Hello. I'm using EWBF's CUDA Zcash miner 0.3.3b but when I start the miner it closes immediately. It was working fine on that PC with 2 1080ti and after it gave me 0 sols I closed the miner and since then I cannot start it.
I've reinstalled drivers, downloaded a new copy of the miner, but it is the same problem - the miner opens and closes after a few seconds.
Topic: EWBF's CUDA Zcash miner - page 152. (Read 2164327 times)
In the start.bat , how to restart PC if miner has problem because restart miner doesn't work?
well the pc dosnt restart it'selve and there is normally no need to.the miner will reconnect if it looses connection
use --eexit 1 to close the miner if it cannot restart the workers and run the start.bat again
:restart
Timeout /t 30
miner --server eu1-zcash.flypool.org --user t1cA38xyUxJRDdQYacD6x7UUL8nyjTfKeo1.GigaGamer --pass x --port 3333 --eexit 3 --solver 0 --log 2 --logfile ZCASH.%date:~6,4%%date:~3,2%%date:~0,2%.ewbf.log --fee 2 --pec
ping 127.0.0.1 > nul
goto :restart
Hello, everyone! Guys, can you please help me out? I'm new and can't get my miner work properly.
All I want is miner to restart itself when its glitched or error occurred and miner stopped mining.
My miner setup:
miner --cuda_devices 0 1 2 3 --pec --server equihash.eu.nicehash.com --user wallet --pass x --port 3357 --log 2 --eexit 3
Wheres mistake? (
All I want is miner to restart itself when its glitched or error occurred and miner stopped mining.
My miner setup:
miner --cuda_devices 0 1 2 3 --pec --server equihash.eu.nicehash.com --user wallet --pass x --port 3357 --log 2 --eexit 3
Wheres mistake? (
Last parameter should be --exit 3, looks like you have an extra e?
miner --server equihash.eu.nicehash.com --user wallet.rigname --pass x --port 3357 --log 2 --eexit 3 --cuda_devices 0 1 2 3 --pec
When working right, --eexit takes like 30 minutes to restart.
it closing miner and after that in 30 minutes is should load it back? or it should close and start it immediately?
Right now my miner closing in like 5 minutes after error and does not start after.
Well I have not witnessed it live cause it always happened while I was away but I could tell from the pool's chart
that it took half an hour to start mining again. Notice that I speak to the past cause it's been many weeks if not months
that my rigs have stalled. Once you find the right settings for your rig and that you stop playing with it, you will see that the miner
is really stable. I for myself find that under windows restarting my rigs every 2 days or so is a good thing to avoid the rig to slow down.
You can also use the code below to monitor and restart the rig
:restart
Timeout /t 30
miner --server eu1-zcash.flypool.org --user t1cA38xyUxJRDdQYacD6x7UUL8nyjTfKeo1.GigaGamer --pass x --port 3333 --eexit 3 --solver 0 --log 2 --logfile ZCASH.%date:~6,4%%date:~3,2%%date:~0,2%.ewbf.log --fee 2 --pec
ping 127.0.0.1 > nul
goto :restart
Hello, everyone! Guys, can you please help me out? I'm new and can't get my miner work properly.
All I want is miner to restart itself when its glitched or error occurred and miner stopped mining.
My miner setup:
miner --cuda_devices 0 1 2 3 --pec --server equihash.eu.nicehash.com --user wallet --pass x --port 3357 --log 2 --eexit 3
Wheres mistake? (
All I want is miner to restart itself when its glitched or error occurred and miner stopped mining.
My miner setup:
miner --cuda_devices 0 1 2 3 --pec --server equihash.eu.nicehash.com --user wallet --pass x --port 3357 --log 2 --eexit 3
Wheres mistake? (
Last parameter should be --exit 3, looks like you have an extra e?
miner --server equihash.eu.nicehash.com --user wallet.rigname --pass x --port 3357 --log 2 --eexit 3 --cuda_devices 0 1 2 3 --pec
When working right, --eexit takes like 30 minutes to restart.
it closing miner and after that in 30 minutes is should load it back? or it should close and start it immediately?
Right now my miner closing in like 5 minutes after error and does not start after.
In the start.bat , how to restart PC if miner has problem because restart miner doesn't work?
well the pc dosnt restart it'selve and there is normally no need to.the miner will reconnect if it looses connection
use --eexit 1 to close the miner if it cannot restart the workers and run the start.bat again
Hi thereWhat are the best settings for 1070 Pallit jetstream or gamerock flashed to gamerock premium?
I know there are many experimentators here with great experience. I have 450 sol and 170W. And that is not good result.
