Pages:
Author

Topic: NBMiner v42.2, 100% LHR unlock for ETH mining ! - page 31. (Read 54340 times)

member
Activity: 134
Merit: 26
Volta's tensor cores don't support the INT8 mode supported by Turing's tensor cores, and BTM's tensority algo uses 8-bit matrix multiplication.

That being said, the @NebuTech devs could make a version specifically for Volta's tensor cores which used the FP16 matrix multiply mode supported by Volta, since you can encode INT8 numbers in FP16 format with no loss of precision.

yes, but there are other limitation other than operator type.
member
Activity: 93
Merit: 41
Volta's tensor cores don't support the INT8 mode supported by Turing's tensor cores, and BTM's tensority algo uses 8-bit matrix multiplication.

That being said, the @NebuTech devs could make a version specifically for Volta's tensor cores which used the FP16 matrix multiply mode supported by Volta, since you can encode INT8 numbers in FP16 format with no loss of precision.
member
Activity: 134
Merit: 26
I have a 3 Titan V's and get an error when trying to use any version higher than 13.1

Cuda Error (err_no=209)

any help on a solution

The tensor cores on TTV is different from those on RTXs.

newbie
Activity: 3
Merit: 0
I have a 3 Titan V's and get an error when trying to use any version higher than 13.1

Cuda Error (err_no=209)

any help on a solution
sr. member
Activity: 428
Merit: 250
Inactivity: 8963
Good question, 2070 should be doing half of 2080ti's hashrate, so 7500h/s i guess?
member
Activity: 161
Merit: 10
Anyone tested lower RTX cards like the 2080,2070 and 2060?
sr. member
Activity: 428
Merit: 250
Inactivity: 8963
I currently mine Bytom with 1080ti's. What's the BTM hashrate for 2080ti under v.14?

[...]
On theory, single 2080ti can hit around 17,000 H/s.
It can and it does:



member
Activity: 134
Merit: 26
what is CUTL/MUTL? also add total power to the summary output on line with total speed

Core utilization & memory utilization.

Thanks for the advice, consider add total power display in future versions.
newbie
Activity: 164
Merit: 0
what is CUTL/MUTL? also add total power to the summary output on line with total speed
member
Activity: 134
Merit: 26
^^^Good to see a public miner finally putting to use Turing's tensor cores.
What? You can actually use the tensor cores for mining? Smiley
Is there any chance we will see tensor cores used in other algos?

Yes, v14.0 utilizes tensor cores to tripple the BTM mining hashrate.
sr. member
Activity: 463
Merit: 250
^^^Good to see a public miner finally putting to use Turing's tensor cores.
What? You can actually use the tensor cores for mining? Smiley
Is there any chance we will see tensor cores used in other algos?
jr. member
Activity: 155
Merit: 4
grin 2.6-2.7 for 1060 g6 on windows 1809, i think other miner claim about 3, but don't work on windows 10 72w per car thought, so maybe could get that 3gps if i would OC

member
Activity: 93
Merit: 41
^^^Good to see a public miner finally putting to use Turing's tensor cores.
member
Activity: 134
Merit: 26
I currently mine Bytom with 1080ti's. What's the BTM hashrate for 2080ti under v.14?



BTM: 8 x 2080ti.

Hits temp wall, and not full TDP.

On theory, single 2080ti can hit around 17,000 H/s.
sr. member
Activity: 399
Merit: 254
lots of stale shares
https://ibb.co/Y85FxFH
member
Activity: 134
Merit: 26
@NebuTech devs, mining BTM with a 1060 6gb on AntPool shows around 1600 h/s on the console but only around 1000 h/s on AntPool's side (reject ratio is only around 1%). This is with v13.2, trying v14 now.

Any idea on why the large discrepancy between local/console hashrate and pool side hashrate?

There is several reasons that hashrate on miningpool lower than local console print.

For your specific situation, the reasons maybe:

1. Not enough running time. Run for 24 Hours, check again.
2. High mining difficulty on mining pool & too few cards.
newbie
Activity: 11
Merit: 0
member
Activity: 93
Merit: 41
@NebuTech devs, mining BTM with a 1060 6gb on AntPool shows around 1600 h/s on the console but only around 1000 h/s on AntPool's side (reject ratio is only around 1%). This is with v13.2, trying v14 now.

Any idea on why the large discrepancy between local/console hashrate and pool side hashrate?
newbie
Activity: 10
Merit: 0
I currently mine Bytom with 1080ti's. What's the BTM hashrate for 2080ti under v.14?
Pages:
Jump to: