All 110V users
Hello to all our new world clients.
It looks like for the 110V the optimal starting voltage is 0.650V or even 0.645V.
Please update your settings and you might get better hashing rate (wait for 30 minutes after reset to see where miner settles).
Topic: [ANN] Spondoolies-Tech - carrier grade, data center ready mining rigs - page 583. (Read 1260354 times)
June 09, 2014, 09:49:57 AM
June 09, 2014, 07:51:46 AM
very nice article at Coindesk on Spondoolies RockerBox ASIC inside SP30 miner.
http://www.coindesk.com/details-spondoolies-tech-new-bitcoin-mining-asic-leaked-online/
very exciting times, can't wait to see them
http://www.coindesk.com/details-spondoolies-tech-new-bitcoin-mining-asic-leaked-online/
very exciting times, can't wait to see them
June 09, 2014, 07:48:15 AM
Hey Zvi,
i had one of my SP10 units temporarily installed till we get the new air conditioner in the storage room.
Last night it stopped hashing so I checked on it this morning.
Suprisingly I found out that it took a dive off the shelf from about 1m height and landed between some pallets.
The damage is only cosmetic but I'm posting the pictures to tell me if you think I should open it and check something inside.
It seems to hash OK although the power on AC2DC doesn't go up to 1265. I had the same issue about 1 week ago and with a couple reboots it started to go up again. Currently it's hashing at 1.37Th/s - while it normally hashes at 1.42TH/s.
Note that it is plugged in with a lot of other devices so the power again might not be enough. This will be solved when the new air conditioner is installed and moved to its place. Let me know if you think something else is at fault.
Here is AC2DC value:
AC2DC power=1208[1265], temp=0, leading zeroes=39
i had one of my SP10 units temporarily installed till we get the new air conditioner in the storage room.
Last night it stopped hashing so I checked on it this morning.
Suprisingly I found out that it took a dive off the shelf from about 1m height and landed between some pallets.
The damage is only cosmetic but I'm posting the pictures to tell me if you think I should open it and check something inside.
It seems to hash OK although the power on AC2DC doesn't go up to 1265. I had the same issue about 1 week ago and with a couple reboots it started to go up again. Currently it's hashing at 1.37Th/s - while it normally hashes at 1.42TH/s.
Note that it is plugged in with a lot of other devices so the power again might not be enough. This will be solved when the new air conditioner is installed and moved to its place. Let me know if you think something else is at fault.
Here is AC2DC value:
AC2DC power=1208[1265], temp=0, leading zeroes=39
We did not test this usage scenario, so it is hard for me to advise
Please post your ASIC stats page and DCR page.
June 09, 2014, 03:03:06 AM
SP30 dimensions:
554 X 431 X 88.4 [mm]
SP10 dimensions:
473 X 431 X 55.1 [mm]
Is that Depth x Width x Height?554 X 431 X 88.4 [mm]
SP10 dimensions:
473 X 431 X 55.1 [mm]
So the SP30 is deeper (longer case) than the SP10? (And 2U vs 1.25U)
Yes and Yes. Information about mounting solution will be published soon.
June 09, 2014, 01:57:55 AM
SP30 dimensions:
554 X 431 X 88.4 [mm]
SP10 dimensions:
473 X 431 X 55.1 [mm]
Is that Depth x Width x Height?554 X 431 X 88.4 [mm]
SP10 dimensions:
473 X 431 X 55.1 [mm]
So the SP30 is deeper (longer case) than the SP10? (And 2U vs 1.25U)
June 09, 2014, 01:49:42 AM
SP30 dimensions:
554 X 431 X 88.4 [mm]
SP10 dimensions:
473 X 431 X 55.1 [mm]
554 X 431 X 88.4 [mm]
SP10 dimensions:
473 X 431 X 55.1 [mm]
June 09, 2014, 01:28:07 AM
Hey Zvi,
i had one of my SP10 units temporarily installed till we get the new air conditioner in the storage room.
Last night it stopped hashing so I checked on it this morning.
Suprisingly I found out that it took a dive off the shelf from about 1m height and landed between some pallets.
The damage is only cosmetic but I'm posting the pictures to tell me if you think I should open it and check something inside.
It seems to hash OK although the power on AC2DC doesn't go up to 1265. I had the same issue about 1 week ago and with a couple reboots it started to go up again. Currently it's hashing at 1.37Th/s - while it normally hashes at 1.42TH/s.
Note that it is plugged in with a lot of other devices so the power again might not be enough. This will be solved when the new air conditioner is installed and moved to its place. Let me know if you think something else is at fault.
Here is AC2DC value:
AC2DC power=1208[1265], temp=0, leading zeroes=39
i had one of my SP10 units temporarily installed till we get the new air conditioner in the storage room.
Last night it stopped hashing so I checked on it this morning.
Suprisingly I found out that it took a dive off the shelf from about 1m height and landed between some pallets.
The damage is only cosmetic but I'm posting the pictures to tell me if you think I should open it and check something inside.
It seems to hash OK although the power on AC2DC doesn't go up to 1265. I had the same issue about 1 week ago and with a couple reboots it started to go up again. Currently it's hashing at 1.37Th/s - while it normally hashes at 1.42TH/s.
Note that it is plugged in with a lot of other devices so the power again might not be enough. This will be solved when the new air conditioner is installed and moved to its place. Let me know if you think something else is at fault.
Here is AC2DC value:
AC2DC power=1208[1265], temp=0, leading zeroes=39
June 09, 2014, 01:08:47 AM
Ok here are the videos (aka "how to silence your SP10"):
UCoustic rack cabinet part 1
UCoustic rack cabinet part 2
UCoustic rack cabinet part 1
UCoustic rack cabinet part 2
ERRRMERRRGUUURD NEED THAT CABINET.
Edit: nevermind, costs $5k and weights 300kg for the 42U version!
can't you ask them for an evaluation unit?
June 09, 2014, 01:07:53 AM
Specs on the 80mm fans? They look like 80x80x38mm ?
I have two Delta fans in a 4u case and they are loud. These will likely be plenty loud but avoid the higher pitch "whine" of the SP10s?
I have two Delta fans in a 4u case and they are loud. These will likely be plenty loud but avoid the higher pitch "whine" of the SP10s?
Early measurements shows that from 1m distance the SP30 noise level will be ~68dB (PSU side, fans at 80%, power supplies at max load). We'll have exact figures only when the ASICs will arrive.
Under same conditions, the SP10 noise level is ~74dB
The fans specs: https://www.dropbox.com/s/xf4j86aceagk50t/FD128038HB-S%282W7YM%29%2BC-ROHS.PDF
June 09, 2014, 12:46:34 AM
Hi all.
As you seen from the pictures today the SP30 boards have arrived, and I am starting to work on its FW.
From this moment on Remo (remo@) will be handling the customer support and the SP10 releases.
I am grateful for all the kind words I got on this forum.
It does not mean that Spondoolies will stop developing SP10 FW.
In the next FW version we will actually add 3 new and very exciting features
As you seen from the pictures today the SP30 boards have arrived, and I am starting to work on its FW.
From this moment on Remo (remo@) will be handling the customer support and the SP10 releases.
I am grateful for all the kind words I got on this forum.
It does not mean that Spondoolies will stop developing SP10 FW.
In the next FW version we will actually add 3 new and very exciting features
when is next firmware released?
I love surprises
June 08, 2014, 11:41:04 PM
I know I keep thinking of how happy my wife would be. LOL
Plus it is so dam cool.
ERRRMERRRGUUURD NEED THAT CABINET.
Edit: nevermind, costs $5k and weights 300kg for the 42U version!
Plus it is so dam cool.
Ok here are the videos (aka "how to silence your SP10"):
UCoustic rack cabinet part 1
UCoustic rack cabinet part 2
UCoustic rack cabinet part 1
UCoustic rack cabinet part 2
ERRRMERRRGUUURD NEED THAT CABINET.
Edit: nevermind, costs $5k and weights 300kg for the 42U version!
June 08, 2014, 08:45:48 PM
The scuttlebutt from somebody who's been to their office there near the Gaza Strip with the two abandoned buses out front, assures me that they're the real McCoy, in spite of not having an office comparable to some ritzy place. (again, not a diss, but letting you and them know that I'm keeping a pretty good eye on them)
~Bruno Kucinskas
One abandoned bus, which we really don't understand it's purpose. It's not out front but about 200 meters. It's out front HP Indigo more or less.
Anyway, we're 400 meters from Intel 22nm FAB, so it's not that deserted place.
We're about 25 KM from Gaza strip, not in any disputed territory.
We have update on the abandoned bus as well. It seems that it being re-purpose by someone as a cantina:
Hahahahaa... Oh man you guys at Spondoolies never miss a beat. Cripes ahahahah.
June 08, 2014, 06:51:16 PM
Ok here are the videos (aka "how to silence your SP10"):
UCoustic rack cabinet part 1
UCoustic rack cabinet part 2
UCoustic rack cabinet part 1
UCoustic rack cabinet part 2
ERRRMERRRGUUURD NEED THAT CABINET.
Edit: nevermind, costs $5k and weights 300kg for the 42U version!
June 08, 2014, 05:34:20 PM
Can you organize a group buy for SP30 September batch Roadstress? I'm sure folks would be interested if the price was right.
June 08, 2014, 04:22:10 PM
Hi All, i got SP10 , back unit shows tempreture 75c , that normal or need stop mining . Now in UK bit hot . Thanks
. ThanksIt's ok.
Thanks !
June 08, 2014, 04:07:53 PM
Hi All, i got SP10 , back unit shows tempreture 75c , that normal or need stop mining . Now in UK bit hot . Thanks
. ThanksIt's ok.
June 08, 2014, 04:00:11 PM
Hi All, i got SP10 , back unit shows tempreture 75c , that normal or need stop mining . Now in UK bit hot . Thanks
. Thanks June 08, 2014, 03:37:25 PM
Specs on the 80mm fans? They look like 80x80x38mm ?
I have two Delta fans in a 4u case and they are loud. These will likely be plenty loud but avoid the higher pitch "whine" of the SP10s?
I have two Delta fans in a 4u case and they are loud. These will likely be plenty loud but avoid the higher pitch "whine" of the SP10s?
June 08, 2014, 03:08:51 PM
Hi all.
As you seen from the pictures today the SP30 boards have arrived, and I am starting to work on its FW.
From this moment on Remo (remo@) will be handling the customer support and the SP10 releases.
I am grateful for all the kind words I got on this forum.
It does not mean that Spondoolies will stop developing SP10 FW.
In the next FW version we will actually add 3 new and very exciting features
As you seen from the pictures today the SP30 boards have arrived, and I am starting to work on its FW.
From this moment on Remo (remo@) will be handling the customer support and the SP10 releases.
I am grateful for all the kind words I got on this forum.
It does not mean that Spondoolies will stop developing SP10 FW.
In the next FW version we will actually add 3 new and very exciting features
June 08, 2014, 01:59:22 PM
thanks for the update and sexy asic-porn
I'm pretty sure that screen command needs to be installed and implemented correctly to display cgminer like screenshot above right.
No rush, if it could be done for a future firmware upgrade would be great.
Cheers
merv77
No rush, if it could be done for a future firmware upgrade would be great.
Cheers
merv77
I believe (and correct me if I'm wrong, people) that cgminer needs to be compiled with "ncurses" support in order to generate the interface you are wanting. "Screen" allows for textual 'multitasking' in a CLI environment, and is useful for running a CLI-based program in the 'background' on a single SSH session.
https://github.com/ckolivas/cgminer (search for ncurses)
This is true.
I will see if I can add it next image.
thanks zvisha this would be fantastic
Jump to: