Topic: [ANN][POOL] Mining Pool Hub - Multipool. Multialgo, Auto Exchange to any coin. - page 202. (Read 487870 times)

Monero seems to be having problems with manual payout and auto-exchange. Im piling up quite the collection and need to get that $$$

I'm a little confused can anyone clarify my understanding of Auto-Switch on MPH.

Here is my understanding of the "Quick start guide".

"Algo switch mining (Port 17XXX)."
So this would switch only between coins of the *SAME* Algo such as; ETH, Musicoin, Expanse...and so on.

"Multi-algo switch mining (Port 12XXX)."
So this would switch between coins of *DIFFERENT* Algo's such as; Ethash, Cryptonight, NeoScrypt...and so on.

...but I have Claymore config as below, and I see it switching between the Ethash algo's only (ETC, ETH & Expanse) - just as I want it to; so what's the difference between using ports 12xxx & 17xxx if I'm only mining Ethash algo coins - or is there any ?

EthDcrMiner64 -epool europe.ethash-hub.miningpoolhub.com:12020 -ewal . -eworker . -esm 2 -epsw x -allpools 1 -allcoins 1 -ftime 10

The similar situation.
Yesterday i move my BCH to autoexchange, transfer ID 8065330   
24h no autoexchange, is it normal?

Where can I find the transaction data, because it seemed like it just disappeared.  I have no transaction history of BCC leaving my BCC wallet.  when BCC autoexchange was first enabled, it sat on "Credited for Auto Exchange" for five days and did nothing.  After 5 days I moved it back to my wallet which took less than 30 minutes.  After it was back on my wallet, I chose to auto exchange it again.  30 minutes later is was completely gone with no trace.  what happened to it?

I think that means you are a donator.

under contributor hashrates on the pool stat page, why do I have a star next to my name?sometimes I see others with a star as well

I've just watched my miner switch and looking on MPH there was some Expanse as well as my original Ethereum, so looks like the switching works.
Having a bit of a think about it and I think port 12023 is for auto-switching between Ethash algorithm coins and port 17xxx is for switching between different algorithm coins.

I could be wrong, but I believe the 12XXX ports are if you want to manually switch using the hub worker feature, and 17XXX is the autoswitch that takes all the complication out of it.

I thought it was "europe.equihash-hub.miningpoolhub.com:12023" for Ethash switching.
I've just started trying the auto-switch for Ethash only and set miner to port 12023, should it be port 17020 ?
..and set "Account's Default Job" to "Ethash" ...I'm a bit confused.

are you mining on ethereum only port or on 17020 for most profitable ETHash coin?

0.2 ETH after two days of mining (~400 MH). Nice.  I'll stay here for a while. Stay away of Alpereum, by the way. 

I'll update and resync.




Please try it again. I upgraded server and lowered difficulty level for most ports.





api calls are cached upto 30 minutes. This is why two api pages can show different numbers.





I'll reply you back. I get email too many emails daily.






Is 30 minutes delay harming profit?

That api call is cached and only affects per algo.
If you are mining ethash, then internal profit switching is done in realtime without disconnection. It's done seamlessly.

If you switch several algo ports frequently then you will lose most profits because your GPU have to initialize each algo constantly.
You know algo switching needs time to reconnect.







There was DB error few hours ago and it caused some siacoin stats stuck.
Ethereum payout was stopped at that time period too.

Mining was not affected.

There will be no BCC credit if you exchange from BCC.
e.g.) If you've set BCC -> BTC, then BTC credit will appear at BTC pool.



Auto exchange needs time. All exchanges are done correctly.
You can see exchange results from bitcoin pool.






I upgraded few days ago. I believe it's all okay now.
Can you check from your side again?



Mining can be fluctuate.
No one can guarantee that especially if you use rental hash. They don't provide stable certain hashrate but goes up and down.

You need to mine with low speed for long period of time.
Also make sure that you do not leave the pool in the middle of mining. (This happens at nicehash frequently because of bid/ask change of hashpower)




How's it now?
And what numbers are shown at Graphs page?
Dashboard and workers page is not that accurate. It just estimates roughly.
Check Graphs page. It will show longer period average.






Manual job changes almost immediately. Less than 1~3 seconds.
Make sure that you are mining at 12xxx algo endpoint for Hub Worker Job changes.

I think you are mining at 17XXX ports which switch coin by profitability.
Just change 17 to 12 and test it again. It will work as intended.




What coin are you mining?
Maybe bitcoin?

Please do not mine bitcoin at miningpoolhub. No one found blocks yet. It means you would not get reward. Bitcoin blocks needs massive big hashrate to find even one block.









It was paused due to server upgrade. Most of you would not noticed but I upgraded server and switch each other seamlessly.

profitability info is updated like every 3 minutes at website.
API calls are cached. They are updated every 30 minutes.






No. But miningpoolhub doesn't need to close connection to send new extranonce to miners what nicehash like miners needs.
All switching is seamlessly done internally in pool.

The last block was found about 4 hours ago, have you been mining longer than that?
 

Hey,

I just switch a few dozen of CPU cores to XMR mining on this pool but I have an issue: despite I see my worker being online, and my hashrate on dashboard matching what I see on mining app, my credits stays at zero.

http://pix.toile-libre.org/upload/original/1503093403.png

Is there something wrong with the pool, or with my settings ?

Thanks!

My workers have disappeared, and my hasrate to 0? I see the message above, (siacoin) Please try again later

Nice, cant wait to hear your observations.

I have moved my rigs to this pool (ETH). Will check it.

Since nicehash already has a builtin auto switcher,
I think its better to add Hashrefinery or yiimp as next pool.

You have code your yiimp pool for mpm?