Greetings fullzero. I'm working on similar thing, but with textmode and netboot and I'm in the begining of the road (did an image with this guide and cannot log in to it, 'cause no users were exported)). Please tell
1. What where your base pendrive livecd image and modifying soft?
2. Why separate builds for different mobos?
Topic: [ mining os ] nvoc - page 351. (Read 418557 times)
Which program you are printing the image file to.
Bios above memory 4g is enable when the system is not open from the USB freeze...
Bios above memory 4g is enable when the system is not open from the USB freeze...
Also with this mobo I have found (with Nvidia cards) you can use ribbon risers for all but the second (16x primary gpu slot). It must have a powered riser to ensure proper operation.
Are you saying that only x16 slot must have powered riser on Anniversary Asrock?
So x1 slots are providing more than 25W (as per PCIe specification) on that mobo?
Usually only x16 slots can be used without powered risers, as I understand.
Or I do not understand?
Have you tried disabling and then enabling the ethernet?
Yeah I tried this and a few others things, but to no avail. I only have one of these 990fxa-ud3 so it's no big deal to use wifi.
I keep sayng I'm going to troubleshoot when the rig needs a reboot, but I've yet to need one; nvOC has truely been set it and forget it thusfar.
@fullzero I see you listed compatible mobo's in the OP. The board in the rig I am about to put new GPU's in is an ASRock Anniversary. Any ideas if that will be compatible with this image? Also will the image fit on an 8gb usb drive? Thanks.
musicoin pool I am using here http://213.154.202.174:3330/ This is mostly used http://nomnom.technology/#/
zclassic We are not digging yet zclassic for https://suprnova.cc/ available.
zclassic We are not digging yet zclassic for https://suprnova.cc/ available.
here is a new oneBash with MUSIC and ZCL
I used MC POOL http://213.154.202.174:3330/ for the default MUSIC pool, as you said this is what you use.
I used zcl.coinmine.pl https://www2.coinmine.pl/zcl/index.php for the default ZCL pool, as it has good reviews.
Thank you...
musicoin pool I am using here http://213.154.202.174:3330/ This is mostly used http://nomnom.technology/#/
zclassic We are not digging yet zclassic for https://suprnova.cc/ available.
zclassic We are not digging yet zclassic for https://suprnova.cc/ available.
How can i add musicoin and ZClassic.
How can I add any coin...
How can I add any coin...
Thanks, further questions incoming, no doubt.
I feel somewhat bad that you took the trouble to answer in such lengthy fashion.
I did not formulate my question in the right way.
The fact is I do not want to use onebash functionality.
I want to use nvOC because its fully stocked with all that is needed to start mining.
I want to overclock and set power limits myself in the OS itself.
So, the question is, how do I bypass Onebash and do stuff the oldfashioned way?
I did not formulate my question in the right way.
The fact is I do not want to use onebash functionality.
I want to use nvOC because its fully stocked with all that is needed to start mining.
I want to overclock and set power limits myself in the OS itself.
So, the question is, how do I bypass Onebash and do stuff the oldfashioned way?
Can i use your OS for mixed GPU rig - RX480 and 1080ti ?
I would like to run both on Claymore ETH miner.
Thanks
I would like to run both on Claymore ETH miner.
Thanks
You would have to install the AMDGPU-PRO driver first. I haven't tried a mixed Nvidia / AMD on linux.
If you want to test it out yourself; download the Ubuntu 16.04 version here:
http://support.amd.com/en-us/kb-articles/Pages/AMD-Radeon-GPU-PRO-Linux-Beta-Driver%E2%80%93Release-Notes.aspx
open a standard terminal: press f12
follow AMD instructions for install. I would follow this portion: as you don't need all the Ubuntu updates.
IMO a mixed Nvidia / AMD would never be as stable as a pure rig; but I have seen a lot of members post about mixed rigs.
I will install the AMDGPU-PRO myself and test a mixed Nvidia / AMD rig later; probably won't have time to try this out until next week.
that will be great and appreciate the efforts fullzero
ello guvna,
i have been trying to compile tpruvots ccminer on kubuntu 16.04 to no avail
how did you compile it?
did you use cuda 7.5?
there are dozens of guides and each one is different from the other and results in different errors
also, i would like to give nvOC a test drive
do I need to configure anything in onebash before I boot it?
i have been trying to compile tpruvots ccminer on kubuntu 16.04 to no avail
how did you compile it?
did you use cuda 7.5?
there are dozens of guides and each one is different from the other and results in different errors
also, i would like to give nvOC a test drive
do I need to configure anything in onebash before I boot it?
Can i use your OS for mixed GPU rig - RX480 and 1080ti ?
I would like to run both on Claymore ETH miner.
Thanks
I would like to run both on Claymore ETH miner.
Thanks
Is this os completely sustainable on its own?
Like I mean burn plug and mine?
I don't need to mess with the interface once the USB is setup?
Like I mean burn plug and mine?
I don't need to mess with the interface once the USB is setup?
If you use one of the fully supported motherboards, currently:
ASRock H81 PRO BTC, BIOSTAR TB85, MSI Z270-A PRO (in stock)
then yes; it is essentially:
burn, configure oneBash (or replace the one on the usb with one you have already configured), plug and power on.
If you are using an untested motherboard; most likely all the cards will be recognized and mining will automatically start: however their may be slight differences which cause the xorg file to not properly enable OC on all the cards. This may be hard to notice without directly connecting a monitor and inspecting the mining process. If using an untested motherboard, you probably should connect a monitor and ensure everything is working as intended ~6 minutes after initial boot. If you have a motherboard which doesn't properly enable OC on all the cards; tell me. For any motherboard commonly used, I will get one myself and provide a fully supported image.
Is this os completely sustainable on its own?
Like I mean burn plug and mine?
I don't need to mess with the interface once the USB is setup?
Like I mean burn plug and mine?
I don't need to mess with the interface once the USB is setup?
Very nice setup.
I can see this doing 1080 ti
With a gold Evga 1600 g2
It will be more costly but if you only have room for 1 rig you could push 3840 hash .
My two Msi 1080 ti do 640 and 642 which is 1282
I posted in thread I think you could do the build with 1080 ti. And push 3800 h
This would cost more but if you could only have 1 unit it would be a monster
I can see this doing 1080 ti
With a gold Evga 1600 g2
It will be more costly but if you only have room for 1 rig you could push 3840 hash .
My two Msi 1080 ti do 640 and 642 which is 1282
I posted in thread I think you could do the build with 1080 ti. And push 3800 h
This would cost more but if you could only have 1 unit it would be a monster
What motherboard are you using?
I'm using a Gigabyte 990FXA-UD3 R5.
To get ethernet working on 16.04 server I just had to enable ioummu in the bios, and just set dhcp in /etc/network/interfaces.
Doesn't help 
I think the issue is with the fact I'm running headless over iKVM on a SuperMicro X9DR7-LN4F that is using the Matrox GPU built into the IPMI chipset.
I think the issue is with the fact I'm running headless over iKVM on a SuperMicro X9DR7-LN4F that is using the Matrox GPU built into the IPMI chipset.
That's probably it.
Might work with a monitor direct to the primary GPU.
What cards are you running on this?
What program or application layer protocol are you using to remote access?
Do you mine XMR or other coin with the cpus?
I'm running a couple of 1080 ti cards, but need it to work without a monitor
Remote access is via the built in IPMI on the Supermicro motherboard
https://www.servethehome.com/supermicro-ipmiview-review-remote-server-monitoring-management-ipmi-20-kvm-over-ip/
I might do some XMR mining as it's a dual E5 Xeon board
The same symptoms occur if I take a vanilla ubuntu install and then load the nvidia drivers.
Login prompt takes the password, but then just reloads to the login again
Doesn't help
I think the issue is with the fact I'm running headless over iKVM on a SuperMicro X9DR7-LN4F that is using the Matrox GPU built into the IPMI chipset.
I think the issue is with the fact I'm running headless over iKVM on a SuperMicro X9DR7-LN4F that is using the Matrox GPU built into the IPMI chipset.
Pretty sure this is something really simple...but I can't get a login to the desktop
I get a prompt with either m1 or Guest session and the password miner1 doesn't work for me at all.
It seems to take it but just jumps back to the login screen again
I get a prompt with either m1 or Guest session and the password miner1 doesn't work for me at all.
It seems to take it but just jumps back to the login screen again
Jump to: