[ANN] TeamRedMiner v0.10.10 - Ironfish/Kaspa/ZIL/Kawpow/Etchash and More - page 40.

coinminery

newbie

Activity: 23

Merit: 0

Quote from: Iamtutut on September 29, 2020, 10:52:02 AM

Quote from: coinminery on September 29, 2020, 09:29:56 AM

Quote from: Iamtutut on September 27, 2020, 03:09:29 PM

Quote from: coinminery on September 27, 2020, 10:26:58 AM

Hi
Failed to initialize device idx 0 (-47)
RX5500XT and RX 5600XT
http://prntscr.com/uofgzi

Check which number of the PCI-E slots your GPUs are connected to.

1. What's the difference in connectors?
If you forcibly disable the device in the parameters, then there will be an error on the second device (1) - Failed to initialize device idx 1 (-47).
2. There are no problems in the ether mining mode.

Your GPU PCI-E slots are 0; 1; 2; 3...(My mobo has 5 PCI-E slots). Did you map them correctly so that TRM is not trying to use a slot where no GPU is connected ?

Also, Is the algo you're trying to mine actually supported by TRM on both of your GPUs ?

1. Claymore ETH OK! - http://prntscr.com/usycrn
2. TeamRedMiner ETH OK! - http://prntscr.com/usyf5s
3. TeamRedMiner HVN NO OK!!! - http://prntscr.com/usyge9
The question is, does the miner support these cards at all or not Huh

DrX

member

Activity: 233

Merit: 20

Quote from: yoonline on October 03, 2020, 08:15:06 PM

Quote from: DrX on October 03, 2020, 12:52:31 AM

Quote from: yoonline on October 02, 2020, 11:45:57 PM

4gb card stopped working today, fix?

Try to restart miner, it should work fine.

And check the GitHub, there is new version Team Red Miner v0.7.12

nothing, all my 4gb rig stopped working with eth

Maybe some extra info would help, driver version? windows performance settings (visual effects and virtual memory)? system env settings added?

tale01

newbie

Activity: 121

Merit: 0

Quote from: yoonline on October 03, 2020, 08:15:06 PM

Quote from: DrX on October 03, 2020, 12:52:31 AM

Quote from: yoonline on October 02, 2020, 11:45:57 PM

4gb card stopped working today, fix?

Try to restart miner, it should work fine.

And check the GitHub, there is new version Team Red Miner v0.7.12

nothing, all my 4gb rig stopped working with eth

Used Linux OS, gpu 4gb run smoothly Wink

yoonline

newbie

Activity: 51

Merit: 0

Quote from: DrX on October 03, 2020, 12:52:31 AM

Quote from: yoonline on October 02, 2020, 11:45:57 PM

4gb card stopped working today, fix?

Try to restart miner, it should work fine.

And check the GitHub, there is new version Team Red Miner v0.7.12

nothing, all my 4gb rig stopped working with eth

DrX

member

Activity: 233

Merit: 20

Quote from: yoonline on October 02, 2020, 11:45:57 PM

4gb card stopped working today, fix?

Try to restart miner, it should work fine.

And check the GitHub, there is new version Team Red Miner v0.7.12

yoonline

newbie

Activity: 51

Merit: 0

4gb card stopped working today, fix?

Iamtutut

full member

Activity: 1120

Merit: 131

Quote from: coinminery on September 29, 2020, 09:29:56 AM

Quote from: Iamtutut on September 27, 2020, 03:09:29 PM

Quote from: coinminery on September 27, 2020, 10:26:58 AM

Hi
Failed to initialize device idx 0 (-47)
RX5500XT and RX 5600XT
http://prntscr.com/uofgzi

Check which number of the PCI-E slots your GPUs are connected to.

1. What's the difference in connectors?
If you forcibly disable the device in the parameters, then there will be an error on the second device (1) - Failed to initialize device idx 1 (-47).
2. There are no problems in the ether mining mode.

Your GPU PCI-E slots are 0; 1; 2; 3...(My mobo has 5 PCI-E slots). Did you map them correctly so that TRM is not trying to use a slot where no GPU is connected ?

Also, Is the algo you're trying to mine actually supported by TRM on both of your GPUs ?

coinminery

newbie

Activity: 23

Merit: 0

Quote from: Iamtutut on September 27, 2020, 03:09:29 PM

Quote from: coinminery on September 27, 2020, 10:26:58 AM

Hi
Failed to initialize device idx 0 (-47)
RX5500XT and RX 5600XT
http://prntscr.com/uofgzi

Check which number of the PCI-E slots your GPUs are connected to.

1. What's the difference in connectors?
If you forcibly disable the device in the parameters, then there will be an error on the second device (1) - Failed to initialize device idx 1 (-47).
2. There are no problems in the ether mining mode.

fmz89

legendary

Activity: 1764

Merit: 1002

Quote from: Janisalamat on September 09, 2020, 07:00:31 AM

I use teamredminer 0.7.9 for mining using 3 vega 56 gpus. I get this command always.. Please someone help...
And one GPU mostly gets off even for different miners.. Please someone help. Thanks in advance

GPU 1: detected DEAD ..... No restart script configured, will continue mining.
Please use command line argument --watchdog_script to handle dead GPUs.

your mem setting need to lower

Iamtutut

full member

Activity: 1120

Merit: 131

Quote from: coinminery on September 27, 2020, 10:26:58 AM

Hi
Failed to initialize device idx 0 (-47)
RX5500XT and RX 5600XT
http://prntscr.com/uofgzi

Check which number of the PCI-E slots your GPUs are connected to.

coinminery

newbie

Activity: 23

Merit: 0

Hi
Failed to initialize device idx 0 (-47)
RX5500XT and RX 5600XT
http://prntscr.com/uofgzi

GrayCatt

newbie

Activity: 27

Merit: 0

Quote from: kerney666 on August 16, 2020, 11:06:45 AM

Trying to Mine KawPow with TRM on MiningPoolhub,

Ok, I checked quickly. Afai can see, miningpoolhub is sending garbage seed hashes, except for one time when I started the miner, then it was correct.

OК, then. NBminer works KAWPOW on MiningPoolhub. XMRig miner works KAWPOW on MiningPoolhub. I assume, there must be a way to make TRM work KAWPOW on MiningPoolhub! Roll Eyes

May be, some command-line parameter to ignore "garbage seed hashes"?

Janisalamat

newbie

Activity: 13

Merit: 0

Quote from: livada on September 09, 2020, 02:24:57 PM

Quote from: Janisalamat on September 09, 2020, 07:00:31 AM

I use teamredminer 0.7.9 for mining using 3 vega 56 gpus. I get this command always.. Please someone help...
And one GPU mostly gets off even for different miners.. Please someone help. Thanks in advance

GPU 1: detected DEAD ..... No restart script configured, will continue mining.
Please use command line argument --watchdog_script to handle dead GPUs.

i see this message on 1 GPU(vega56 hynix) on rig. to low MV on memory. try 900mv and see. after work godown to 890mv and go down to 880 ....
my other GPU use 850-860mv and work but 1 GPU work only with 890mv without this message.

if use watchdog_script rig go restart miner and work again. use this command and create restart.bat

teamredminer.exe -a ethash -o stratum+tcp://daggerhashimoto.eu.nicehash.com:3353 -u WALETADRES -p PASS -d 0,1,2,3,4,5 --eth_config A896 --bus_reorder --watchdog_script=restart.bat

in restart. bat write this:

echo.
timeout 6
taskkill /F /IM "teamredminer.exe"
timeout 3
start "start.bat" "start.bat"
echo.
timeout 5
exit

Thank you so much Kiss

Both of you Livanda, BogdanCo. Yeah I thing the software may some time create issues or ethash DAG, Actually with watchdog_script I couldn't handle the issue well, but by decreasing the memory clock and core clock till 890 mV and 1300 MHz it become stable till some how, I think the drivers 19.2.1 were also not stable for it.
Grateful to you both. Stay energetic!

livada

newbie

Activity: 417

Merit: 0

Quote from: Janisalamat on September 09, 2020, 07:00:31 AM

I use teamredminer 0.7.9 for mining using 3 vega 56 gpus. I get this command always.. Please someone help...
And one GPU mostly gets off even for different miners.. Please someone help. Thanks in advance

GPU 1: detected DEAD ..... No restart script configured, will continue mining.
Please use command line argument --watchdog_script to handle dead GPUs.

i see this message on 1 GPU(vega56 hynix) on rig. to low MV on memory. try 900mv and see. after work godown to 890mv and go down to 880 ....
my other GPU use 850-860mv and work but 1 GPU work only with 890mv without this message.

if use watchdog_script rig go restart miner and work again. use this command and create restart.bat

teamredminer.exe -a ethash -o stratum+tcp://daggerhashimoto.eu.nicehash.com:3353 -u WALETADRES -p PASS -d 0,1,2,3,4,5 --eth_config A896 --bus_reorder --watchdog_script=restart.bat

in restart. bat write this:

echo.
timeout 6
taskkill /F /IM "teamredminer.exe"
timeout 3
start "start.bat" "start.bat"
echo.
timeout 5
exit

BogdanCo

hero member

Activity: 729

Merit: 513

Quote from: Janisalamat on September 09, 2020, 07:00:31 AM

I use teamredminer 0.7.9 for mining using 3 vega 56 gpus. I get this command always.. Please someone help...
And one GPU mostly gets off even for different miners.. Please someone help. Thanks in advance

GPU 1: detected DEAD ..... No restart script configured, will continue mining.
Please use command line argument --watchdog_script to handle dead GPUs.

I would say to use the watchdog script into the command line, so in case of a Dead GPU the whole rig will be restarted.

I noticed recently (maybe because of DAG increase on ETH!?) that old OC settings (which were working stable in the last 1-2 years) for Vega 56 or 64 are not good anymore. Either you have to increase voltage a little or reduce the OC.... Still struggle to find a good and stable OC setting. If someone has one please share it.

Janisalamat

newbie

Activity: 13

Merit: 0

I use teamredminer 0.7.9 for mining using 3 vega 56 gpus. I get this command always.. Please someone help...
And one GPU mostly gets off even for different miners.. Please someone help. Thanks in advance

GPU 1: detected DEAD ..... No restart script configured, will continue mining.
Please use command line argument --watchdog_script to handle dead GPUs.

livada

newbie

Activity: 417

Merit: 0

Quote from: Iamtutut on September 07, 2020, 01:46:07 AM

That's what I did, it's not working

teamredminer.exe -a ethash -o stratum+tcp://daggerhashimoto.eu.nicehash.com:3353 -u 3***********************P -p x -d 0,

Whether I set -d 0, or any other number, the miner crash starts.

dont use -d 0 and miner start with all card
or if you use command is -d 0 without ,
if use 2 card command is -d 0,1 or -d 3,5

etc miner with 6 card

teamredminer.exe -a ethash -o stratum+tcp://daggerhashimoto.eu.nicehash.com:3353 -u WALETADRES -p PASS -d 0,1,2,3,4,5 --eth_config A896 --bus_reorder --watchdog_script=restart-eth.bat

Iamtutut

full member

Activity: 1120

Merit: 131

That's what I did, it's not working

teamredminer.exe -a ethash -o stratum+tcp://daggerhashimoto.eu.nicehash.com:3353 -u 3***********************P -p x -d 0,

Whether I set -d 0, or any other number, the miner crash starts.

alucard20724

sr. member

Activity: 703

Merit: 272

Quote from: Iamtutut on September 07, 2020, 12:18:38 AM

I can't get TRM to work on my second miner and I don't get why. I have no APU on my other rig, so I launch all GPUs.

It's a Ryzen 2400G APU (win 10 pro, 12GB ram) with a Vega 64. Obviously, I intend to mine only with the Vega 64, mining etash.

Both are listed as following:

The Vega 64 : miner 0 platform 0 opencl 0
The Vega 11 cores: miner 1 platform 0 opencl 1

What should be the command line to launch the Vega 64 only ?

Thanks

set it to -d 0, if it starts mining on the apu, then switch it to -d 1.
i have the 2400G apu also.

Iamtutut

full member

Activity: 1120

Merit: 131

I can't get TRM to work on my second miner and I don't get why. I have no APU on my other rig, so I launch all GPUs.

It's a Ryzen 2400G APU (win 10 pro, 12GB ram) with a Vega 64. Obviously, I intend to mine only with the Vega 64, mining etash.

Both are listed as following:

The Vega 64 : miner 0 platform 0 opencl 0
The Vega 11 cores: miner 1 platform 0 opencl 1

What should be the command line to launch the Vega 64 only ?

Thanks

Topic: [ANN] TeamRedMiner v0.10.10 - Ironfish/Kaspa/ZIL/Kawpow/Etchash and More - page 40. (Read 211877 times)