MINE ON WITH 16V AND KANO-SAN!
right?!?! time for some blocks!
Topic: KanoPool kano.is lowest 0.9% fee 🐈 since 2014 - Worldwide - 2432 blocks - page 37. (Read 5352067 times)
June 24, 2019, 10:04:34 AM
right?!?! time for some blocks!
June 24, 2019, 08:27:02 AM
MINE ON WITH 16V AND KANO-SAN!
June 24, 2019, 02:30:45 AM
"powerminingshop" + 5G
Hm.. Are you legitimately using that service and that shipping container or just advertising? I remember hearing about them.
June 23, 2019, 06:00:13 PM
I point it your pool https://powerminingshop.com/
Wish me luck! I don't have working ASIC at this moment
We have 5G main city area, its good to connect in mobile interface.
Wish me luck! I don't have working ASIC at this moment
We have 5G main city area, its good to connect in mobile interface.
June 19, 2019, 08:11:36 PM
If yaw playing around with hash rates to move it up and down, the easiest way to think of the "Workers->Shift Graph" is like a tank of water (with unlimited space)
The red 5Nd line shows how full (the green area) is at the moment.
The area under that red 5Nd line is the equivalent of all the blue line ups and downs across the green area.
The left side of the red 5Nd line (where the green area starts) is what is leaking out each shift.
The right side of the red 5Nd line is what you add each shift.
Each shift: if what leaves on the left is lower than what adds on the right, the red 5Nd line moves up.
If what leaves on the left is higher than what adds on the right, the red 5Nd line moves down.
This is exactly what the 5Nd is doing when we find a block.
Adding up all your shifts for the last 5Nd, to determine your share of the reward.
The red 5Nd line shows how full (the green area) is at the moment.
The area under that red 5Nd line is the equivalent of all the blue line ups and downs across the green area.
The left side of the red 5Nd line (where the green area starts) is what is leaking out each shift.
The right side of the red 5Nd line is what you add each shift.
Each shift: if what leaves on the left is lower than what adds on the right, the red 5Nd line moves up.
If what leaves on the left is higher than what adds on the right, the red 5Nd line moves down.
This is exactly what the 5Nd is doing when we find a block.
Adding up all your shifts for the last 5Nd, to determine your share of the reward.
June 19, 2019, 07:52:49 PM
Cool, thanks for answering. June 19, 2019, 06:51:44 PM
So, I have been mining on Kano with a T9+ and learning this 5Nd thing for a month now and was not even close to getting to the 10.5TH ramp up; I went ahead and "helped it" with a 2nd T9+ and a Bitfily B1+ (Total of 34TH), now my Shift Graph shows roughly the same as the single miner.
Does this mean at next payout I can expect the "full" share of the single 10.5TH miner?
Is this way of ramping up quickly ok?
Does this mean at next payout I can expect the "full" share of the single 10.5TH miner?
Is this way of ramping up quickly ok?
this effect is the same - as you were ramping up to 10.5 th/s you now have to ramp up to 34 th/s but yes, what your shift graph shows as your average should be what you get paid for.
June 19, 2019, 04:47:01 PM
So, I have been mining on Kano with a T9+ and learning this 5Nd thing for a month now and was not even close to getting to the 10.5TH ramp up; I went ahead and "helped it" with a 2nd T9+ and a Bitfily B1+ (Total of 34TH), now my Shift Graph shows roughly the same as the single miner.
Does this mean at next payout I can expect the "full" share of the single 10.5TH miner?
Is this way of ramping up quickly ok?
Does this mean at next payout I can expect the "full" share of the single 10.5TH miner?
Is this way of ramping up quickly ok?
This way of ramping up quickly is ok, but it's still going to take you awhile to get up to that 10.5TH average. But, like you said, you'll be getting there quicker than by just mining with the original 10.5TH machine.
June 19, 2019, 02:23:44 PM
Any relation to this business? Most likely not, i would guess.
https://www.engadget.com/2019/06/19/kano-pc-windows-10-coding-computer/
https://www.engadget.com/2019/06/19/kano-pc-windows-10-coding-computer/
Quote
Kano is graduating from Raspberry Pi boards. Today, the company is announcing a partnership with Microsoft and unveiling its first build-it-yourself computer that officially runs Windows 10.
June 19, 2019, 08:49:30 AM
Just wanted to share a bit of good news that happened to me today (and for anyone that has an old Antminer R4) this info could potentially help.
I had an unexpected good event happen on one of my miners today - my old Antminer R4 - you see a lot of them processing at half rate (4THs instead of 8THs) because one of the two hash boards 'goes bad'. Well that happened to me over 8 moths ago on my R4 and today after a power brown-out my other miners never missed a beat and stayed online working away while the R4 appeared to be working (with one board @ 4THs which it has been for the last 8 months and many hardware reboots) but on Kano.is was showing it wasn't processing any shares and hadn't been for over 19 hours. Usually I do a HARDWARE reset by shutting off the main power supply and turning it back on & that resolves the issue. However this time I instead forced a soft reboot in the Miner Configuration Web GUI, and to my surprise - WOW - the 2nd hashing board CAME BACK TO LIFE! Now the old R4 is back to processing at over 8THs! Just thought I'd share some good mining news. Have a good one & mine on with KANO!
I had an unexpected good event happen on one of my miners today - my old Antminer R4 - you see a lot of them processing at half rate (4THs instead of 8THs) because one of the two hash boards 'goes bad'. Well that happened to me over 8 moths ago on my R4 and today after a power brown-out my other miners never missed a beat and stayed online working away while the R4 appeared to be working (with one board @ 4THs which it has been for the last 8 months and many hardware reboots) but on Kano.is was showing it wasn't processing any shares and hadn't been for over 19 hours. Usually I do a HARDWARE reset by shutting off the main power supply and turning it back on & that resolves the issue. However this time I instead forced a soft reboot in the Miner Configuration Web GUI, and to my surprise - WOW - the 2nd hashing board CAME BACK TO LIFE! Now the old R4 is back to processing at over 8THs! Just thought I'd share some good mining news. Have a good one & mine on with KANO!
I think i saw that happening to me as well once last year, and i think i did in fact just reboot the controller from console.
If you use the firmware from Dec 2018, it should do 8.5THs, or at least it did with my 8T model (600ish mhz boards).
June 19, 2019, 08:30:26 AM
So, I have been mining on Kano with a T9+ and learning this 5Nd thing for a month now and was not even close to getting to the 10.5TH ramp up; I went ahead and "helped it" with a 2nd T9+ and a Bitfily B1+ (Total of 34TH), now my Shift Graph shows roughly the same as the single miner.
Does this mean at next payout I can expect the "full" share of the single 10.5TH miner?
Is this way of ramping up quickly ok?
Does this mean at next payout I can expect the "full" share of the single 10.5TH miner?
Is this way of ramping up quickly ok?
June 17, 2019, 10:53:47 PM
Just wanted to share a bit of good news that happened to me today (and for anyone that has an old Antminer R4) this info could potentially help.
I had an unexpected good event happen on one of my miners today - my old Antminer R4 - you see a lot of them processing at half rate (4THs instead of 8THs) because one of the two hash boards 'goes bad'. Well that happened to me over 8 moths ago on my R4 and today after a power brown-out my other miners never missed a beat and stayed online working away while the R4 appeared to be working (with one board @ 4THs which it has been for the last 8 months and many hardware reboots) but on Kano.is was showing it wasn't processing any shares and hadn't been for over 19 hours. Usually I do a HARDWARE reset by shutting off the main power supply and turning it back on & that resolves the issue. However this time I instead forced a soft reboot in the Miner Configuration Web GUI, and to my surprise - WOW - the 2nd hashing board CAME BACK TO LIFE! Now the old R4 is back to processing at over 8THs! Just thought I'd share some good mining news. Have a good one & mine on with KANO!
I had an unexpected good event happen on one of my miners today - my old Antminer R4 - you see a lot of them processing at half rate (4THs instead of 8THs) because one of the two hash boards 'goes bad'. Well that happened to me over 8 moths ago on my R4 and today after a power brown-out my other miners never missed a beat and stayed online working away while the R4 appeared to be working (with one board @ 4THs which it has been for the last 8 months and many hardware reboots) but on Kano.is was showing it wasn't processing any shares and hadn't been for over 19 hours. Usually I do a HARDWARE reset by shutting off the main power supply and turning it back on & that resolves the issue. However this time I instead forced a soft reboot in the Miner Configuration Web GUI, and to my surprise - WOW - the 2nd hashing board CAME BACK TO LIFE! Now the old R4 is back to processing at over 8THs! Just thought I'd share some good mining news. Have a good one & mine on with KANO!
nice and congrats! hope it stays running for you!
June 17, 2019, 10:42:20 PM
Just wanted to share a bit of good news that happened to me today (and for anyone that has an old Antminer R4) this info could potentially help.
I had an unexpected good event happen on one of my miners today - my old Antminer R4 - you see a lot of them processing at half rate (4THs instead of 8THs) because one of the two hash boards 'goes bad'. Well that happened to me over 8 moths ago on my R4 and today after a power brown-out my other miners never missed a beat and stayed online working away while the R4 appeared to be working (with one board @ 4THs which it has been for the last 8 months and many hardware reboots) but on Kano.is was showing it wasn't processing any shares and hadn't been for over 19 hours. Usually I do a HARDWARE reset by shutting off the main power supply and turning it back on & that resolves the issue. However this time I instead forced a soft reboot in the Miner Configuration Web GUI, and to my surprise - WOW - the 2nd hashing board CAME BACK TO LIFE! Now the old R4 is back to processing at over 8THs! Just thought I'd share some good mining news. Have a good one & mine on with KANO!
I had an unexpected good event happen on one of my miners today - my old Antminer R4 - you see a lot of them processing at half rate (4THs instead of 8THs) because one of the two hash boards 'goes bad'. Well that happened to me over 8 moths ago on my R4 and today after a power brown-out my other miners never missed a beat and stayed online working away while the R4 appeared to be working (with one board @ 4THs which it has been for the last 8 months and many hardware reboots) but on Kano.is was showing it wasn't processing any shares and hadn't been for over 19 hours. Usually I do a HARDWARE reset by shutting off the main power supply and turning it back on & that resolves the issue. However this time I instead forced a soft reboot in the Miner Configuration Web GUI, and to my surprise - WOW - the 2nd hashing board CAME BACK TO LIFE! Now the old R4 is back to processing at over 8THs! Just thought I'd share some good mining news. Have a good one & mine on with KANO!
June 17, 2019, 10:16:49 AM
is kano.is down? I cannot get the page to load.
**EDIT**
nvm - figures as soon as I post that it comes back up lol
There were network delays at the web server for a couple of minutes just after 14:00 UTC**EDIT**
nvm - figures as soon as I post that it comes back up lol
But they resolved themselves pretty quickly so I didn't have to find out what was going wrong.
Seemed to be all OK after that, but I guess you might have seen a hiccough after that caused by whatever caused it in the first place.
yea it was only a brief few minutes - just happened to be when I was trying to look at it
June 17, 2019, 10:08:56 AM
is kano.is down? I cannot get the page to load.
**EDIT**
nvm - figures as soon as I post that it comes back up lol
There were network delays at the web server for a couple of minutes just after 14:00 UTC**EDIT**
nvm - figures as soon as I post that it comes back up lol
But they resolved themselves pretty quickly so I didn't have to find out what was going wrong.
Seemed to be all OK after that, but I guess you might have seen a hiccough after that caused by whatever caused it in the first place.
June 17, 2019, 09:54:48 AM
All well for me
June 17, 2019, 09:53:30 AM
is kano.is down? I cannot get the page to load.
**EDIT**
nvm - figures as soon as I post that it comes back up lol
**EDIT**
nvm - figures as soon as I post that it comes back up lol
June 16, 2019, 12:18:49 PM
Like I said in Discord, if we get 3 blocks this weekend I'll go vegan for the rest of the month
1 down 2 to go...
1 down 2 to go...
June 16, 2019, 11:05:06 AM
16vV does it again! Thank you.
Thanks 16vV8! Another welcomed BLOCK PARTY
June 16, 2019, 07:54:07 AM
16vV does it again! Thank you.
Jump to: