Topic: Swedish ASIC miner company kncminer.com - page 868. (Read 3050071 times)
I meant cut additional holes on the sides of the case in front of the fans for the two rear units and install fans blowing MORE air into the case. I still think you should try switching the location of the hot unit to the front and see how it goes.
Front side has the pretty blinking lights. Either way, it's a lot of air moving that direction. To overpower it, you would need to install two more large fans on the back. If you are actually having a cooling problem, give it a try.
Strange, the back of my case has the blinky lights.
I didn't get instructions to which end was the front and back. It's all relative. I've positions my miner with the air intake side towards the back of the room. The exhaust side blows the hot air out in to the room. Apparently everyone is doing the opposite.
But it should be obvious by my previous explanations that I have NOT doubled up the fans on the intake side or "front" of the case. I merely placed fans in the case where there were none... the exhaust side or "back" of the case.
I had that same idea long before anyone received any miners, but then dropped it.
Might get some cheap 140mm fans and do it after all. Throw in a fan controller too.
If all else fails, try Corsair liquid cooling instead of the standard heatsink.
Front side has the pretty blinking lights. Either way, it's a lot of air moving that direction. To overpower it, you would need to install two more large fans on the back. If you are actually having a cooling problem, give it a try.
Strange, the back of my case has the blinky lights.
I didn't get instructions to which end was the front and back. It's all relative. I've positions my miner with the air intake side towards the back of the room. The exhaust side blows the hot air out in to the room. Apparently everyone is doing the opposite.
But it should be obvious by my previous explanations that I have NOT doubled up the fans on the intake side or "front" of the case. I merely placed fans in the case where there were none... the exhaust side or "back" of the case.
I had that same idea long before anyone received any miners, but then dropped it.
Might get some cheap 140mm fans and do it after all. Throw in a fan controller too.
Hey Cypher... You can actually lower the cooling tower fan, the top of the plastic holder case will easily slide in between the fins, and it will cool dramatically better..... the lower you put it, the better it will cool
I remember reading about this trick before in this thread. I will try next time I move them.Is the heatspreader of the chip still flat? If the cooler was actually damaged while mounted, its reasonable to assume the flimsy alu heatspreader got dented or slightly bent too. Its even possible the heatspreader is no longer making proper contact with (all) the dies. I once had that with an AMD CPU, no matter what cooler I put on it, it would overheat, badly. removing the alu heatspreader solved that. Not sure Id be so brave with such an expensive miner where there are 4 seperate dies under the heatspreader, but I wouldnt mind seeing the pics if you decide to try 
The top of the ASIC chip looks completely flat with no damage. It was the heatsink base that was damaged as each pipe was on a slighty different level, so the total surface wasn't flat.
I changed it with a brand new heatsink and temps didn't improve, but I think the problem might be the spacers as suggested below.
Some of the spacers between the aluminum bar and the board prevent the heatsink from making good contact with the chip. If you twist the heat sink from the top and it moves easily, then it is too loose. I had to remove the spacers on a couple of boards that were hot. Just make sure you don't over-tighten the screws once the spacers are removed.
When I twist it it moves but for a different reason: the screws that go through the custom made plank and the original plank are smaller than the holes, so there is a slight horizontal wobble.Next time I switch it off I will remove the spacer or put shorter ones (plastic ones that came with the heatsink).
Cyper, I don't think blowing across the unit will make a big difference if you close the case. Right now you are bringing fresh air onto that board. Why don't you just strap that fan onto the heatsink on the open side working with the other fan, or switch the location of that board to one of the front slots where they get cold air from the big fans on the front. Otherwise, you could always cut a big hole on the side of the case and mount it properly.
Exactly. If I close the case the back of the side fan will be next to the inside of the aluminium panel, so not enough room to gasp for fresh air.
Do you mean to create a push pull configuration?
From what I see the chip heatspeader doesn't get adequately cooled - probably because of poor contact with the heatsink base or maybe it is way too hot.
I will try all the tricks mentioned here and report back.
Front side has the pretty blinking lights. Either way, it's a lot of air moving that direction. To overpower it, you would need to install two more large fans on the back. If you are actually having a cooling problem, give it a try.
Strange, the back of my case has the blinky lights.
I didn't get instructions to which end was the front and back. It's all relative. I've positioned my miner with the air intake side towards the back of the room. The exhaust side blows the hot air out in to the room. Apparently everyone is doing the opposite.
But it should be obvious by my previous explanations that I have NOT doubled up the fans on the intake side or "front" of the case. I merely placed fans in the case where there were none... the exhaust side or "back" of the case.
so much drama!
I know, seriously why dont 1 of you start a 'KnC groupies and haters' thread?sometimes (but not very often) you get in this thread usefull information if you have KnC devices.
Front side has the pretty blinking lights. Either way, it's a lot of air moving that direction. To overpower it, you would need to install two more large fans on the back. If you are actually having a cooling problem, give it a try.
I attached exhaust fans to the front grill on the inside of my case. I just wired them up to the grill. It really helps to quickly pull the hot air out of the case. I can't understand why KNC didn't do that in the first place. All PCs use a push-pull configuration for air circulation. So why not do the same for an equally hot ASIC miner?
I should think the hash-unit fans create enough positive air pressure. Do you mean you put fans on the back of the unit to pull air out? The front already has fans and it's the input, not output...To me, the back of the case is where the cords come out... pretty much like everything else that we plug in.
The back fans pull cool air in and the heat sink fans push that air through the fins of the heatsink. By the time the air has traveled though the fins it's hot and the velocity has slowed way down. The logical thing to do is try to exhaust that hot air as quickly as possible before it has time to recirculate through the case again, hence the front exhaust fans.
They come with six fans blowing from the front of the case out the very open back, it seems like plenty of cooling to me. They shouldn't need more fans in the back. Not having the case on the miner would disrupt the intended airflow from front to back and probably make cooling worse, unless ambient air temp was very cold (like with mine, still no difference in hashrate). The front units are cooler, the back ones get the hot air from the front and don't get as cool. You could add more fresh air by putting a fan on the side of the case, blowing in front of each rear unit, or divert the hot air around them better. First I'd take the hot one with a problem and move it up front.
I attached exhaust fans to the front grill on the inside of my case. I just wired them up to the grill. It really helps to quickly pull the hot air out of the case. I can't understand why KNC didn't do that in the first place. All PCs use a push-pull configuration for air circulation. So why not do the same for an equally hot ASIC miner?
I should think the hash-unit fans create enough positive air pressure. Do you mean you put fans on the back of the unit to pull air out? The front already has fans and it's the input, not output... Cyper, I don't think blowing across the unit will make a big difference if you close the case. Right now you are bringing fresh air onto that board. Why don't you just strap that fan onto the heatsink on the open side working with the other fan, or switch the location of that board to one of the front slots where they get cold air from the big fans on the front. Otherwise, you could always cut a big hole on the side of the case and mount it properly.
Avenger, I didn't notice you set me straight, all I saw was some lame ad-hominem attack from a sad little boy and didn't need to respond to it. From reading your posts i honestly pity you, it must be hard to live your angry life... You probably need to go outside more, get some fresh air and sunlight.
Bitcoinorama! Good to see you again. Any idea when tuning software will arrive for November units?
Avenger, I didn't notice you set me straight, all I saw was some lame ad-hominem attack from a sad little boy and didn't need to respond to it. From reading your posts i honestly pity you, it must be hard to live your angry life... You probably need to go outside more, get some fresh air and sunlight.
Bitcoinorama! Good to see you again. Any idea when tuning software will arrive for November units?
I attached exhaust fans to the front grill on the inside of my case. I just wired them up to the grill. It really helps to quickly pull the hot air out of the case. I can't understand why KNC didn't do that in the first place. All PCs use a push-pull configuration for air circulation. So why not do the same for an equally hot ASIC miner?
Cyper, I don't think blowing across the unit will make a big difference if you close the case. Right now you are bringing fresh air onto that board. Why don't you just strap that fan onto the heatsink on the open side working with the other fan, or switch the location of that board to one of the front slots where they get cold air from the big fans on the front. Otherwise, you could always cut a big hole on the side of the case and mount it properly.
Avenger, I didn't notice you set me straight, all I saw was some lame ad-hominem attack from a sad little boy and didn't need to respond to it. From reading your posts i honestly pity you, it must be hard to live your angry life... You probably need to go outside more, get some fresh air and sunlight.
Bitcoinorama! Good to see you again. Any idea when tuning software will arrive for November units?
Avenger, I didn't notice you set me straight, all I saw was some lame ad-hominem attack from a sad little boy and didn't need to respond to it. From reading your posts i honestly pity you, it must be hard to live your angry life... You probably need to go outside more, get some fresh air and sunlight.
Bitcoinorama! Good to see you again. Any idea when tuning software will arrive for November units?
so much drama!
I know, seriously why dont 1 of you start a 'KnC groupies and haters' thread?
so much drama!
BTC PRICE IS CRASHED DOWN
You're right. Shill is the wrong word ( and kind if offensive too) heavy supporter maybe... And I also should have put "from my perspective". I hope you can see it from my point of view. No offence meant orama
No worries. There really isn't anything underhand going on. Simply I liked the bunch of guys, and what I saw. They are very competent engineers. That's no longer questionable. I've been fair to every company and using common sense called out questionable behaviour. I've been right about every red flag I've seen.
Avenger, trust me I'm still pissed at them for the whole upgrade fiasco but I just got tired of complaining. Lol. You seem like a decent guy who got burned and I have been in the same spot. It's the morning and didn't have my coffee. Guess I was just cranky. Lol
You're right. Shill is the wrong word ( and kind if offensive too) heavy supporter maybe... And I also should have put "from my perspective". I hope you can see it from my point of view. No offence meant orama
Avenger, i apologize for attacking you like that sorry it was uncalled for and you are right. You have never said anything bad to me either. I am just getting frustrated as everything I log in it's all I see. Orama was a pretty obvious knc shill albeit a very helpful one. Phoenix tho isn't but just a die hard knc cheerleader, maybe that got him some preferential treatment but honestly big deal. This company is new and plays favourites plus people (such as myself) are bending over backwards to get their products so they have the power. Ah well. It's just tiring.
I appeciate the apology asic-k. You are one of the very few people on here who has had the backbone to offer one when they realised they were being unfair.
In the past 17 days I've made only 37 posts in this thread - about 2 per day. So the noise is not me. Maybe it's more noticeable because I don't mince my words, but I don't have that much time for this forum, I have other things to do.
There are certain other people - it might be easy enough to guess who - that have made 100's + 100's of posts in the same period of time. They are a drain on everyone with their constant wittering, fight picking and it certainly is tiring.
After I added the additional side fan to the "hot as the surface of the sun" die now it is getting adequately cooled, but the fan is just standing there not secured in any way and I can't even put the lid on.
https://i.imgur.com/EVURj5e.jpg
https://i.imgur.com/4Hn0sx8.jpg
https://i.imgur.com/EVURj5e.jpg
https://i.imgur.com/4Hn0sx8.jpg
Some of the spacers between the aluminum bar and the board prevent the heatsink from making good contact with the chip. If you twist the heat sink from the top and it moves easily, then it is too loose. I had to remove the spacers on a couple of boards that were hot. Just make sure you don't over-tighten the screws once the spacers are removed.
Jump to: