KanoPool kano.is lowest 0.9% fee 🐈 since 2014 - Worldwide - 2432 blocks - page 789.

mousehouse

full member

Activity: 150

Merit: 100

Quote from: aessedai on October 14, 2017, 10:21:59 AM

Quote from: Philopolymath on October 14, 2017, 09:54:07 AM

Thats better but we are still far behind expected..come on lady luck

Yeah, I've been on this pool for two weeks now and have made roughly half of what I am used to from other pools. I am not sure if 2 weeks is enough for a valid comparison, but I am not just a few percentage points off. I am 50% off. It's feeling rough.

We're at 17 out of 22.5 expected blocks. That's 33%... should even out when we have a better run at some point in time. Variance is a b****.

aessedai

newbie

Activity: 57

Merit: 0

Quote from: Philopolymath on October 14, 2017, 09:54:07 AM

Thats better but we are still far behind expected..come on lady luck

Yeah, I've been on this pool for two weeks now and have made roughly half of what I am used to from other pools. I am not sure if 2 weeks is enough for a valid comparison, but I am not just a few percentage points off. I am 50% off. It's feeling rough.

mdude77

legendary

Activity: 1540

Merit: 1001

Quote from: mousehouse on October 14, 2017, 09:51:53 AM

15+ block, second one today Grin

Nice big fat one by canaan.3333! Woot!

M

Philopolymath

sr. member

Activity: 558

Merit: 295

Walter Russell's Cosmogony is RIGHT!

Thats better but we are still far behind expected..come on lady luck

mousehouse

full member

Activity: 150

Merit: 100

15+ block, second one today Grin

mawk01

full member

Activity: 128

Merit: 100

Quote from: NotFuzzyWarm on October 14, 2017, 09:38:52 AM

Quote from: mawk01 on October 13, 2017, 09:16:11 PM

Alright friends...new problem for me....went out to shut down my 6 741s as I was going to move them around to get ready for a couple L3's coming in. When I turned powered them back on, one of them went through the normal power up cycle, looking at the white lite, turns yellow, then instead turning blue ..I got a red light. On the sides where you normally get the 4 green lights (two on each side), I only got 2 green on the right side, the left side was not lit up at all. So .... did I lose the boards on that side...?? I power cycled several times, and still no change....I've had these about a month now..... Undecided

Highly suggest ya move this query to the Avalon 7 thread in hardware. Canaan monitors it and more to the point - the thread is dedicated to these....

Will do...thanks..

NotFuzzyWarm

legendary

Activity: 3822

Merit: 2703

Evil beware: We have waffles!

Quote from: mawk01 on October 13, 2017, 09:16:11 PM

Alright friends...new problem for me....went out to shut down my 6 741s as I was going to move them around to get ready for a couple L3's coming in. When I turned powered them back on, one of them went through the normal power up cycle, looking at the white lite, turns yellow, then instead turning blue ..I got a red light. On the sides where you normally get the 4 green lights (two on each side), I only got 2 green on the right side, the left side was not lit up at all. So .... did I lose the boards on that side...?? I power cycled several times, and still no change....I've had these about a month now..... Undecided

Highly suggest ya move this query to the Avalon 7 thread in hardware. Canaan monitors it and more to the point - the thread is dedicated to these....

mawk01

full member

Activity: 128

Merit: 100

Quote from: mdude77 on October 14, 2017, 09:31:14 AM

Quote from: mawk01 on October 14, 2017, 09:09:31 AM

Quote from: geobull on October 14, 2017, 03:12:37 AM

Quote from: mawk01 on October 13, 2017, 09:34:51 PM

Quote from: kano on October 13, 2017, 09:27:53 PM

Quote from: mawk01 on October 13, 2017, 09:16:11 PM

Alright friends...new problem for me....went out to shut down my 6 741s as I was going to move them around to get ready for a couple L3's coming in. When I turned powered them back on, one of them went through the normal power up cycle, looking at the white lite, turns yellow, then instead turning blue ..I got a red light. On the sides where you normally get the 4 green lights (two on each side), I only got 2 green on the right side, the left side was not lit up at all. So .... did I lose the boards on that side...?? I power cycled several times, and still no change....I've had these about a month now..... Undecided

Check the PCIe connectors - that's usually the problem - not enough getting through due to a connection problem.
The connections on the boards, where you plug them in, can get a bit touchy if you move them around or unplug/plug them back in.

