ANTMINER S3+ Discussion and Support Thread - page 18.

notlist3d

legendary

Activity: 1456

Merit: 1000

Quote from: thebonenz on October 11, 2015, 10:05:24 PM

Does anyone have one lying around in Aus or close by?

I have a S3 controller laying around that I found. It needs flashed it lost power during a firmware upgrade. I just replaced it.

Just controller if anyone has a offer that is decent feel free to throw it over. Likely in a few day's I will list it in hardware.

thebonenz

member

Activity: 70

Merit: 10

Does anyone have one lying around in Aus or close by?

MikeMike

legendary

Activity: 2254

Merit: 1020

★ Ⓚ KORE TEAM Ⓚ ★

Quote from: RichBC on October 11, 2015, 02:02:44 PM

That's a Yes and Yes.

Rich

Perfect.

Thanks much Rich!

RichBC

hero member

Activity: 588

Merit: 500

That's a Yes and Yes.

Rich

MikeMike

legendary

Activity: 2254

Merit: 1020

★ Ⓚ KORE TEAM Ⓚ ★

Quote from: RichBC on October 11, 2015, 01:10:56 PM

There is wireless capability however you need to add a pigtail & antenna.

http://www.amazon.com/Wireless-WIFI-Antenna-with-Pigtail/dp/B005TX3GE0

Rich

Awesome!

I guess I could pull the pigtail from an old S1?
Then I only need an antenna right?

Could I pull an antenna from an old Wireless Router?

VirosaGITS

legendary

Activity: 1302

Merit: 1068

Quote from: RichBC on October 11, 2015, 01:47:06 PM

So long as your antenna is from a 2.4GHz device (most will be) then yes you just need the pigtail.

Rich

What would happen if i put a 2.2ghz antenna on it? Will it inhibit, or still help a little bit?

I remember seeing 2.2ghz and 2.4ghz antennas and i don't remember which one i bought :S

RichBC

hero member

Activity: 588

Merit: 500

So long as your antenna is from a 2.4GHz device (most will be) then yes you just need the pigtail.

Rich

VirosaGITS

legendary

Activity: 1302

Merit: 1068

Quote from: RichBC on October 11, 2015, 01:10:56 PM

There is wireless capability however you need to add a pigtail & antenna.

http://www.amazon.com/Wireless-WIFI-Antenna-with-Pigtail/dp/B005TX3GE0

Rich

That is great to know. So am i right to assume that all WIFI antenna are standards, so if i already have Antennas, i only need to buy these?;

http://www.ebay.ca/itm/2-X-U-FL-Mini-PCI-to-RP-SMA-Pigtail-Antenna-WiFi-Cable-/281487954155?hash=item4189fd50eb

RichBC

hero member

Activity: 588

Merit: 500

There is wireless capability however you need to add a pigtail & antenna.

http://www.amazon.com/Wireless-WIFI-Antenna-with-Pigtail/dp/B005TX3GE0

Rich

MikeMike

legendary

Activity: 2254

Merit: 1020

★ Ⓚ KORE TEAM Ⓚ ★

I see there is a wireless option in the LAN settings on my S3.
Can I connect directly to the Wireless network?
Heck I never knew the S3 had this capability!
Never hooked an S3 up through the WAN so could use a newbie help guide please.
Smiley
Or am I mistaken and there is no Wireless capability...

pinhead666

sr. member

Activity: 265

Merit: 250

I can see only one 8-pin connector and it's for MB, not PCI-E. Or did I miss something? According specs, you get enough power out of that PSU but you have to make your own cables or find someone to do it. 8 pin pci-e connector has 5 GND wires and 3 +12V wires, that MB connector has 4 GND and 4+12V wires (and they are connected different way than pci-e). So splitter won't work for you. You'll propably end up with smoke if you try that splitter.

Edit: I found pictures of similar PSU with two 8-pin connectors but still they are 8-pin EPS12V.

Edit 2: Found an adapter: http://www.moddiy.com/products/Bitcoin-Mining-CPU-8pin-TO-2-PCI%252dE-6%252b2pin-Splitter-Cable.html

vanga83

newbie

Activity: 2

Merit: 0

Quote from: MyRig on October 10, 2015, 04:41:31 PM

PSU wattage may be, however, please make sure there are 4 PCI-E connectors on the PSU or have an ability to make the necessary modifications to have safe 4 PCI-E connectors.

Quote from: vanga83 on October 10, 2015, 04:24:12 PM

I'm new to this and recently picked up an S3+. From what I've been reading, the server power supply from here http://www.ebay.com/itm/251982322928?_trksid=p2055119.m1438.l2649&ssPageName=STRK%3AMEBIDX%3AIT looks sufficient to power one Antminer. Just wanted to double check with you guys if it would be a good choice. Thanks.

Cool. Thank you. This power supply has two 8-pin 12v connectors and I was thinking of getting a couple of 8-pin to 6-pin splitters to have a total of four usable 6-pin connectors to plug into to the Antiminer.

MyRig

donator

Activity: 792

Merit: 510

[email protected]

PSU wattage may be, however, please make sure there are 4 PCI-E connectors on the PSU or have an ability to make the necessary modifications to have safe 4 PCI-E connectors.

Quote from: vanga83 on October 10, 2015, 04:24:12 PM

I'm new to this and recently picked up an S3+. From what I've been reading, the server power supply from here http://www.ebay.com/itm/251982322928?_trksid=p2055119.m1438.l2649&ssPageName=STRK%3AMEBIDX%3AIT looks sufficient to power one Antminer. Just wanted to double check with you guys if it would be a good choice. Thanks.

vanga83

newbie

Activity: 2

Merit: 0

I'm new to this and recently picked up an S3+. From what I've been reading, the server power supply from here http://www.ebay.com/itm/251982322928?_trksid=p2055119.m1438.l2649&ssPageName=STRK%3AMEBIDX%3AIT looks sufficient to power one Antminer. Just wanted to double check with you guys if it would be a good choice. Thanks.

Jake-R

full member

Activity: 142

Merit: 100

I just got one of these and while it is quiet, it is still somewhat loud when trying to watch television. I want to drop the frequency down to 100M during the evening when I am in the room, then put it back to 225M (the default frequency). Basically, underclock when I am in the room and put to the normal speed when I go to bed/work.

Is there any danger of damaging the memory/storage with frequent writes to it? I don't imagine there is a hard drive inside the unit, so it must be writing the setting to some other form of non-volatile storage (with potentially limited writes).

Also, is it possible to automate this and have it follow a schedule?

aarons6

legendary

Activity: 1736

Merit: 1006

Quote from: Sweminer777 on September 16, 2015, 03:14:44 PM

How is the hardware Error on the machines average?

490 HW
0.0039 HW%

i think is abit high , been running 37hours non stop right now .

that isnt too bad.. my worse on at almost 3 days up is at 1600~ errors hw% .0059
thats at stock speed..

the best one i have is same uptime 95 errors hw% 0.0003 this one is OC to 231

RichBC

hero member

Activity: 588

Merit: 500

Quote from: charles2k on September 16, 2015, 04:08:30 PM

Quote from: RichBC on September 16, 2015, 09:56:33 AM

If you want to save money but still get a quality PSU then go for a second hand Hot Swap Server PSU. Many to choose from on ebay, here is a good example.

http://www.ebay.co.uk/itm/P081-HP-DL380-ML380-G5-POWER-SUPPLY-DPS-800GB-A-379123-001-403781-001-1000W-PSU-/351399031780?hash=item51d103b3e4

This is an HP DPS-800GB which will do 1000W with 82 Amps on 12V all Day long. Look on the RC forums for detail on how to connect up and enable it.

Rich

This HP server PSU has efficiency only 80+ bronze...

This was just an example of what you can get for £15 as opposed to a cheap ATX PSU. If you can suggest something better for the money please go ahead? Either way "only 80+ bronze" is a bit academic if the OP is going to using an S1.

Rich

charles2k

sr. member

Activity: 326

Merit: 250

Quote from: RichBC on September 16, 2015, 09:56:33 AM

If you want to save money but still get a quality PSU then go for a second hand Hot Swap Server PSU. Many to choose from on ebay, here is a good example.

http://www.ebay.co.uk/itm/P081-HP-DL380-ML380-G5-POWER-SUPPLY-DPS-800GB-A-379123-001-403781-001-1000W-PSU-/351399031780?hash=item51d103b3e4

This is an HP DPS-800GB which will do 1000W with 82 Amps on 12V all Day long. Look on the RC forums for detail on how to connect up and enable it.

Rich

This HP server PSU has efficiency only 80+ bronze...

Sweminer777

hero member

Activity: 754

Merit: 500

1xBit the largest casino

How is the hardware Error on the machines average?

490 HW
0.0039 HW%

i think is abit high , been running 37hours non stop right now .

pinhead666

sr. member

Activity: 265

Merit: 250

Quote from: adaseb on September 16, 2015, 12:21:00 PM

Quote from: Stratobitz on September 15, 2015, 01:36:54 PM

Without adding an antennae whats the wifi range on an S3+. Just curious. Thanks!

Strato

Take apart an old laptop which had wifi and use those antennas. Each laptop had 2.

Good advise. I used those with S1,when I needed wider range.Cheap and very effective way.

Topic: ANTMINER S3+ Discussion and Support Thread - page 18. (Read 710231 times)