Would it be possible to use p2p pools; im thinking not with the proxy?
If the p2p pool is stratum, then yes.
Topic: [GUIDE] How to rent your rig on LEASERIG.NET - Scrypt & SHA256 - page 7. (Read 33446 times)
If the p2p pool is stratum, then yes.
Would it be possible to use p2p pools; im thinking not with the proxy?
Does anyone know how to setup antminers using the advanced method...I am stuck trying to do this api stuff.
I have not tried it as the LRP is working out for me, but check out the following link. It tells you were to make the API config changes.
https://bitcointalksearch.org/topic/antminer-s1-privileged-api-499837
We can keep the pool.conf and the run.bat, right? ^^
Yep worked for me!
We can keep the pool.conf and the run.bat, right? ^^
Looks like there are no issues with eligius pool anymore. Just make sure you use latest 0.05d version of LRP.
Worked a treat - thanks guys. No more disconnects either! Edit, drops every 20/30 secs
M
M
Just testing new version... Wait 5min.
EDIT: Ok, looks like it is OK now, upgrade please.
Quote
v0.05d
- fixed ping issue from v0.05c
- fixed ping issue from v0.05c
Working flawlessly! Fantastic job!
Worked a treat - thanks guys. No more disconnects either! Edit, drops every 20/30 secs
M
M
Just testing new version... Wait 5min.
EDIT: Ok, looks like it is OK now, upgrade please.
Quote
v0.05d
- fixed ping issue from v0.05c
- fixed ping issue from v0.05c
Worked a treat - thanks guys. No more disconnects either! Edit, drops every 20/30 secs
M
M
Having a bit of an nightmare setting this up. I have my GPU rig mining away though the speed isn't measure (Method A) So then I set up:
and added 7777 to the proxy run.bat.
I've turned win firewall off to eliminate that.
I keep getting the error:
HELP?!
Disconnects from the proxy too even without the API commands... Could be similar issue to above this post?
Quote
--api-listen --api-allow W:89.212.242.33 --api-port 7777
and added 7777 to the proxy run.bat.
I've turned win firewall off to eliminate that.
I keep getting the error:
Quote
WARNING: cgminer API (127.0.0.1:7777) Closing connection - is IP allowed?
HELP?!
Disconnects from the proxy too even without the API commands... Could be similar issue to above this post?
Use localhost: 127.0.0.1 as IP address - should work.
Yes.
New LRP is being tested as we speak. Prepare to upgrade it again.
Having a bit of an nightmare setting this up. I have my GPU rig mining away though the speed isn't measure (Method A) So then I set up:
and added 7777 to the proxy run.bat.
I've turned win firewall off to eliminate that.
I keep getting the error:
HELP?!
Disconnects from the proxy too even without the API commands... Could be similar issue to above this post?
Quote
--api-listen --api-allow W:89.212.242.33 --api-port 7777
and added 7777 to the proxy run.bat.
I've turned win firewall off to eliminate that.
I keep getting the error:
Quote
WARNING: cgminer API (127.0.0.1:7777) Closing connection - is IP allowed?
HELP?!
Disconnects from the proxy too even without the API commands... Could be similar issue to above this post?
Use localhost: 127.0.0.1 as IP address - should work, assuming that LRP and cgminer run on the same machine.
Code:
--api-listen --api-allow W:127.0.0.1 --api-port 7777
The other IP mentioned in the guide is for the second connection type.
Having a bit of an nightmare setting this up. I have my GPU rig mining away though the speed isn't measure (Method A) So then I set up:
and added 7777 to the proxy run.bat.
I've turned win firewall off to eliminate that.
I keep getting the error:
HELP?!
Disconnects from the proxy too even without the API commands... Could be similar issue to above this post?
Quote
--api-listen --api-allow W:89.212.242.33 --api-port 7777
and added 7777 to the proxy run.bat.
I've turned win firewall off to eliminate that.
I keep getting the error:
Quote
WARNING: cgminer API (127.0.0.1:7777) Closing connection - is IP allowed?
HELP?!
Disconnects from the proxy too even without the API commands... Could be similar issue to above this post?
I need a copy of the b proxy if c can't be fixed. I didn't keep a copy of it.
New LeaseRigProxy:
Quote
v0.5c
- improved compatibility with some stratum pools
- sending "ping" data to keep connection alive
- improved compatibility with some stratum pools
- sending "ping" data to keep connection alive
Just upgraded to this version and although it appeared to be working ok hashing, submitting shares and getting the speeds from the api, the leaserigs site was reporting it as OFF
Gone back to v0.5a and it's working again.
This is on a KNC Jupiter in case it's important.
Will take a look into it. BTW, how long did you wait before switching back?
I am trying the c version now and also have the same problem. My ants on the site are constantly switching from OFF to full speed. Proxy log on my end shows no problems.. speed logging from API seems to be working.
Anyone else have a buyer who is connected to btc.mupool.com? I'm using the proxy with the 's' setting... and leaserig.net is reporting very low hashrates. For example my rigs are running at 393gh and 394gh... and leaserig is reporting 256gh and 245gh 
Ideas?
Ideas?I would say bad luck. Except if the pool is unstable and your rigs are constantly reconnecting to it.
What was weird was I never saw a rig disconnect or pool disconnect.... just accepted shares flying by on the proxy...
Bad luck then.
New LeaseRigProxy:
Quote
v0.5c
- improved compatibility with some stratum pools
- sending "ping" data to keep connection alive
- improved compatibility with some stratum pools
- sending "ping" data to keep connection alive
Just upgraded to this version and although it appeared to be working ok hashing, submitting shares and getting the speeds from the api, the leaserigs site was reporting it as OFF
Gone back to v0.5a and it's working again.
This is on a KNC Jupiter in case it's important.
Will take a look into it. BTW, how long did you wait before switching back?
New LeaseRigProxy:
Quote
v0.5c
- improved compatibility with some stratum pools
- sending "ping" data to keep connection alive
- improved compatibility with some stratum pools
- sending "ping" data to keep connection alive
Just upgraded to this version and although it appeared to be working ok hashing, submitting shares and getting the speeds from the api, the leaserigs site was reporting it as OFF
Gone back to v0.5a and it's working again.
This is on a KNC Jupiter in case it's important.
Anyone else have a buyer who is connected to btc.mupool.com? I'm using the proxy with the 's' setting... and leaserig.net is reporting very low hashrates. For example my rigs are running at 393gh and 394gh... and leaserig is reporting 256gh and 245gh Ideas?
Ideas?I would say bad luck. Except if the pool is unstable and your rigs are constantly reconnecting to it.
What was weird was I never saw a rig disconnect or pool disconnect.... just accepted shares flying by on the proxy...
Does anyone know how to setup antminers using the advanced method...I am stuck trying to do this api stuff.
I only use the proxy with mine, but best guess is you'll need to edit
/etc/init.d/cgminer
there is a line that starts
PARAMS="AOPTIONS....
in there you will need to insert the commands you want to add.
Does anyone know how to setup antminers using the advanced method...I am stuck trying to do this api stuff.
Jump to: