Topic: My RX580 Benchmarking and Results: 30.5Mh/s @ 77.5W (+ 1130MH/s Dcr w/ 125W) - page 4. (Read 189842 times)
February 05, 2018, 04:58:53 AM
i have 580 8gb gigabyte with hynix memory and 1 sapphire with micron memory, in wattman my max memory setting is 2250 (wich i m running on), how can other ppl set memory higher?
February 01, 2018, 02:25:19 PM
Hey, new miner also. Mining for 3 weeks allready have 11 sapphire nitro special edition 8gb. Stable 30.2 MH without modding bios. Dont have power meter, but seems my cards taken lot of electricify on globalpowertune 5. Trying to set 3. Stable for few hours now. How much mh i can reach if i flash bios? I'm useing core 1250, mem 2290 on ethos
February 01, 2018, 12:27:22 PM
Thanks to everyone who has contributed to this thread!
I'm looking for help in getting my 2 XFX RX 580 GB Hynix to hashing > 30 Mhs. I'm close and getting a consistent 29-29.5, but never go above 29.5. I've made the following changes:
GlobalCore 1200
GlobalMem 2175
GlobalPowerTune 3
Globalminer Claymore (9.7)
Modded the GPU Rom to copy the 1750 Mhz Timing setting to the 2000 Mhz setting.
I've seen several instances of people getting over 30 Mhs with this card. How can I get that last 1 Mhs?
My numbers are based on single mining ETH.
TIA.
mu2pilot
I'm looking for help in getting my 2 XFX RX 580 GB Hynix to hashing > 30 Mhs. I'm close and getting a consistent 29-29.5, but never go above 29.5. I've made the following changes:
GlobalCore 1200
GlobalMem 2175
GlobalPowerTune 3
Globalminer Claymore (9.7)
Modded the GPU Rom to copy the 1750 Mhz Timing setting to the 2000 Mhz setting.
I've seen several instances of people getting over 30 Mhs with this card. How can I get that last 1 Mhs?
My numbers are based on single mining ETH.
TIA.
mu2pilot
Hi, sorry for quoting after long time, but I need some help. I will have in couple of days 3xXFX RX 580 GTS XXX 8gb, so I am wondering what PSU are you using, i have one of 1000 watts, but not sure if this gonna be enough.
Hope you will answer.....
Thanks in advance.
January 31, 2018, 07:38:26 PM
HWInfo is very nasty tool. I did notice, it is able to cause issues to miners when restarted (to be more specific, if you restart miner while running HWInfo). Incorrect voltage, wrong clocks, memory erros or slow hashrate - only OS reboot fixes the problem. Also be sure You use only one tool at time to control clocks/voltages, for example if You use Claymore to control voltages, uninstal Afterburner because they can interfere each other.
Hi,
I doned all you recommend but the problem persist, perhaps how can i check if correct voltage is being aplicated in my core?
I use cast_xmr-vega to mine.
Reagrds
You can use gpuz
Hi,
Thanks for help people
I use this tool too. But the voltage that i choose in P7 stage in Overdrivetool is applied but only 1 or 2 minutes. After that an other voltage is automatically selected. Could be a bug in blockchaindrivers?
I tried to lock all P2 - P7 stages but the voltage only works momenteneos and if i change the clock too.. Very strange.. Maybe im doing something wrong...
My config:
https://imgur.com/a/zUZhF
Regards
Check this: https://mining.help/ 9. Overclock/Undervolt
January 31, 2018, 03:40:34 PM
HWInfo is very nasty tool. I did notice, it is able to cause issues to miners when restarted (to be more specific, if you restart miner while running HWInfo). Incorrect voltage, wrong clocks, memory erros or slow hashrate - only OS reboot fixes the problem. Also be sure You use only one tool at time to control clocks/voltages, for example if You use Claymore to control voltages, uninstal Afterburner because they can interfere each other.
Hi,
I doned all you recommend but the problem persist, perhaps how can i check if correct voltage is being aplicated in my core?
I use cast_xmr-vega to mine.
Reagrds
You can use gpuz
Hi,
Thanks for help people
I use this tool too. But the voltage that i choose in P7 stage in Overdrivetool is applied but only 1 or 2 minutes. After that an other voltage is automatically selected. Could be a bug in blockchaindrivers?
I tried to lock all P2 - P7 stages but the voltage only works momenteneos and if i change the clock too.. Very strange.. Maybe im doing something wrong...
My config:
https://imgur.com/a/zUZhF
Regards
January 31, 2018, 09:10:11 AM
Hello, I have not found hash information or bios of the sapphire rx570 pulse 8gb, 4gb if there is information. Some help?
