[Setup & Troubleshoot] Bitmain AntMiner S1 180GH/S miner

Unacceptable

legendary

Activity: 2212

Merit: 1001

Quote from: MarcelliusKBitcoinForum on December 14, 2016, 05:35:08 AM

Quote from: Unacceptable on December 14, 2016, 05:09:45 AM

Quote from: MarcelliusKBitcoinForum on December 14, 2016, 04:56:06 AM

Quote from: QuentinA on December 14, 2016, 04:45:37 AM

Quote from: MarcelliusKBitcoinForum on December 14, 2016, 04:39:28 AM

I bought a used S1, but can't get into the gui. Tried resetting twice in row and waiting 2 minutes inbetween, then taking of power, wait 30 seconds, and then starting it up again. Reset does nothing... Front fan is not working. My green light is flashing, the red is is lit, but the wan leds are not lit.

Probably broken fan, youneed to put another one on, it will boot only with a working fan

I replaced the fan upfront with the working fan. It starts spinning. When I try to ping the IP that's on the antminer, it says destination host unreachable. When I try 192.168.1.99 the same. Then WAN led is still not lit.

If its been reset,the IP may not be in the 192.168.1.99 range,try looking with a laptop or PC in the 192.168.2.99 range.See 1st page of this thread Wink

Changed my computers IP to 192.168.2.254. Tried pinging 192.168.2.99, same message. Can't find the miner.

Hook it up with an ethernet cable to your PC (your PC will not be on any network,unless you got WiFi) & see if you can see it at all,change IP to the 1 & then 2 range.It should at least show up........

MarcelliusKBitcoinForum

newbie

Activity: 4

Merit: 0

Quote from: adaseb on December 14, 2016, 06:20:33 AM

Do you realize that you will only make $0.12/day with this miner. If you pay for power you will most likely make -$1.00

I know, but I am only doing it for fun. Seller told me he would take it back if I can't get it to work.

adaseb

legendary

Activity: 3808

Merit: 1723

Do you realize that you will only make $0.12/day with this miner. If you pay for power you will most likely make -$1.00

MarcelliusKBitcoinForum

newbie

Activity: 4

Merit: 0

Quote from: Unacceptable on December 14, 2016, 05:09:45 AM

Quote from: MarcelliusKBitcoinForum on December 14, 2016, 04:56:06 AM

Quote from: QuentinA on December 14, 2016, 04:45:37 AM

Quote from: MarcelliusKBitcoinForum on December 14, 2016, 04:39:28 AM

I bought a used S1, but can't get into the gui. Tried resetting twice in row and waiting 2 minutes inbetween, then taking of power, wait 30 seconds, and then starting it up again. Reset does nothing... Front fan is not working. My green light is flashing, the red is is lit, but the wan leds are not lit.

Probably broken fan, youneed to put another one on, it will boot only with a working fan

I replaced the fan upfront with the working fan. It starts spinning. When I try to ping the IP that's on the antminer, it says destination host unreachable. When I try 192.168.1.99 the same. Then WAN led is still not lit.

If its been reset,the IP may not be in the 192.168.1.99 range,try looking with a laptop or PC in the 192.168.2.99 range.See 1st page of this thread Wink

Changed my computers IP to 192.168.2.254. Tried pinging 192.168.2.99, same message. Can't find the miner.

Unacceptable

legendary

Activity: 2212

Merit: 1001

Quote from: MarcelliusKBitcoinForum on December 14, 2016, 04:56:06 AM

Quote from: QuentinA on December 14, 2016, 04:45:37 AM

Quote from: MarcelliusKBitcoinForum on December 14, 2016, 04:39:28 AM

I bought a used S1, but can't get into the gui. Tried resetting twice in row and waiting 2 minutes inbetween, then taking of power, wait 30 seconds, and then starting it up again. Reset does nothing... Front fan is not working. My green light is flashing, the red is is lit, but the wan leds are not lit.

Probably broken fan, youneed to put another one on, it will boot only with a working fan

I replaced the fan upfront with the working fan. It starts spinning. When I try to ping the IP that's on the antminer, it says destination host unreachable. When I try 192.168.1.99 the same. Then WAN led is still not lit.

If its been reset,the IP may not be in the 192.168.1.99 range,try looking with a laptop or PC in the 192.168.2.99 range.See 1st page of this thread Wink

MarcelliusKBitcoinForum

newbie

Activity: 4

Merit: 0

Quote from: QuentinA on December 14, 2016, 04:45:37 AM

Quote from: MarcelliusKBitcoinForum on December 14, 2016, 04:39:28 AM

I bought a used S1, but can't get into the gui. Tried resetting twice in row and waiting 2 minutes inbetween, then taking of power, wait 30 seconds, and then starting it up again. Reset does nothing... Front fan is not working. My green light is flashing, the red is is lit, but the wan leds are not lit.

Probably broken fan, youneed to put another one on, it will boot only with a working fan

I replaced the fan upfront with the working fan. It starts spinning. When I try to ping the IP that's on the antminer, it says destination host unreachable. When I try 192.168.1.99 the same. Then WAN led is still not lit.

QuentinA

hero member

Activity: 628

Merit: 504

Quote from: MarcelliusKBitcoinForum on December 14, 2016, 04:39:28 AM

I bought a used S1, but can't get into the gui. Tried resetting twice in row and waiting 2 minutes inbetween, then taking of power, wait 30 seconds, and then starting it up again. Reset does nothing... Front fan is not working. My green light is flashing, the red is is lit, but the wan leds are not lit.

Probably broken fan, youneed to put another one on, it will boot only with a working fan

MarcelliusKBitcoinForum

newbie

Activity: 4

Merit: 0

I bought a used S1, but can't get into the gui. Tried resetting twice in row and waiting 2 minutes inbetween, then taking of power, wait 30 seconds, and then starting it up again. Reset does nothing... Front fan is not working. My green light is flashing, the red is is lit, but the wan leds are not lit.

connectCORRECT

newbie

Activity: 22

Merit: 0

Hi guys,

question, perhaps more for programmers and all who went further in depth sw Antmineru S1. But I was wondering this for Antminery S3-S9.

It would be possible to reduce the maximum temperature set by the manufacturer at 80 degrees C?

In S3 and above this temperature limitation can be switched off only. But I needed it must reduce to 60 - 70 degrees C. In order not to overload.
Then I could turn off the fan and it would be quiet :-)
I have proved that S1 has cooled to 80 degrees C, it automatically goes again.
Then it would work as a thermostat. Yes, the production would be lower. But mostly silence. In the winter, it would be ideal for heating :-)

ErikW79

full member

Activity: 154

Merit: 100

Quote from: aigeezer on July 16, 2016, 01:56:50 PM

Quote from: ErikW79 on July 15, 2016, 05:31:04 PM

I have bought an used S2 miner. Saw it runing and mining, but at home whan I start mining some time after almost all chips show x. And also a beeping noise starts. Any clue what it means?
Thy

This is an S1 thread. You should be able to find some helpful S2 threads if that's what you need.

I bought both models new, back in the day. I still have an S2 running 24/7, using its original power supply. It had issues early on which were fixed by replacing the SD card. I've forgotten all the details, but forum threads at the time were very helpful.
The beeping usually means the device has lost its Ethernet connection. You probably know that each X means one mining chip may not be working, but there could be many underlying causes.

I have had several power supply failures running S1s or S3s on expensive Gold-rated Seasonic 850 PSUs, but no problem with the stock S2 PSU, so you never know.

My main advice is - look for old threads for the model you have - those old threads were full of very specific helpful tips for 'most any problem. For example: https://bitcointalksearch.org/topic/antminer-s2-issues-647398

Good luck!

Thank you for your help. Changed SD card and miner works better. PSU was not the problem. Problem with X is multichain/multishit wallet. Other wallets are no problem and pool minig runs just fine..

aigeezer

legendary

Activity: 1450

Merit: 1013

Cryptanalyst castrated by his government, 1952

Quote from: ErikW79 on July 15, 2016, 05:31:04 PM

I have bought an used S2 miner. Saw it runing and mining, but at home whan I start mining some time after almost all chips show x. And also a beeping noise starts. Any clue what it means?
Thy

This is an S1 thread. You should be able to find some helpful S2 threads if that's what you need.

I bought both models new, back in the day. I still have an S2 running 24/7, using its original power supply. It had issues early on which were fixed by replacing the SD card. I've forgotten all the details, but forum threads at the time were very helpful.
The beeping usually means the device has lost its Ethernet connection. You probably know that each X means one mining chip may not be working, but there could be many underlying causes.

I have had several power supply failures running S1s or S3s on expensive Gold-rated Seasonic 850 PSUs, but no problem with the stock S2 PSU, so you never know.

My main advice is - look for old threads for the model you have - those old threads were full of very specific helpful tips for 'most any problem. For example: https://bitcointalksearch.org/topic/antminer-s2-issues-647398

Good luck!

Darthswan

hero member

Activity: 818

Merit: 508

Quote from: ErikW79 on July 15, 2016, 11:28:50 PM

default enermax revolutions87+. could that be faulty psu?

Could be the PSU. Is it Gold Rated?

ErikW79

full member

Activity: 154

Merit: 100

Quote from: gt_addict on July 15, 2016, 05:38:26 PM

How long was it on when you looked at it? as you could well have been scammed.

My guess is most of the chips start off fine and they die out the longer it's mining. Have you changed any settings at all?

Well I was able to update my miner firmware, Miner chips show ok, mining on pool just fine. But I am able to connect only to stratum. No http connections.

ErikW79

full member

Activity: 154

Merit: 100

Quote from: Darthswan on July 15, 2016, 05:48:42 PM

what type of power supply are you using?

default enermax revolutions87+. could that be faulty psu?

ErikW79

full member

Activity: 154

Merit: 100

Quote from: gt_addict on July 15, 2016, 05:38:26 PM

How long was it on when you looked at it? as you could well have been scammed.

My guess is most of the chips start off fine and they die out the longer it's mining. Have you changed any settings at all?

I was mining only 5h until now. from what I have seen it minig and everything was ok until my own mining 2h. Beeping noise is not anymore. Only the chips showing X.

Darthswan

hero member

Activity: 818

Merit: 508

what type of power supply are you using?

gt_addict

hero member

Activity: 2534

Merit: 623

How long was it on when you looked at it? as you could well have been scammed.

My guess is most of the chips start off fine and they die out the longer it's mining. Have you changed any settings at all?

ErikW79

full member

Activity: 154

Merit: 100

I have bought an used S2 miner. Saw it runing and mining, but at home whan I start mining some time after almost all chips show x. And also a beeping noise starts. Any clue what it means?
Thy

MyRig

donator

Activity: 792

Merit: 510

[email protected]

Good old day S1... Naked weight is 7.5 pounds. Shipping weight on UPS wise it was 8 pounds claim

Quote from: MikeMike on April 27, 2016, 08:26:53 PM

Could someone please tell me what an s-1 ways in a box ready to ship?

Thanks much!

MM

MikeMike

legendary

Activity: 2254

Merit: 1020

★ Ⓚ KORE TEAM Ⓚ ★

Could someone please tell me what an s-1 weighs in a box ready to ship?

Thanks much!

MM

Topic: [Setup & Troubleshoot] Bitmain AntMiner S1 180GH/S miner (Read 452404 times)