Antminer D3 Blissz firmware (10/12 v1.12 update) - page 87.

blissz

sr. member

Activity: 336

Merit: 258

Quote from: jakkuh on November 23, 2017, 04:54:29 PM

Where do the "hardware errors" show up?

Under miner status you have a column "HW" and you will see the count of each chain. Make sure to keep it low. 1 or 2 per minute per chain is the limit I would say. If you enable reboot on low hashrate detection you can try to see if it works for you as you have a few HW errors.

jakkuh

newbie

Activity: 1

Merit: 0

Where do the "hardware errors" show up?

blissz

sr. member

Activity: 336

Merit: 258

Quote from: Attie707 on November 23, 2017, 04:46:43 PM

My 4 D3 devices hash rate went down after the upgrade.

A reboot fixed it...

Thus REBOOT your D3 after the software upgrade!

Thanks for sharing in case someone else runs into this as well

Attie707

newbie

Activity: 7

Merit: 0

My 4 D3 devices hash rate went down after the upgrade.

A reboot fixed it...

Thus REBOOT your D3 after the software upgrade!

Ubersonic

newbie

Activity: 23

Merit: 0

Quote from: ruptan on November 23, 2017, 04:19:20 PM

Quote from: Duke33 on November 22, 2017, 01:30:25 PM

Hi guys, I have a law firm and I have already threatened BM, if we get together we can do a class action, if we decide all together my studio is available.

I think a lot of us are willing to do it. Class action seems like a very good idea.

Hate to break this to you but Bitmain is a Chinese company, China is know for many things one of them is being "not in the USA", you can't have a class action suit against a foreign company with no US base/presence because US courts have no jurisdiction in China, hell even if you fly over to China and start a regular suit the Chinese courts always side with Chinese companies when the plaintiffs are foreign (hence all the copyright/patent infringing knock offs there).

ruptan

sr. member

Activity: 491

Merit: 250

Quote from: Duke33 on November 22, 2017, 01:30:25 PM

Hi guys, I have a law firm and I have already threatened BM, if we get together we can do a class action, if we decide all together my studio is available.

I think a lot of us are willing to do it. Class action seems like a very good idea.

Ubersonic

newbie

Activity: 23

Merit: 0

Quote from: blissz on November 23, 2017, 03:44:34 PM

let me know if you have new features I should add (beside new algo's, this is still in continuous research)

I would really like the ability to set a timed schedule to switch between two hash/power/fan configs. That way I can have it tuned for silence when I'm home and when I'm at work it can be set it to switch to the best hash/watt setting.

Not sure if anyone else would be interested in this though.

dawidt

jr. member

Activity: 54

Merit: 10

Quote from: BartoszN1990 on November 23, 2017, 03:10:34 PM

Hash Rate:     Watts on wall:   Frequency:   ASIC Voltage:
1   15100 Mhs   800 Watts     431 Mhs     1
2   15850 Mhs   870 Watts     450 Mhs     3
3   17450 Mhs   965 Watts     500 Mhs     3
4   19350 Mhs   1145 Watts   550 Mhs     8-9-7
5   21150 Mhs   1510 Watts   600 Mhs      19-18-18
6   22100 Mhs   1659 Watts   625 Mhs     24-23-23

All setings tested and they are dont more op then Nonce#   0.005% wich is rly good .. all test after 1 h mining at random pool ....

Regards

............

analyzing your measures:
   mhs      W      mhs/w
1   15100   800      18,88
2   15850   870      18,22
3   17450   965      18,08
4   19350   1145      16,90
5   21150   1510      14,01
6   22100   1659      13,32

option 3 looks really optimal setting. I have to try it.

thanks

blissz

sr. member

Activity: 336

Merit: 258

I did reset and updated the poll. Please vote and let me know if you have new features I should add (beside new algo's, this is still in continuous research)

aa007

newbie

Activity: 1

Merit: 0

I was digging through the source code and it looks bad. The only way I see is to modify it somehow the pic.txt file.

If I understand the code correctly, the communication during mining with ASICs is done through DASH_write and DASH_read - just for getting work in and results out. The whole logic is in pic.txt program. There is even function to flash the program into the PIC - PIC1704_update_pic_app_program_new and then to invoke the new program itself - jump_from_loader_to_app_PIC16F1704_new. So I think if there is some chance to break in any part of the algo its hidden in pic.txt - but for that we would need somebody with good knowledge of reverse engineering.

We can also trigger instructions that are defined in https://github.com/bitmaintech/cgminer-dash/blob/master/driver-btm-DASH.h in about command between CPU and PIC16F1704 section. But nothing we can do to affect the algorithm itself in the driver. Or maybe there is something hidden

blissz

sr. member

Activity: 336

Merit: 258

Quote from: crackfoo on November 23, 2017, 02:59:20 PM

Does anyone elses fan on their nov batch run at diff speeds? Mine are both set @ 35%

Fan#    Fan1   Fan2
Speed (r/min)   2,130   2,670

While my sept batch are about the same:

Fan#    Fan1   Fan2
Speed (r/min)   2,760   2,790

Though... Nov batch is ~5c cooler in the chips....

Perhaps fan1 should always be running slower?

I replaced my fans, but I found out they cannot be controlled independently unfortunately... Because of the tube design I would say running them at the same speed is best, but your results tell a different story. Interesting stuff

blissz

sr. member

Activity: 336

Merit: 258

Quote from: ?? on ??

Quote from: blissz on November 23, 2017, 02:48:59 PM

Quote from: ?? on ??

Hi guys

Blissz Here are my new results average spees is 23.4 GH

After few tests managed to cool down the chips and most of HW errors

Fan 100% frequency 650 mhz voltage max

https://imgur.com/a/t6HeN

You are a record holder right now. What a hashrate. I hope you don't have to pay for the electricity? Wink

I am curious: did you measure the wattage?

I promise i will buy a watt meter tomorrow

Suggestion just for me and every one if they want
Can you ajust the max frequency to 1000 mhz is new version?

Yes I will increase the max frequency in the next version. I do have to test if the ASIC can run on this frequency of course. I will let you know

BartoszN1990

full member

Activity: 218

Merit: 100

https://deeponion.org

Hash Rate:     Watts on wall:   Frequency:   ASIC Voltage:
1   15100 Mhs   800 Watts     431 Mhs     1
2   15850 Mhs   870 Watts     450 Mhs     3
3   17450 Mhs   965 Watts     500 Mhs     3
4   19350 Mhs   1145 Watts   550 Mhs     8-9-7
5   21150 Mhs   1510 Watts   600 Mhs      19-18-18
6   22100 Mhs   1659 Watts   625 Mhs     24-23-23

All setings tested and they are dont more op then Nonce#   0.005% wich is rly good .. all test after 1 h mining at random pool ....

Regards

Quote

If anybo know how to do it:

1* How to pack folder:

Angstrom-antminer_m-eglibc-ipk-v2013.06-beaglebone.rootfs to keep all setings CPIO ? to take

Angstrom-antminer_m-eglibc-ipk-v2013.06-beaglebone.rootfs.cpio

2* How to pack fille:

Angstrom-antminer_m-eglibc-ipk-v2013.06-beaglebone.rootfs.cpio to keep all setings .bin.SD ? to take

initramfs.bin.SD

and last

3* How to pack fille:

am335x-boneblack-bitmainer.dtb
initramfs.bin.SD
runme.sh to keep all setings .tar.gz ? to take

Antminer-D3.tar.gz

Please send priv msg i have fiew concept setings with dificul auto change and adaptation to random pool + voltage. Regards !

crackfoo

legendary

Activity: 3556

Merit: 1126

Does anyone elses fan on their nov batch run at diff speeds? Mine are both set @ 35%

Fan#    Fan1   Fan2
Speed (r/min)   2,130   2,670

While my sept batch are about the same:

Fan#    Fan1   Fan2
Speed (r/min)   2,760   2,790

Though... Nov batch is ~5c cooler in the chips....

Perhaps fan1 should always be running slower?

blissz

sr. member

Activity: 336

Merit: 258

Quote from: ?? on ??

Hi guys

Blissz Here are my new results average spees is 23.4 GH

After few tests managed to cool down the chips and most of HW errors

Fan 100% frequency 650 mhz voltage max

https://imgur.com/a/t6HeN

You are a record holder right now. What a hashrate. I hope you don't have to pay for the electricity? Wink

I am curious: did you measure the wattage?

blissz

sr. member

Activity: 336

Merit: 258

Quote from: dalu1 on November 23, 2017, 12:37:41 PM

blissz, I just flashed my D3 s with your firmware. The noise is much quieter now. Otherwise, I would have to give up on those miners.

A Big THANKS

Glad to hear it works good for you! Cheesy

dottat

newbie

Activity: 48

Merit: 0

Guys can we please keep this thread on topic (custom firmware)??

Feel free to open another thread to discuss other topics so we have the option of subscribing to those topics

Thanks!

may142012

member

Activity: 301

Merit: 10

So, questions about immersion cooling, what kind of fish tank should i use? What kind of fluid should i use? Is it the 3M Novec one? Where do i buy it?

mcan

member

Activity: 70

Merit: 10

Quote from: blissz on November 23, 2017, 11:36:50 AM

Quote from: BartoszN1990 on November 23, 2017, 11:29:40 AM

Quote from: maqu on November 23, 2017, 10:18:17 AM

23/11 Blissz is working great:
Frequency = default 487
Voltage = 9
Hashrate = 17100 MH/z
Fan = Performance auton (4020rpm)
PCB temp = 55-57c
Chip temp = 71-71c
HW = 0

I'm wondering what makes temp rise above stock (65c) while under volting and stock clock? Hashrate is about the same with stock firmware.

Can u present watts from wall .. Voltage 9 is hight at 487

He is now on voltage 3

What do you think about XHASH function , is it doable changing algorithm ?

dalu1

member

Activity: 83

Merit: 10

Performing it is a better way of learning things

blissz, I just flashed my D3 s with your firmware. The noise is much quieter now. Otherwise, I would have to give up on those miners.

A Big THANKS

Topic: Antminer D3 Blissz firmware (10/12 v1.12 update) - page 87. (Read 125911 times)