Notice: Pair of my cards cant handle flashed core clock with stable mining. It hangs and I forced to reduce core clock -30 to do it stable
Please give me advice and recommend settings for afterburner
In the start.bat , how to restart PC if miner has problem because restart miner doesn't work?
well the pc dosnt restart it'selve and there is normally no need to.the miner will reconnect if it looses connection
use --eexit 1 to close the miner if it cannot restart the workers and run the start.bat again
In the start.bat , how to restart PC if miner has problem because restart miner doesn't work?
can't find any shares on coinotron.what's wrong?
I'm getting an error when i run my command in the terminal from the folder
"bash: permission denied"
./miner --server us1-zcash.flypool.org:3333 --user tmQiBF7UyGTDZk3XKEjg7eBJe3uUW7VYWia. --pass x --port 3333 --cuda_devices 0 1
what am i missing?
the folder only has a miner executable and a help file
i'm at a loss on what's wrong
help appreciated
this is linux running nvidia 980 classifieds
"bash: permission denied"
./miner --server us1-zcash.flypool.org:3333 --user tmQiBF7UyGTDZk3XKEjg7eBJe3uUW7VYWia. --pass x --port 3333 --cuda_devices 0 1
what am i missing?
the folder only has a miner executable and a help file
i'm at a loss on what's wrong
help appreciated
this is linux running nvidia 980 classifieds
Dude, I am new to it, I managed to run the miner file on Linux x64 but I do not know where to edit the server ip and wallet address. There is only 2 file in the download, 1 is help and 1 is miner. Can some1 please teach me how to edit my wallet address?
Your download is incomplete. There should 10 files. You mod one of the .bat files.
Dude, I am new to it, I managed to run the miner file on Linux x64 but I do not know where to edit the server ip and wallet address. There is only 2 file in the download, 1 is help and 1 is miner. Can some1 please teach me how to edit my wallet address?
Hi, I have problem with this miner, sometime it's stuck in 0 sol how to auto restart the miner or PC if it happens?
What is the easiest way to use the api to monitor it?
Thank you
What is the easiest way to use the api to monitor it?
Thank you
Hey dudes, trying to help a buddy configure a 1060 rig with three cards but he's having some trouble getting the second and third cards working.
Specs:
OS - Win7 64
Mobo - M5A97 LE R2.0
PSU - Corsair 1200W
Miner - 0.3.3b
Not sure on the drivers
I've tried to have him set --cuda_devices to 1 and 2 exclusively to test the cards individually and the miner crashed both times. Only card 0 is working. Also tried the standard switch the ports around, change risers, reinstall driver, etc. to no avail. Any advice? Are there any config, Windows or BIOS-specific settings that might need to be tweaked to get this working? Any advice is much appreciated.
Specs:
OS - Win7 64
Mobo - M5A97 LE R2.0
PSU - Corsair 1200W
Miner - 0.3.3b
Not sure on the drivers
I've tried to have him set --cuda_devices to 1 and 2 exclusively to test the cards individually and the miner crashed both times. Only card 0 is working. Also tried the standard switch the ports around, change risers, reinstall driver, etc. to no avail. Any advice? Are there any config, Windows or BIOS-specific settings that might need to be tweaked to get this working? Any advice is much appreciated.
I guess that you used #1,2,3 slot. I believe That slot 1 is 1st GPU and that 2nd GPU would be 4th slot (black one) and the 3rd GPU, one of the 1x slot. Mosty the third one.
SO slot 1,4,3 I would try. (or 1,4,2)
Also check in Device Manager if all cards are detected and all drivers installed. ()
Hello, everyone! Guys, can you please help me out? I'm new and can't get my miner work properly.
All I want is miner to restart itself when its glitched or error occurred and miner stopped mining.
My miner setup:
miner --cuda_devices 0 1 2 3 --pec --server equihash.eu.nicehash.com --user wallet --pass x --port 3357 --log 2 --eexit 3
Wheres mistake? (
All I want is miner to restart itself when its glitched or error occurred and miner stopped mining.
My miner setup:
miner --cuda_devices 0 1 2 3 --pec --server equihash.eu.nicehash.com --user wallet --pass x --port 3357 --log 2 --eexit 3
Wheres mistake? (
Last parameter should be --exit 3, looks like you have an extra e?
miner --server equihash.eu.nicehash.com --user wallet.rigname --pass x --port 3357 --log 2 --eexit 3 --cuda_devices 0 1 2 3 --pec
When working right, --eexit takes like 30 minutes to restart.
i figured it out
how do i attatch a photo here...
screw it ill imgur it
http://imgur.com/CXSmwvv
their EXAMPLE has the port after teh server
it wont run like that
i REMOVED that and its working now
Hello, everyone! Guys, can you please help me out? I'm new and can't get my miner work properly.
All I want is miner to restart itself when its glitched or error occurred and miner stopped mining.
My miner setup:
miner --cuda_devices 0 1 2 3 --pec --server equihash.eu.nicehash.com --user wallet --pass x --port 3357 --log 2 --eexit 3
Wheres mistake? (
All I want is miner to restart itself when its glitched or error occurred and miner stopped mining.
My miner setup:
miner --cuda_devices 0 1 2 3 --pec --server equihash.eu.nicehash.com --user wallet --pass x --port 3357 --log 2 --eexit 3
Wheres mistake? (
Last parameter should be --exit 3, looks like you have an extra e?
miner --server equihash.eu.nicehash.com --user wallet.rigname --pass x --port 3357 --log 2 --eexit 3 --cuda_devices 0 1 2 3 --pec
When working right, --eexit takes like 30 minutes to restart.
whats up dudes, im trying to get my first mining rig going,
currently trying to test this on windows 10 64 bit system on my personal pc
wanted to check out zcash
using my best menatal fortitude ive gotten so far as
downloaded the file Zec miner 0.3.3b
, extracted,
and created a .bat
but im not sure what other settings to punch in besides my username which was the address i got off of poloniex.com
miner.exe --server us1-zcash.flypool.org:3333 --user t1R2urSb48RtF8C3tUR3KaSrzhHJzAb53hy.rig1 --pass x --port 3333 --cuda_devices 0 1 2
currently trying to test this on windows 10 64 bit system on my personal pc
wanted to check out zcash
using my best menatal fortitude ive gotten so far as
downloaded the file Zec miner 0.3.3b
, extracted,
and created a .bat
but im not sure what other settings to punch in besides my username which was the address i got off of poloniex.com
miner.exe --server us1-zcash.flypool.org:3333 --user t1R2urSb48RtF8C3tUR3KaSrzhHJzAb53hy.rig1 --pass x --port 3333 --cuda_devices 0 1 2
Hey dudes, trying to help a buddy configure a 1060 rig with three cards but he's having some trouble getting the second and third cards working.
Specs:
OS - Win7 64
Mobo - M5A97 LE R2.0
PSU - Corsair 1200W
Miner - 0.3.3b
Not sure on the drivers
I've tried to have him set --cuda_devices to 1 and 2 exclusively to test the cards individually and the miner crashed both times. Only card 0 is working. Also tried the standard switch the ports around, change risers, reinstall driver, etc. to no avail. Any advice? Are there any config, Windows or BIOS-specific settings that might need to be tweaked to get this working? Any advice is much appreciated.
Specs:
OS - Win7 64
Mobo - M5A97 LE R2.0
PSU - Corsair 1200W
Miner - 0.3.3b
Not sure on the drivers
I've tried to have him set --cuda_devices to 1 and 2 exclusively to test the cards individually and the miner crashed both times. Only card 0 is working. Also tried the standard switch the ports around, change risers, reinstall driver, etc. to no avail. Any advice? Are there any config, Windows or BIOS-specific settings that might need to be tweaked to get this working? Any advice is much appreciated.
Hello, everyone! Guys, can you please help me out? I'm new and can't get my miner work properly.
All I want is miner to restart itself when its glitched or error occurred and miner stopped mining.
My miner setup:
miner --cuda_devices 0 1 2 3 --pec --server equihash.eu.nicehash.com --user wallet --pass x --port 3357 --log 2 --eexit 3
Wheres mistake? (
All I want is miner to restart itself when its glitched or error occurred and miner stopped mining.
My miner setup:
miner --cuda_devices 0 1 2 3 --pec --server equihash.eu.nicehash.com --user wallet --pass x --port 3357 --log 2 --eexit 3
Wheres mistake? (
Last parameter should be --exit 3, looks like you have an extra e?
Hello, everyone! Guys, can you please help me out? I'm new and can't get my miner work properly.
All I want is miner to restart itself when its glitched or error occurred and miner stopped mining.
My miner setup:
miner --cuda_devices 0 1 2 3 --pec --server equihash.eu.nicehash.com --user wallet --pass x --port 3357 --log 2 --eexit 3
Wheres mistake? (
All I want is miner to restart itself when its glitched or error occurred and miner stopped mining.
My miner setup:
miner --cuda_devices 0 1 2 3 --pec --server equihash.eu.nicehash.com --user wallet --pass x --port 3357 --log 2 --eexit 3
Wheres mistake? (
Jump to: