loop argument for Phoenix. Can possibly increase mining speed if enabled.
phatk: uses the phatk kernel, optimization for HD58xx series only I think? You MUST have phatk already inside the kernels folder.

I took out all flags (bfi_int vectors worksize=128) and now mh/s is back up to 89. Before taking out those flags I was at 85mh/s with 10% rejected.

Still getting 8.5% rejected

edit: Just turned off fastloop, currently have 13 accepted and 0 rejected while still getting 89mh/s. Will let it run for a while like this.

annnnnd same issue. 11% rejected as of now.

i have 2 video cards, 6990 and 4870x2. on the 6990 i get 1% rejected and on the 4870x2 i get 90% rejected.
what am i doing wrong?
im starting the 6990 with this:

./phoenix.py -u http://XXXX:[email protected]:8080/ -k poclbm Device=0 VECTORS AGGRESSION=13 WORKSIZE=128 BFI_INT FASTLOOP=false

and i start the 4870x2 with this:

./phoenix.py -u http://XXXX:[email protected]:8080/ -k poclbm Device=2 AGGRESSION=13 WORKSIZE=256

please help:)
thanks.

ok so im still mining in this pool with my 6990 at 750 Mhash/s with 1% rejection.
BUT, on my 4870x2 i changed pool to btcguild and i got 0 (zero) rejection.

is something wrong with this pool? this pool dont accept or dont work well with cards (4870x2) that give low Mhash/s? why does my 6990 get 1% rejection while my 4870x2 get 95% on this pool?

i like this pool and i want to use one pool instead of tow pools.

muyoso

member

Activity: 84

Merit: 10

Ok, call me blind but I've had to reinstall windows and need to setup my miner again, but for the life of me I cant find your miner config settings anywhere on your site? As a suggestion, perhaps you could put the host and port number etc under where we get our worker settings?

http://bitcoins.wikispaces.com/FAQ

Towards the bottom.

Oldminer

legendary

Activity: 1022

Merit: 1001

Ok, call me blind but I've had to reinstall windows and need to setup my miner again, but for the life of me I cant find your miner config settings anywhere on your site? As a suggestion, perhaps you could put the host and port number etc under where we get our worker settings?

pandemic

sr. member

Activity: 434

Merit: 250

Sooo is the payout going to be stopped until further notice or how is this working?

last I checked, I was getting a huge % of rejection - 20-40%

edit: since then it's not been that bad. I bumped aggression up from 9 to 10 and got a 2% rejection rate. I'm going to try it with aggression 12 right now to see if it'll be even lower.

edit 2: Aggression 12 = 29 accepted and 0 rejected. So far so good. I just didn't think the aggression would change the rejection rate.

edit 3: And it's back up to 10% rejected.

Jine

sr. member

Activity: 403

Merit: 250

I'm positive. 110% sure.

NO shares we're lost as the main target was the website.
We have taken actions make sure that the attack doesn't affect the site or the pool. (See our twitter)

Now back to work, bye

--
Regards, Jim

Modoki

newbie

Activity: 22

Merit: 0

Ehm, are you sure the shares are recorded still? I don't want to waste all my mining power if I dont see any btc.
Also, do you know more about the DDoS now and has it fully stopped?
Greets, M

darkpandora

member

Activity: 98

Merit: 10

Quote from: Slasklitta on June 12, 2011, 03:10:36 PM

Quote from: darkpandora on June 12, 2011, 02:25:21 PM

Quote from: Jine on June 12, 2011, 02:24:41 PM

Well I had 1.4 and 1.48 in the same folder compressed so I decompressed 1.48 to make sure that's the one it was running
I'm pretty sure I'm running 1.48 though.

I'm in Canada

edit: So far I'm running at 100% but only started it a few minutes ago.

On another note, my 4870 is running at 85-86mh/s stable.

edit2: after making sure I have 1.48, I'm still getting about 4-5%

edit3: After a bit more tweeking, I now have my 4870 up to 88-89mh/s. Sweeeeeeet

So, after doing that, my rejected is up to 23%.

All I did was turn on phatk. I had fastloop on before too when I was getting 4%. I've since turned both off and I'll look into both to see what exactly they do. Ah being a nub.

Fastloop: the fast loop argument for Phoenix. Can possibly increase mining speed if enabled.
phatk: uses the phatk kernel, optimization for HD58xx series only I think? You MUST have phatk already inside the kernels folder.

I took out all flags (bfi_int vectors worksize=128) and now mh/s is back up to 89. Before taking out those flags I was at 85mh/s with 10% rejected.

Still getting 8.5% rejected

edit: Just turned off fastloop, currently have 13 accepted and 0 rejected while still getting 89mh/s. Will let it run for a while like this.

annnnnd same issue. 11% rejected as of now.

i have 2 video cards, 6990 and 4870x2. on the 6990 i get 1% rejected and on the 4870x2 i get 90% rejected.
what am i doing wrong?
im starting the 6990 with this:

./phoenix.py -u http://XXXX:[email protected]:8080/ -k poclbm Device=0 VECTORS AGGRESSION=13 WORKSIZE=128 BFI_INT FASTLOOP=false

and i start the 4870x2 with this:

./phoenix.py -u http://XXXX:[email protected]:8080/ -k poclbm Device=2 AGGRESSION=13 WORKSIZE=256

please help:)
thanks.

Wrong thread!

-

As you may have noticed, Bitcoins.lc is down. The pool however, IS NOT! So don't freak out and switch pool. Everything is juuust fine Wink

http://twitter.com/#!/BitcoinsLC

why wrong thread? people are reporting on this thread that they are getting to many rejection.
im still mining on this pool and have checked their twitter.

pandemic

sr. member

Activity: 434

Merit: 250

Check if it's better now
I made some changes...

7.94% rejected since you posted

Slasklitta

newbie

Activity: 53

Merit: 0

Quote from: darkpandora on June 12, 2011, 02:25:21 PM

Well I had 1.4 and 1.48 in the same folder compressed so I decompressed 1.48 to make sure that's the one it was running
I'm pretty sure I'm running 1.48 though.

I'm in Canada

edit: So far I'm running at 100% but only started it a few minutes ago.

On another note, my 4870 is running at 85-86mh/s stable.

edit2: after making sure I have 1.48, I'm still getting about 4-5%

edit3: After a bit more tweeking, I now have my 4870 up to 88-89mh/s. Sweeeeeeet

So, after doing that, my rejected is up to 23%.

All I did was turn on phatk. I had fastloop on before too when I was getting 4%. I've since turned both off and I'll look into both to see what exactly they do. Ah being a nub.

Fastloop: the fast loop argument for Phoenix. Can possibly increase mining speed if enabled.
phatk: uses the phatk kernel, optimization for HD58xx series only I think? You MUST have phatk already inside the kernels folder.

I took out all flags (bfi_int vectors worksize=128) and now mh/s is back up to 89. Before taking out those flags I was at 85mh/s with 10% rejected.

Still getting 8.5% rejected

edit: Just turned off fastloop, currently have 13 accepted and 0 rejected while still getting 89mh/s. Will let it run for a while like this.

annnnnd same issue. 11% rejected as of now.

i have 2 video cards, 6990 and 4870x2. on the 6990 i get 1% rejected and on the 4870x2 i get 90% rejected.
what am i doing wrong?
im starting the 6990 with this:

./phoenix.py -u http://XXXX:[email protected]:8080/ -k poclbm Device=0 VECTORS AGGRESSION=13 WORKSIZE=128 BFI_INT FASTLOOP=false

and i start the 4870x2 with this:

./phoenix.py -u http://XXXX:[email protected]:8080/ -k poclbm Device=2 AGGRESSION=13 WORKSIZE=256

please help:)
thanks.

Wrong thread!

-

As you may have noticed, Bitcoins.lc is down. The pool however, IS NOT! So don't freak out and switch pool. Everything is juuust fine Wink

http://twitter.com/#!/BitcoinsLC

darkpandora

member

Activity: 98

Merit: 10

Well I had 1.4 and 1.48 in the same folder compressed so I decompressed 1.48 to make sure that's the one it was running
I'm pretty sure I'm running 1.48 though.

I'm in Canada

edit: So far I'm running at 100% but only started it a few minutes ago.

On another note, my 4870 is running at 85-86mh/s stable.

edit2: after making sure I have 1.48, I'm still getting about 4-5%

edit3: After a bit more tweeking, I now have my 4870 up to 88-89mh/s. Sweeeeeeet

So, after doing that, my rejected is up to 23%.

All I did was turn on phatk. I had fastloop on before too when I was getting 4%. I've since turned both off and I'll look into both to see what exactly they do. Ah being a nub.

Fastloop: the fast loop argument for Phoenix. Can possibly increase mining speed if enabled.
phatk: uses the phatk kernel, optimization for HD58xx series only I think? You MUST have phatk already inside the kernels folder.

I took out all flags (bfi_int vectors worksize=128) and now mh/s is back up to 89. Before taking out those flags I was at 85mh/s with 10% rejected.

Still getting 8.5% rejected

edit: Just turned off fastloop, currently have 13 accepted and 0 rejected while still getting 89mh/s. Will let it run for a while like this.

annnnnd same issue. 11% rejected as of now.

i have 2 video cards, 6990 and 4870x2. on the 6990 i get 1% rejected and on the 4870x2 i get 90% rejected.
what am i doing wrong?
im starting the 6990 with this:

./phoenix.py -u http://XXXX:[email protected]:8080/ -k poclbm Device=0 VECTORS AGGRESSION=13 WORKSIZE=128 BFI_INT FASTLOOP=false

and i start the 4870x2 with this:

./phoenix.py -u http://XXXX:[email protected]:8080/ -k poclbm Device=2 AGGRESSION=13 WORKSIZE=256

please help:)
thanks.

Jine

sr. member

Activity: 403

Merit: 250

Check if it's better now
I made some changes...

pandemic

sr. member

Activity: 434

Merit: 250

Well I had 1.4 and 1.48 in the same folder compressed so I decompressed 1.48 to make sure that's the one it was running
I'm pretty sure I'm running 1.48 though.

I'm in Canada

edit: So far I'm running at 100% but only started it a few minutes ago.

On another note, my 4870 is running at 85-86mh/s stable.

edit2: after making sure I have 1.48, I'm still getting about 4-5%

edit3: After a bit more tweeking, I now have my 4870 up to 88-89mh/s. Sweeeeeeet

So, after doing that, my rejected is up to 23%.

All I did was turn on phatk. I had fastloop on before too when I was getting 4%. I've since turned both off and I'll look into both to see what exactly they do. Ah being a nub.

Fastloop: the fast loop argument for Phoenix. Can possibly increase mining speed if enabled.
phatk: uses the phatk kernel, optimization for HD58xx series only I think? You MUST have phatk already inside the kernels folder.

I took out all flags (bfi_int vectors worksize=128) and now mh/s is back up to 89. Before taking out those flags I was at 85mh/s with 10% rejected.

Still getting 8.5% rejected

edit: Just turned off fastloop, currently have 13 accepted and 0 rejected while still getting 89mh/s. Will let it run for a while like this.

annnnnd same issue. 11% rejected as of now.

pandemic

sr. member

Activity: 434

Merit: 250