[Setup & Troubleshoot] Bitmain AntMiner S1 180GH/S miner - page 64.

icet208

hero member

Activity: 762

Merit: 500

Quote from: Aexcu on March 11, 2014, 12:57:06 PM

Quote from: icet208 on March 11, 2014, 12:35:59 PM

the fan is spinning all the time at 100% speed(if i dont connect the blue wire)...It`s been mining for about 2 weeks at normal speed (only sometimes the fan was spinning at 100%), i stoped the PSU for about 10 min and when i turned on the psu the minerfan didnt start...and then i removed the blue wire from the fan and it spinns all the time at 100%...

I had a similar problem with one of my units. If you're sure that your room is just not too hot (+25'C), you could try what I did:

I connected the FAN to the other blade (S1 has two blades, so there's another connector of the same type at the opposite end on the other blade). I ended up extending the cable and not placing the fan on the other side of the miner, (but I trust that's another way to fix that. Just make sure airflow is to the right direction!)

Hope this helps.

now it works fine..the miner is about 47 degrees...i tried to connect the fan to the other blade but its the same

Epoch

legendary

Activity: 922

Merit: 1003

Quote from: freebit13 on March 11, 2014, 01:59:29 AM

Quote from: Epoch on March 10, 2014, 10:42:48 PM

Quote from: Darthswan on March 10, 2014, 10:24:42 PM

I use a Corsair HX 750, for each of my miners.

I have an HX750. It can power 2 Antminers, though it's only ~86% efficient (@120V) supplying such a large load. I wouldn't recommend it for 2 Ants if you are buying new; I'm only using it because I had it lying around collecting dust.

Thanks for that confirmation that you can run 2 miners from a 750W Epoch. I know it is not as efficient and runs the psu at max, but it's still possible. Just out of interest sake, how long have you been running 2 on a 750W? Are they oc'd at all?

They've been running since Feb 27. No overclock.

Aexcu

full member

Activity: 130

Merit: 100

Quote from: icet208 on March 11, 2014, 12:35:59 PM

the fan is spinning all the time at 100% speed(if i dont connect the blue wire)...It`s been mining for about 2 weeks at normal speed (only sometimes the fan was spinning at 100%), i stoped the PSU for about 10 min and when i turned on the psu the minerfan didnt start...and then i removed the blue wire from the fan and it spinns all the time at 100%...

I had a similar problem with one of my units. If you're sure that your room is just not too hot (+25'C), you could try what I did:

I connected the FAN to the other blade (S1 has two blades, so there's another connector of the same type at the opposite end on the other blade). I ended up extending the cable and not placing the fan on the other side of the miner, (but I trust that's another way to fix that. Just make sure airflow is to the right direction!)

Hope this helps.

icet208

hero member

Activity: 762

Merit: 500

Quote from: freebit13 on March 11, 2014, 12:39:47 PM

Quote from: icet208 on March 11, 2014, 12:35:59 PM

the fan is spinning all the time at 100% speed(if i dont connect the blue wire)...It`s been mining for about 2 weeks at normal speed (only sometimes the fan was spinning at 100%), i stoped the PSU for about 10 min and when i turned on the psu the minerfan didnt start...and then i removed the blue wire from the fan and it spinns all the time at 100%...

Let the miner run for 20 mins to warm up the boards and then push the blue wire back in... does the fan stop or just slow down?

resolved..indeed the fan starts when the temp. rises...didnt knew that...i have an older antminer and the fan was spinning very slow when the temp was that low...
THX

freebit13

hero member

Activity: 616

Merit: 500

I got Satoshi's avatar!

Quote from: icet208 on March 11, 2014, 12:35:59 PM

the fan is spinning all the time at 100% speed(if i dont connect the blue wire)...It`s been mining for about 2 weeks at normal speed (only sometimes the fan was spinning at 100%), i stoped the PSU for about 10 min and when i turned on the psu the minerfan didnt start...and then i removed the blue wire from the fan and it spinns all the time at 100%...

Let the miner run for 20 mins to warm up the boards and then push the blue wire back in... does the fan stop or just slow down?

icet208

hero member

Activity: 762

Merit: 500

the fan is spinning all the time at 100% speed(if i dont connect the blue wire)...It`s been mining for about 2 weeks at normal speed (only sometimes the fan was spinning at 100%), i stoped the PSU for about 10 min and when i turned on the psu the minerfan didnt start...and then i removed the blue wire from the fan and it spinns all the time at 100%...

lenny_

legendary

Activity: 1036

Merit: 1000

DARKNETMARKETS.COM

Quote from: icet208 on March 11, 2014, 12:28:37 PM

heloo
I have a problem with my Antminer S1(180Gh/s). The fan start only when I remove the last wire(blue) and it works at 100% all the time...how can i fix this?
thx

There is temperature threshold to activate fan. Fan is not spinning when miner is cold

icet208

hero member

Activity: 762

Merit: 500

heloo
I have a problem with my Antminer S1(180Gh/s). The fan start only when I remove the last wire(blue) and it works at 100% all the time...how can i fix this?
thx

S4VV4S

hero member

Activity: 1582

Merit: 502

Quote from: Darthswan on March 11, 2014, 05:54:16 AM

Quote from: Epoch on March 10, 2014, 10:42:48 PM

Quote from: Darthswan on March 10, 2014, 10:24:42 PM

I use a Corsair HX 750, for each of my miners.

I have an HX750. It can power 2 Antminers, though it's only ~86% efficient (@120V) supplying such a large load. I wouldn't recommend it for 2 Ants if you are buying new; I'm only using it because I had it lying around collecting dust.

Have you oc'd them?

I doubt it, they would have been fried by now.

Darthswan

hero member

Activity: 818

Merit: 508

Quote from: Epoch on March 10, 2014, 10:42:48 PM

Quote from: Darthswan on March 10, 2014, 10:24:42 PM

I use a Corsair HX 750, for each of my miners.

I have an HX750. It can power 2 Antminers, though it's only ~86% efficient (@120V) supplying such a large load. I wouldn't recommend it for 2 Ants if you are buying new; I'm only using it because I had it lying around collecting dust.

Have you oc'd them?

Raptor2213

full member

Activity: 210

Merit: 100

Quote from: sushi on November 24, 2013, 08:19:30 AM

Even though the Bitmain AntMiner supports built-in Wi-Fi mining, to get the best out of the miner while running Wi-Fi at home, here is an easy solution for you and we tested it for over 24-hours and so far it’s working.

You can use any similar items to make it work. We picked readily available item at the US BestBuy Sotre. Netgear Model#: WNCE2001-100NAS. (Price was $49.99)

If you happens to be living in a dorm, apartment or wherever you can only access to the internet via Wi-Fi, this will make the Bitmain Antminer believe it’s connected to the wired Ethernet and this will not stress the miner.

Bandwidth use during the last 24-hours or more like 36 hours happened to be RX: 38.86 MB (161800 Pkts.) & TX: 14.68 MB (105524 Pkts.)

We purchased the above item to test it out with the Bitmain AntMiner and it worked!

Why would it matter if it is configured to use WiFi or not? Why would this 'stress' the miner?

freebit13

hero member

Activity: 616

Merit: 500

I got Satoshi's avatar!

Quote from: Epoch on March 10, 2014, 10:42:48 PM

Quote from: Darthswan on March 10, 2014, 10:24:42 PM

I use a Corsair HX 750, for each of my miners.

I have an HX750. It can power 2 Antminers, though it's only ~86% efficient (@120V) supplying such a large load. I wouldn't recommend it for 2 Ants if you are buying new; I'm only using it because I had it lying around collecting dust.

Thanks for that confirmation that you can run 2 miners from a 750W Epoch. I know it is not as efficient and runs the psu at max, but it's still possible. Just out of interest sake, how long have you been running 2 on a 750W? Are they oc'd at all?

klondike_bar

legendary

Activity: 2128

Merit: 1005

ASIC Wannabe

Quote from: Swimmer63 on March 10, 2014, 01:58:00 PM

Have not OC'd it yet since I could not get it to work in the first place.

EDIT: SOLVED - Cable issue.

aww you beat me to it - when the cable for the hashing board is loose it simply wont even show a board in the miner.

Epoch

legendary

Activity: 922

Merit: 1003

Quote from: Darthswan on March 10, 2014, 10:24:42 PM

I use a Corsair HX 750, for each of my miners.

I have an HX750. It can power 2 Antminers, though it's only ~86% efficient (@120V) supplying such a large load. I wouldn't recommend it for 2 Ants if you are buying new; I'm only using it because I had it lying around collecting dust.

Darthswan

hero member

Activity: 818

Merit: 508

Quote from: AngusCanine on March 10, 2014, 10:23:08 PM

Is there a PSU available at future shop or best buy that is capable of powering antmineer with out modification, if yes which one if no what PSU should I buy for just a single S1 ?

Never heard of Future shop. Don't know about Best Buy either. Went to Tiger Direct, Fry's Electronics, and Micro Center. I use a Corsair HX 750, for each of my miners.

AngusCanine

legendary

Activity: 1414

Merit: 1001

To weird to live To rare to die

Is there a PSU available at future shop or best buy that is capable of powering antmineer with out modification, if yes which one if no what PSU should I buy for just a single S1 ?

lenny_

legendary

Activity: 1036

Merit: 1000

DARKNETMARKETS.COM

Quote from: kano on March 09, 2014, 05:00:01 PM

Quote from: lenny_ on March 09, 2014, 02:23:40 PM

Can someone share list of frequencies and codes? I don't have my Antminer with me right now, and I am sure that default file did not contain frequencies like 395, 393 or 390, AFAIK.

Thanks in advance!

Con wrote a function in cgminer that does the conversion from integer frequency (for the U1) which of course is also correct for the S1:
https://github.com/ckolivas/cgminer/blob/master/driver-icarus.c#L856

Can you please help me extract this code to run it standalone in single C file, or anything else? I have no skills to write C

Swimmer63

legendary

Activity: 1593

Merit: 1004

Have not OC'd it yet since I could not get it to work in the first place.

EDIT: SOLVED - Cable issue.

freebit13

hero member

Activity: 616

Merit: 500

I got Satoshi's avatar!

Quote from: Swimmer63 on March 10, 2014, 01:51:14 PM

Problem with a brand new miner just received today:

Will not hash. Also will not show Antminer info on the Miner Status page at the bottom. See Photo.
Fan is going full speed as if there is no software control.

I assumed it was a software/firmware issue and updated to the latest firmware. No help.

I am not an IT person, but this is my 14th antminer so I have a lot of experience with this model.

Any opinions, suggestions? Wondering if this is hardware or software.

I've had that problem when I'd typed something incorrectly in the asic-freq file. You did say that you updated the firmware, but I'm not sure if you tried to OC yet at all. I'd say hard reset, but I'm sure you've tried that already.

Swimmer63

legendary

Activity: 1593

Merit: 1004

Problem with a brand new miner just received today:

Will not hash. Also will not show Antminer info on the Miner Status page at the bottom. See Photo.
Fan is going full speed as if there is no software control.

I assumed it was a software/firmware issue and updated to the latest firmware. No help.

I am not an IT person, but this is my 14th antminer so I have a lot of experience with this model.

Any opinions, suggestions? Wondering if this is hardware or software.

Topic: [Setup & Troubleshoot] Bitmain AntMiner S1 180GH/S miner - page 64. (Read 452359 times)