Topic: ⚡[ANN]⚡ ▐░Espers [ESP]░▌▐░PoW/PoS░▌▐░HMQ1725 Algo░▌ ▐░New Features░▌ - page 414. (Read 923924 times)

You can try using the commandline client to make a little batch for sending a lot of small amounts.

At first i was able to send 3 million to Novaexchange.
But then the limit got smaller to 1 million, and then the sending limit got even smaller and smaller after several transactions.
Now my limit got down to 20,000.

With the sending limit getting down after each transactions, this will took me months or year to send all my ESP1 to Novaexchange.
Plus my ESP1 wallet is too slow and always crash or stuck.
There need a better way to exchange my ESP1 to ESP2....i don't want to lose all my ESP1 when the deadline over 

Why only 20k.  Largest amount I sent do far to nova Is 50 million. What was the error message you get?

I'm not a coder or a tech guy, so I need some help with converting my ESP1 into ESP 2.0.
With the ESP1 wallet i only able to send less then 20,000 ESP1 to Novaexchange, to exchange for ESP 2.0.
And i have 700 millions ESP1 in  my wallet, with this current rate, i need several months or a year to transfer all my ESP1 to Novaexchange.
Plus my ESP1 wallet is also very slow and always crash or stuck.
So when the deadline come i will loss all my ESP1 

Is there a way, the admin can help me to covert all my ESP1 to ESP2?....i can send my wallet.dat backup if that help.
I already PM for help, but not body respond or help.
Hope the admins can help find a way to covert all my ESP1 into ESP2.
I invest a lots into this coins in the beginning, and i don't want to lose my coins when the deadline ended 

OP will be reworked at some point, currently it get's the job done (defining ESP1 and ESP2 files).
However, it definitely isn't what we want end-game.



Thank you Just a matter of time.

nice to hear that we are realy going closer dev, good luck.

OP need sensible creator and corrector. 

Lol, a bit of a typo of wallet resides! 

T.

@Everyone

A quick news update. Today we all took it kind of slow and handled quite a few logistical things.
Over the course of the next few days mining will be integrated and then we will move onto messaging. Thank you all who are a part of this project!

We look forward to the future.

lol  it's bad recipe 
for case "WALLET IN 192.168.188.65" and "MINER IN 192.168.188.99" Espers.conf must content !!!!

 

Awesome! Thank you very much for being a part of the project





We'll look into it




Thank you very much for assisting other community members, we are not always able to and it helps greatly to have users like you.

hi guys, pos working pretty well and with the low difficulty im hitting a few blocks a day on an dated i5!!  

Any chance we could get setstakesplitthreshold implemented in a future update? that's if its not already planned in

Pallas version from OP works:

For Wallet resides on 192.168.188.65

rpcallowip=192.168.178.*

sgminer.exe -k hmq1725 -o 192.168.178.65:22442 -u insertfunkyname -p secretone -g 1 -I 14 -s 1 --more-notices --fix-protocol

T,

10:1 was the arbitrary figure used at the time, I remember no other suggestions from the community like 1000:1. I have seen some  concern that even at 10:1 Espers moves away from original intent so maybe more than 10:1 would have been too extreme. Once the development and features put into Espers are realised I think the coin will show its strength

T.

Now it is clear. I about swap have read only today therefore I have been surprised.

We had a google hangout meeting to which everyone was invited (it was a few weeks back).
After that meeting the meeting minutes were taken and the team came to a decision based upon community feedback.
As the decisions have already been made and the token swapping we will leave the chain alone as far as the count is concerned.

Why swap 10:1 many would like 1000:1 to clean excess zeros?

Where your miner is reside?

hi@all!

i think, i need your help...

don't want to steal your time, so i will keep it short.

possible to mine with gpu, using the latest client?  if not, just type "no" and don't read on 

you say it works fantastic without any problems, then please read on.

i can't get this running. i read this thread up and down, my eyes are swollen and i have the feeling to go mad (slow, but steady )
i am not that "one try and good bye give-up guy"! (setting up cpu-miner worked without any issues)
ok, back to "keep it short"

these are my thoughts...
- getwork/stratum problem? maybe gpu-miner doesn't support getwork? (tried different ones) need to run some special software for that?
- using wrong port or wrong nodes? which ports to put in espers.conf and where to point the miner?
my espers.conf looks like this:                 

listen=1
server=1
port=22448
rpcport=22442
rpcuser=insertfunkyname
rpcpassword=secretone
rpcallowip=localhost
addnode=104.236.150.155:22448
addnode=159.203.24.196:22448
addnode=46.101.188.194:22448
addnode=173.18.196.253:22448
addnode=208.68.36.6:22448
addnode=146.185.153.196:22448
addnode=188.166.155.131:22448
addnode=107.170.212.222:22448
addnode=159.203.12.73:22448

starting miner, getting error message saying sth. like "forgot to set up worker? using wrong port?..."
thank you, software! good that you ask me, if i did sth. wrong. telling me what the problem is...no...would be to easy   

maybe someone can help with this.

Never made one for the old client. Will try to get around to it through everything else.