Thanks Kano....actually I never touched this particular unit, so not sure why....I coulda sworn I kinda heard a pop, and when I looked at the back is when I noticed the red light.... Huh

Got same issue with my one Avalon Unit as you described red light inside have you came up solution ?

Haven't tried that as that particular PSU (parellel 2400) is still powering another Unit just fine.....

no....still have red light at the top....2 green lights on the right side....nothing on the left side of the unit.....

If you plug it into a different PSU, does it do the same thing?

If so, sounds like it might be time to find out how good their warranty service is.

M

mdude77

legendary

Activity: 1540

Merit: 1001

Quote from: mawk01 on October 14, 2017, 09:09:31 AM

Quote from: geobull on October 14, 2017, 03:12:37 AM

Quote from: mawk01 on October 13, 2017, 09:34:51 PM

Quote from: kano on October 13, 2017, 09:27:53 PM

Quote from: mawk01 on October 13, 2017, 09:16:11 PM

Alright friends...new problem for me....went out to shut down my 6 741s as I was going to move them around to get ready for a couple L3's coming in. When I turned powered them back on, one of them went through the normal power up cycle, looking at the white lite, turns yellow, then instead turning blue ..I got a red light. On the sides where you normally get the 4 green lights (two on each side), I only got 2 green on the right side, the left side was not lit up at all. So .... did I lose the boards on that side...?? I power cycled several times, and still no change....I've had these about a month now..... Undecided

Check the PCIe connectors - that's usually the problem - not enough getting through due to a connection problem.
The connections on the boards, where you plug them in, can get a bit touchy if you move them around or unplug/plug them back in.

Thanks Kano....actually I never touched this particular unit, so not sure why....I coulda sworn I kinda heard a pop, and when I looked at the back is when I noticed the red light.... Huh

Got same issue with my one Avalon Unit as you described red light inside have you came up solution ?

no....still have red light at the top....2 green lights on the right side....nothing on the left side of the unit.....

If you plug it into a different PSU, does it do the same thing?

If so, sounds like it might be time to find out how good their warranty service is.

M

mawk01

full member

Activity: 128

Merit: 100

Quote from: geobull on October 14, 2017, 03:12:37 AM

Quote from: mawk01 on October 13, 2017, 09:34:51 PM

Quote from: kano on October 13, 2017, 09:27:53 PM

Quote from: mawk01 on October 13, 2017, 09:16:11 PM

Alright friends...new problem for me....went out to shut down my 6 741s as I was going to move them around to get ready for a couple L3's coming in. When I turned powered them back on, one of them went through the normal power up cycle, looking at the white lite, turns yellow, then instead turning blue ..I got a red light. On the sides where you normally get the 4 green lights (two on each side), I only got 2 green on the right side, the left side was not lit up at all. So .... did I lose the boards on that side...?? I power cycled several times, and still no change....I've had these about a month now..... Undecided

Check the PCIe connectors - that's usually the problem - not enough getting through due to a connection problem.
The connections on the boards, where you plug them in, can get a bit touchy if you move them around or unplug/plug them back in.

Thanks Kano....actually I never touched this particular unit, so not sure why....I coulda sworn I kinda heard a pop, and when I looked at the back is when I noticed the red light.... Huh

Got same issue with my one Avalon Unit as you described red light inside have you came up solution ?

no....still have red light at the top....2 green lights on the right side....nothing on the left side of the unit.....

Biffa

legendary

Activity: 3234

Merit: 1221

Sweet!

kano

legendary

Activity: 4634

Merit: 1851

Linux since 1997 RedHat 4

Block! by cobramining

only 13.2 BTC but not bad for an 11 second network block

geobull

full member

Activity: 168

Merit: 100

Quote from: mawk01 on October 13, 2017, 09:34:51 PM

Quote from: kano on October 13, 2017, 09:27:53 PM

Quote from: mawk01 on October 13, 2017, 09:16:11 PM

Alright friends...new problem for me....went out to shut down my 6 741s as I was going to move them around to get ready for a couple L3's coming in. When I turned powered them back on, one of them went through the normal power up cycle, looking at the white lite, turns yellow, then instead turning blue ..I got a red light. On the sides where you normally get the 4 green lights (two on each side), I only got 2 green on the right side, the left side was not lit up at all. So .... did I lose the boards on that side...?? I power cycled several times, and still no change....I've had these about a month now..... Undecided

Check the PCIe connectors - that's usually the problem - not enough getting through due to a connection problem.
The connections on the boards, where you plug them in, can get a bit touchy if you move them around or unplug/plug them back in.

Thanks Kano....actually I never touched this particular unit, so not sure why....I coulda sworn I kinda heard a pop, and when I looked at the back is when I noticed the red light.... Huh

Got same issue with my one Avalon Unit as you described red light inside have you came up solution ?

mawk01

full member

Activity: 128

Merit: 100

Quote from: kano on October 13, 2017, 09:48:23 PM

Quote from: mawk01 on October 13, 2017, 09:34:51 PM

Quote from: kano on October 13, 2017, 09:27:53 PM

Quote from: mawk01 on October 13, 2017, 09:16:11 PM

Alright friends...new problem for me....went out to shut down my 6 741s as I was going to move them around to get ready for a couple L3's coming in. When I turned powered them back on, one of them went through the normal power up cycle, looking at the white lite, turns yellow, then instead turning blue ..I got a red light. On the sides where you normally get the 4 green lights (two on each side), I only got 2 green on the right side, the left side was not lit up at all. So .... did I lose the boards on that side...?? I power cycled several times, and still no change....I've had these about a month now..... Undecided

Check the PCIe connectors - that's usually the problem - not enough getting through due to a connection problem.
The connections on the boards, where you plug them in, can get a bit touchy if you move them around or unplug/plug them back in.

Thanks Kano....actually I never touched this particular unit, so not sure why....I coulda sworn I kinda heard a pop, and when I looked at the back is when I noticed the red light.... Huh

Well a 'pop' can depend on the PSUs you use.
Some types of PSUs can take 15-30 minutes to reset after a power surge pops their internal 'fuse'
2 silly expensive seasonic 1200 platinums I used to have used to take forever to reset ... until I finally blew them up Tongue

I've had 2 OCZ 1250s since I first started GPU mining on Bitcoin in 2011 ... those 2 still work fine running the A741 ... if only OCZ was still around.

Thanks Kano....Hope that's what it is....I'm using the 2400 watt Parellel PSU's, and the other unit that I have on the other side of it is working fine.....I'm going to leave it disconnected tonite until morning, and keep my fingers crossed. If it doens't resolve itself...any other guess's.....

kano

legendary

Activity: 4634

Merit: 1851

Linux since 1997 RedHat 4

Quote from: mawk01 on October 13, 2017, 09:34:51 PM

Quote from: kano on October 13, 2017, 09:27:53 PM

Quote from: mawk01 on October 13, 2017, 09:16:11 PM

Alright friends...new problem for me....went out to shut down my 6 741s as I was going to move them around to get ready for a couple L3's coming in. When I turned powered them back on, one of them went through the normal power up cycle, looking at the white lite, turns yellow, then instead turning blue ..I got a red light. On the sides where you normally get the 4 green lights (two on each side), I only got 2 green on the right side, the left side was not lit up at all. So .... did I lose the boards on that side...?? I power cycled several times, and still no change....I've had these about a month now..... Undecided

Check the PCIe connectors - that's usually the problem - not enough getting through due to a connection problem.
The connections on the boards, where you plug them in, can get a bit touchy if you move them around or unplug/plug them back in.

Thanks Kano....actually I never touched this particular unit, so not sure why....I coulda sworn I kinda heard a pop, and when I looked at the back is when I noticed the red light.... Huh

Well a 'pop' can depend on the PSUs you use.
Some types of PSUs can take 15-30 minutes to reset after a power surge pops their internal 'fuse'
2 silly expensive seasonic 1200 platinums I used to have used to take forever to reset ... until I finally blew them up Tongue

I've had 2 OCZ 1250s since I first started GPU mining on Bitcoin in 2011 ... those 2 still work fine running the A741 ... if only OCZ was still around.

mawk01

full member

Activity: 128

Merit: 100

Quote from: kano on October 13, 2017, 09:27:53 PM

Quote from: mawk01 on October 13, 2017, 09:16:11 PM

Alright friends...new problem for me....went out to shut down my 6 741s as I was going to move them around to get ready for a couple L3's coming in. When I turned powered them back on, one of them went through the normal power up cycle, looking at the white lite, turns yellow, then instead turning blue ..I got a red light. On the sides where you normally get the 4 green lights (two on each side), I only got 2 green on the right side, the left side was not lit up at all. So .... did I lose the boards on that side...?? I power cycled several times, and still no change....I've had these about a month now..... Undecided

Check the PCIe connectors - that's usually the problem - not enough getting through due to a connection problem.
The connections on the boards, where you plug them in, can get a bit touchy if you move them around or unplug/plug them back in.

Thanks Kano....actually I never touched this particular unit, so not sure why....I coulda sworn I kinda heard a pop, and when I looked at the back is when I noticed the red light.... Huh

kano

legendary

Activity: 4634

Merit: 1851

Linux since 1997 RedHat 4

Quote from: mawk01 on October 13, 2017, 09:16:11 PM

Alright friends...new problem for me....went out to shut down my 6 741s as I was going to move them around to get ready for a couple L3's coming in. When I turned powered them back on, one of them went through the normal power up cycle, looking at the white lite, turns yellow, then instead turning blue ..I got a red light. On the sides where you normally get the 4 green lights (two on each side), I only got 2 green on the right side, the left side was not lit up at all. So .... did I lose the boards on that side...?? I power cycled several times, and still no change....I've had these about a month now..... Undecided

Check the PCIe connectors - that's usually the problem - not enough getting through due to a connection problem.
The connections on the boards, where you plug them in, can get a bit touchy if you move them around or unplug/plug them back in.

overcon

sr. member

Activity: 393

Merit: 250

911 IT Admin. I keep 911 up so you get help ASAP!

It's block time! Let's have a Friday Block Party!

mawk01

full member

Activity: 128

Merit: 100

Alright friends...new problem for me....went out to shut down my 6 741s as I was going to move them around to get ready for a couple L3's coming in. When I turned powered them back on, one of them went through the normal power up cycle, looking at the white lite, turns yellow, then instead turning blue ..I got a red light. On the sides where you normally get the 4 green lights (two on each side), I only got 2 green on the right side, the left side was not lit up at all. So .... did I lose the boards on that side...?? I power cycled several times, and still no change....I've had these about a month now..... Undecided

kano

legendary

Activity: 4634

Merit: 1851

Linux since 1997 RedHat 4

Quote from: mdude77 on October 13, 2017, 06:56:57 PM

Quote from: kano on October 13, 2017, 05:58:33 PM

The thead title

DE, SG, JP, NL, NYA.
Each as e.g. nya.kano.is (instead of stratum.kano.is)

Maybe it'd be useful to spell this out on the website? I can only guess what most of these are. I went by ping, and stratum.kano.is is lowest by far. I'm guessing it's west coast USA somewhere?

M

Not until I complete the last step of the rewrite of the KanoDB code to handle the network - which is still a ways off.
The ckpool node code sux and always has, so I have always preferred to not advertise that on the web site or anywhere else Tongue

Topic: KanoPool kano.is lowest 0.9% fee 🐈 since 2014 - Worldwide - 2432 blocks - page 789. (Read 5352322 times)