January 31, 2018, 01:38:13 AM
HWInfo is very nasty tool. I did notice, it is able to cause issues to miners when restarted (to be more specific, if you restart miner while running HWInfo). Incorrect voltage, wrong clocks, memory erros or slow hashrate - only OS reboot fixes the problem. Also be sure You use only one tool at time to control clocks/voltages, for example if You use Claymore to control voltages, uninstal Afterburner because they can interfere each other.
Hi,
I doned all you recommend but the problem persist, perhaps how can i check if correct voltage is being aplicated in my core?
I use cast_xmr-vega to mine.
Reagrds
You can use gpuz
January 30, 2018, 04:37:05 PM
HWInfo is very nasty tool. I did notice, it is able to cause issues to miners when restarted (to be more specific, if you restart miner while running HWInfo). Incorrect voltage, wrong clocks, memory erros or slow hashrate - only OS reboot fixes the problem. Also be sure You use only one tool at time to control clocks/voltages, for example if You use Claymore to control voltages, uninstal Afterburner because they can interfere each other.
Hi,
I doned all you recommend but the problem persist, perhaps how can i check if correct voltage is being aplicated in my core?
I use cast_xmr-vega to mine.
Reagrds
January 30, 2018, 01:39:27 PM
HWInfo is very nasty tool. I did notice, it is able to cause issues to miners when restarted (to be more specific, if you restart miner while running HWInfo). Incorrect voltage, wrong clocks, memory erros or slow hashrate - only OS reboot fixes the problem. Also be sure You use only one tool at time to control clocks/voltages, for example if You use Claymore to control voltages, uninstal Afterburner because they can interfere each other.
January 30, 2018, 10:21:33 AM
I got the same problem.
If i change using Msiafterburner or even OverdriveNtoll, i can efectevely change the core clock voltage.
If i see HWINFO64 i see my core goes to 0.94v but after a while he returns to 1.063 for example..
Anyideia what should i look?
I got an
Asrock H110 PRO BTC
120gb SSD
8GB Ram
CPU G4400
1 Saphire 8gb NItro + 7 Shaphire 4gb Nitro
2 EVGA 750 watts GQ
Windows 10
Thanks
If i change using Msiafterburner or even OverdriveNtoll, i can efectevely change the core clock voltage.
If i see HWINFO64 i see my core goes to 0.94v but after a while he returns to 1.063 for example..
Anyideia what should i look?
I got an
Asrock H110 PRO BTC
120gb SSD
8GB Ram
CPU G4400
1 Saphire 8gb NItro + 7 Shaphire 4gb Nitro
2 EVGA 750 watts GQ
Windows 10
Thanks
January 30, 2018, 02:56:13 AM
did you try with fixed numbers from bios mod?
I tried, but it does not work too.
January 29, 2018, 04:43:31 PM
did you try with fixed numbers from bios mod?
January 29, 2018, 02:08:37 PM
Oh man - did You even bother to read what I just wrote? If I set -cvddc 880 -mvddc 950, Vcore would be 950 anyway. It is somehow "linked". cvddc can not be lower than mvddc. If You do not believe me, check it by yourself. Lot of ppl thinks that their GPUS works on very low voltage, becasue they didn't bother to check it. It also does not matter if U use voltage control @: claymore, trixxxx, afterburner, wattool etc. 
January 29, 2018, 11:39:40 AM
Guys, is there any way to separate memory controller and gpu voltage? I would like to set for example GPU core voltage @880 [mV] and Memory Contorler Voltage @950 [mV]. But no matter what I try, it is always like the lowest GPU voltage I can achieve is the Voltage set by Memory Controller. In this example GPU@880 and Memory@950 result in both @950 mV. Is there any way to fix this in PBE, or it is impossible or require more difficult BIOS mod?
Simplest way is with Claymore miner, just use the options -cvddc 880 -mvddc 950
January 29, 2018, 09:18:53 AM
Guys, is there any way to separate memory controller and gpu voltage? I would like to set for example GPU core voltage @880 [mV] and Memory Contorler Voltage @950 [mV]. But no matter what I try, it is always like the lowest GPU voltage I can achieve is the Voltage set by Memory Controller. In this example GPU@880 and Memory@950 result in both @950 mV. Is there any way to fix this in PBE, or it is impossible or require more difficult BIOS mod?
January 25, 2018, 09:50:25 AM
Hello, guys.
I'm having issues with my 6 RX 580 Nitro+. The problem is the last few days I started getting "GPU hangs in OpenCL call" error. I did lower the clocks and I wasn't getting errors in HWiNFO64, but the "GPU hangs in OpenCL call" error still occured today, even without getting GPU errors.
Do you guys have any idea what else can cause the issue?
I've got that too, but it seems intermittend. Sometimes it goes for days without it and sometimes i've got it a couple of times a day. A reboot fixes it, also without any errors. It has been sugested that it can be triggerd by using a VNC server to access your Windows host, but I can't confirm that myself.I'm having issues with my 6 RX 580 Nitro+. The problem is the last few days I started getting "GPU hangs in OpenCL call" error. I did lower the clocks and I wasn't getting errors in HWiNFO64, but the "GPU hangs in OpenCL call" error still occured today, even without getting GPU errors.
Do you guys have any idea what else can cause the issue?
Edit: I got the "GPU hangs in OpenCL call" last night. Can somebody please advise me what should I do in this situation?
Start with default memory clocks first then add 25 when stable until you crash again. Dial back down then that’s your sweet spot. You should do this to all cards individually as no card has the same ASIC quality.
January 24, 2018, 02:56:36 AM
Hello, guys.
I'm having issues with my 6 RX 580 Nitro+. The problem is the last few days I started getting "GPU hangs in OpenCL call" error. I did lower the clocks and I wasn't getting errors in HWiNFO64, but the "GPU hangs in OpenCL call" error still occured today, even without getting GPU errors.
Do you guys have any idea what else can cause the issue?
I've got that too, but it seems intermittend. Sometimes it goes for days without it and sometimes i've got it a couple of times a day. A reboot fixes it, also without any errors. It has been sugested that it can be triggerd by using a VNC server to access your Windows host, but I can't confirm that myself.I'm having issues with my 6 RX 580 Nitro+. The problem is the last few days I started getting "GPU hangs in OpenCL call" error. I did lower the clocks and I wasn't getting errors in HWiNFO64, but the "GPU hangs in OpenCL call" error still occured today, even without getting GPU errors.
Do you guys have any idea what else can cause the issue?
Edit: I got the "GPU hangs in OpenCL call" last night. Can somebody please advise me what should I do in this situation?
January 23, 2018, 03:58:10 PM
yes gurgelkoff.
1150/850mv 2150/850mv
core clock/ voltage for core clock then mem clock /voltage for mem
thats pretty much it.
1150/850mv 2150/850mv
core clock/ voltage for core clock then mem clock /voltage for mem
thats pretty much it.
January 23, 2018, 02:01:36 PM
(...)
pulled over 180mh/s
watts 970
(...)
pulled over 180mh/s
watts 970
(...)
Interesting. Where do you measure these watts? Software or at the wall? I've got 2 rigs mixed with rx480&rx580's and they are so power hungry. Yours seems to draw under 160w/card.
https://image.ibb.co/dcOQgw/IMG_E6253.jpg
this is with all the rig and usb mouse and keyboard
at card, look here from techhpower gpu
https://image.ibb.co/c2DDZG/IMG_6298.jpg
pulling 181mh/s
https://image.ibb.co/jGdrMw/IMG_6299.jpg
yes they are 150-160watts out of the box, but you haven't modded them? when i stated i was 1480 watts at wall , i then got to 1100 or so with small mods
https://image.ibb.co/cV5SuG/RBNB5445.jpg
i have been told on anoak site, i should be around 880watts, with 31mh/s but the guy has not got back to me yet with the bios
WOW! That's how it should look! I bet you are running Windows?
Your figures, how does one read those: "1150/850mv 2150/850mv" First looks like clock speed and the second voltage. Is the first pair coreclock and the second pair memory? Sorry for my noob questions
Do you use PolarisEditor to hack bios or something like Trixx or Afterburner to do it on the fly?
I'm using Linux so I have to set everything up in Windows using Polaris Editor and then move to the Linux rig.
Megahash works OK, I get around 29Mh/s but it seems quite hard to get the watt usage down when the card sits in the linux box. Can't figure out how the same bios can act so differently.
January 23, 2018, 10:06:29 AM
Hello, guys.
I'm having issues with my 6 RX 580 Nitro+. The problem is the last few days I started getting "GPU hangs in OpenCL call" error. I did lower the clocks and I wasn't getting errors in HWiNFO64, but the "GPU hangs in OpenCL call" error still occured today, even without getting GPU errors.
Do you guys have any idea what else can cause the issue?
I've got that too, but it seems intermittend. Sometimes it goes for days without it and sometimes i've got it a couple of times a day. A reboot fixes it, also without any errors. It has been sugested that it can be triggerd by using a VNC server to access your Windows host, but I can't confirm that myself. I'm having issues with my 6 RX 580 Nitro+. The problem is the last few days I started getting "GPU hangs in OpenCL call" error. I did lower the clocks and I wasn't getting errors in HWiNFO64, but the "GPU hangs in OpenCL call" error still occured today, even without getting GPU errors.
Do you guys have any idea what else can cause the issue?
Jump to: