Topic: Launching the Antminer L3+, World's Most Powerful and Efficient Litecoin Miner - page 127. (Read 284884 times)

Hi guys.. This is my first post here and as every1 else, i am posting because i have a huge problem.. I got my L3+ on Thursday and i noticed right away that one board was reporting 67 ASICs instead of 72 but the hashing rate was indeed 504 MH/s.. So i left it like that and got to bed.. On Friday that same board was full of xxxxxx, so what i did is i read this exact topic and did a pool switch.. Aftertahat i rebooted the device and everything was fine.. (67 ASICS) reported still.. On Friday afternoon my problems started.. Hashing board just disapeared from my Web Interface.. After that one (with 67 ASICS) second one disapeared, than the third and finaly the last one.. So now, non of the 4 hashing boards are not detected..

I am using original PSU from Bitmain, and i did check all the cables.. They look normal to me. I have also reflashd the device with the firmware from their web site (altho it is the same FW as before) but this did not help..

What i have noticed before, is that on the InfoPage there was a MSG saying something like: Socket Connect failed - Connection refused (for hardware version)

Do u have any idea what could be the problem?

I actuall used the miner for 8 hours.. Thats pretty much it..

PS: I did not overclock the miner if this is important!?


Thank you in advance guys..

Thanks for the response.  Also thank you GMPoison for responding about surge protectors earlier as well.  This place seems very helpful.

do you think it would be a wise time to move over to Pro Hashing now then?

sent a question to nicehash about the drop in earnings and got the following reply from them:

Hashrate on LTC is rising rapidly, seems batches are being delivered and started up.

Current network hash rate has already jumped to more than 18000GH/s, difficultly set to increase >10% in 3 hours or so... Still a good deal but interesting to see the effect of these L3+ batches!

I have the problems from 4 days, But I was getting Hashes proper, My Hashes not fall.

But There is a problem.

1.) When my electricity goes, And when electricity come, then sometime My L3+ 1st Board Temperatures become 0 (zero), And All other Hashing Board temperatues was wrong. There are No Hashing of that 1st board only gives 3 Hashing Board Hashes.

Screenshot:



2) After Restart 1 to 3,4 Times Everything Become normal, All Board was ok. All Hashing Board gives Proper Hashing, No wrong Temperatures, All fine. But After 10 Minutes i see "x" on ASIC Status of 1st board, And there is No fall of Hashes.I was Getting Proper Hashes. But I worried bout that, what is the problem, Why i see single "x" on 1st hashing board. All are saying 1st Hashing board one Chip is damage. But i was getting Hashing Proper, With no Issue.

Screenshot:



Kernel Log-> I was getting also Failed to scale voltage up: -22


[    3.187367] cpu0 supply cpu0 not found, using dummy regulator
[    3.193881] cpufreq_cpu0: failed to scale voltage up: -22
[    3.199706] cpufreq_cpu0: failed to scale voltage up: -22
[    3.212475] ALSA device list:
[    3.215710]   No soundcards found.
[    3.220262] Freeing init memory: 264K
[    3.224315] Failed to execute /init
[    4.220510] jffs2: notice: (122) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[    5.548645] net eth0: initializing cpsw version 1.12 (0)
[    5.557600] net eth0: phy found : id is : 0x7c0f1
[    5.562999] libphy: PHY 4a101000.mdio:01 not found
[    5.568194] net eth0: phy 4a101000.mdio:01 not found on slave 1
[    8.633987] libphy: 4a101000.mdio:00 - Link is Up - 100/Full


Also I had Contact to the, Bitmain Support they Replyed me, Only one chip is damage, But dont worry You are getting Full hash rate. If hashes Fall, Write to us.

I was very worried about it. If i want to Buy Hashing Board from Bitmain will sell It or not. Because In sending Hashing Board From India to China It was very costly.

 

What you think Guys, What will be the problem, In Miner, or In PSU.

Any small Help it will be Big Help for me.

 

Thanks.

The one currently for sale on Bitmain says it has "9 pairs of 6 pin PCI-E connectors" and can power two L3+ when using 220v. I'm assuming 9 pairs means 18 total, since the one that is out of stock and comes with 5 pairs of 6 pin PCI-E connectors says it can only power one L3+? This makes more sense now, I thought 9 pairs meant 9 connectors total, not 16

https://shop.bitmain.com/productDetail.htm?pid=00020170824135847210k2qYaX1L0694

https://shop.bitmain.com/productDetail.htm?pid=000201706220552393488UOm1xDH0679

Yeah, it's a normal P4400 and it "just works". I didn't even realize it wasn't rated for 220v until someone else mentioned that on the YouTube comments  . Seems to work well though. I would expect the PSU to handle small surges, but large surges are definitely a risk. On a related note, these miners seem to handle brown-outs quite well.

It's a little confusing, but there are two versions of the APW3++. One of them has 5 pairs of connectors (10 total) and the other has 9 pairs of connectors (18 total). I believe you're looking at the one that has 9 pairs, which can run two L3+ from a single PSU when using 220v.

Well apparently from the reviews of the APW3++ and the L3+, it only consumes 750w on 220 volt, which would make sense because Bitmain literally advertises that you can safely run two L3+'s off one since it supplies 1600w at 220v. Plus, you should be able to underclock the L3+ so it consumes slightly less power, no?

The last batch ...they gave 2 hour notice ...and according to others on this thread (looking at html) moved 10,000 units in 40 min

they really don't care anymore...and also the web site worked better when 1/2 the world was asleep and trying not to sign on

so to bitmain it is a win/win ..they sell out in 40 min vs 20 min and the www site does not crash completely and they save

big bucks not upgrading it

so be up at around 3am every nite or so to look at twitter ...that is about how much notice you may have 2 hours in the middle of the nite (in usa anyway)

me I work nites (na/na/na bitmain) and caught it in time





Below is for the bitmain L3+++ PSU

I'd only run ONE unit per bitmain product anyway...2 units is tough imho and hell for 125 bucks why risk it....anyway that is what I"m doing with my L3's since april etc..with
no issues

I think the max on them is around 1600 watts so I think 2 units at 800 watts for an L3+ pushes it just a bit much

me ...not worth the risk for 125 bucks more just to get one per my units

my 2 satoshi's worth

brad

That's pretty funny. I'm not taking that bait. Not envious I can assure you. I don't have a soft flagging ego either so I won't be regaling the forum with any reasons why. I'll just let you pretend "masters of the universe" get back to your little circle jerk. It's moderately amusing.

In the description of the APW3++ it says it only comes with 9 connectors, but in your video it clearly comes with 10. If it only came with 9, it wouldn't be able to power up two, so I guess it's a typo on their website?

Will stick to this, thanks for the info 

Bitmain usually gives a little heads up by posting in their Twitter account. https://twitter.com/bitmaintech

Anyone know when we will be able to place orders for the next batch ?

Assuming I'm at the right place : https://shop.bitmain.com/productDetail.htm?pid=000201708241118172509G4Uv52o0647

Seems like they don't talk about the next releasing date, I've been roaming on their website for quite a few days now.

Any satisfied buyers or helpful volunteer to give some information about release date or any other place to get some L3+ ?

Cheers, thanks

I ordered a few L3+ couple of days ago. I'm not going thru with the orders now. Please message me if you're interested in taking them away from me.

I don't know much about the kill a watt, but as far as surge protectors go, I believe they're available in high wattage and voltage but they are very costly. Don't quote me on it, but I believe most breakers these days have surge protectors built in, and most power supplies these days are designed to be able to handle surges without damaging the equipment they're hooked up to.

Yes, but I was curious about the kill a watt meter itself.  I guess I was vague with my pronouns, sorry.  To clarify, the p4400 kill a watt's max operating voltage at p3's website says 125v, and it kind of looks like the one in that video I quoted was the p4400, so I wanted to check with cryptocrane about it.  Or anyone else who uses kill a watts at 240v.

You need a minimum of 110V with the PSU from Bitmain. But it also runs on 220 and 240V  I have not heard of any PSU running on a higher circuit. On the other hand 240V is probably the highest i have seen in my life anyway (for normal goods and not industry heavy machines)