Topic: [GROUP BUY WORLDWIDE]BTMine v1 Miner 200GH/s BTC 2.4 - page 28. (Read 97274 times)

Its because you set the fan speed at 20%. Remove --avalon-fan 20 from "More Options".

Got my 2 today that I paid in BTC.
Neither has the PSU I paid for, even after being this late. I will be reopening my paypal dispute, this is unacceptable.

I finally got it hashing idk how.

one question tho.

fan starts at 100% then cgminer loads; the fan speed decrease and then it goes to 20% i think, but temp is 70°+; is it normal ? I assume it's not since i setup the temp overheat @ 70.

Any help ?

 

btw what r the max safe temp for those chips ? Is there a way to cut the miner if it's too hot ? because I had to stop it by unpluggin it since it were going over 70°.

If the fan half spins and stops then you may be trying to use a PSU that does not have enough amps. You might have fried your PSU. It may still turn on but with any serious power draw it auto shuts off.

+1 on the do no electrocute yourself. You can always sell it as is on the forum or ebay.

Reading through all your post is really starting to scare me. Please don't electrocute your self. I don't want to read the yahoo news post about you on the front page with the Headlines GUY that had no clue what he was doing Electrocutes him self trying to setup a bitcoin machine!!!

Okay so do you have a pic of the other end. I am still running the PSU that came with it on the other side. I'm not sure if I'm putting the plugs in the right place. I'm not even sure what the plugs do. All I know is that the fan would half spin then stop. Anyone else that provided their own PSU have a answer for this?

Dunno about zetacoin

But try this:

Host: stratum+tcp://stratum.mining.eligius.st:3334
Worker: YourWalletAddress
Password: xxx

mine is stuck at customs...
seems they did not put an invoice

I ordered a new network card from BTmine. I'll mine with my laptop for now. Does anyone know what changes I'd make to switch back to the TPlink?

On ckolvas' web repository:  http://ck.kolivas.org/apps/cgminer/avalon/20131229/

it's a firmware pb I have not your AVALON CHIP in my list.

Please send me a working backup.

PING openwrt.org (78.24.191.177): 56 data bytes
64 bytes from 78.24.191.177: seq=0 ttl=44 time=103.630 ms
64 bytes from 78.24.191.177: seq=1 ttl=44 time=103.390 ms
64 bytes from 78.24.191.177: seq=2 ttl=44 time=100.186 ms
64 bytes from 78.24.191.177: seq=3 ttl=44 time=103.919 ms
64 bytes from 78.24.191.177: seq=4 ttl=44 time=108.180 ms

--- openwrt.org ping statistics ---
5 packets transmitted, 5 packets received, 0% packet loss
round-trip min/avg/max = 100.186/103.861/108.180 ms




pool config seems ok.

Has anyone had any success overclocking in increments smaller than 100?  For example, 1410?  I don't want to jump to 1500 right away since people are reporting blown SMD fuses at 1500.  I've tried 1410, but it doesn't seem like that and only hashes 8-10 GH/s total or so...




twib2, where are you downloading firmware images from?



Different topic:


I've noticed that cgminer won't start if you don't have any valid pools specified.  For example, I mistakenly entered stratum+tcp://mining.bitcoin.cz:3333 instead of stratum+tcp://stratum.bitcoin.cz:3333, and the cgminer API log would keep getting stuck on "Socket connect failed: Connection refused" until I figured it out.  "Socket connect failed: Connection refused" just means that cgminer isn't starting properly.  If all else fails, try the reset button on the TP-link board, or there is also a factory reset option in the UI, which I think resets the IP to 192.168.0.100, and you'll have to re-enter the chip frequency, chip count, etc.  If you still really really need a configuration backup of a working machine, PM me (not sharing publicly since the configuration backup has my worker info).

If you're running into problems because you want to get wifi working, you're on your own.  I'd recommend sticking to hardwired for now.

I have 1 unit with 0rpm info all cables connected. Will investigate more in future. In the same unit --avalon-fan goes reverse.

Cool, matches what I'm seeing, though I'm using the newest ckolvas firmware running 3.9.0 cgminer.  Note that my firmware doesn't give me fan speeds, but I'm not sure if it's my unit or the alternate firmware, but because of that I'd not recommend upgrading firmware - no need.

1hour 15mins with 1500 OC temps under control and unit has 2x 1200w psu. Dont know how much it drains frogot the meter.

Is it connected to internet? Try "Network" -> "Diagnostics" -> "Ping".
If its connected, double check the pool info. Don't leave the password blank even if the pool doesnt require password.

If you remove PWM signal cable (yellow or blue) from the fan and leave red and black.
It should run at full speed.

Maybe starts form value 20 not 0 and it could be reverse so 80 is 20% fan speed. After setting value give it minute or 2 to setup.

https://en.bitcoin.it/wiki/Avalon
--avalon-fan  Set fanspeed percentage for avalon, single value or range (default: 20-100)

I have a unit that works reverse:

--avalon-fan 80 = 20% fan speed if i put value 20 it's 80% fan speed.
other units
--avalon-fan 20 = 20% fan speed

Thanks, I tried both - 0 seems to spin the Fan2 @ '240' and Fan3 @ '480'. The other miners show '2880' for both fans. Any ideas on how to make these fans go all the time?