ANTMINER S3+ Discussion and Support Thread - page 368.

oskuro

sr. member

Activity: 294

Merit: 251

Quote from: Lowell904 on July 27, 2014, 03:43:49 PM

Quote from: oskuro on July 27, 2014, 03:41:11 PM

The huge amount of discards and so low accepted then thats because they are the opposite? discards = accepted and accepted = discards?

It does not seem that way. Some of us got those discards down via a setting mod, and the accepted shares stayed about the same.

Mmmm then whats the problem?? with S1 those values were always good. And in my pool im not having problems so.... those discards must be wrong Huh

And i dont think im the only one having this issue

bitcoinbelieve

sr. member

Activity: 658

Merit: 250

Quote from: crazyearner on July 27, 2014, 03:49:29 PM

After reading your comments on last post then might want to try this as a cheap option and work around.

http://www.overclockers.co.uk/showproduct.php?prodid=WC-209-XS&adword=google/pla/unoptimized&gclid=CMrlqsyu5r8CFU7MtAodFXsASw

buy one for each unit or so least gives you an idea of what the temps are. Also looking at the unit could easily install these to units

Hope this might help you with a optional solution.

thanks for your help

crazyearner

legendary

Activity: 1820

Merit: 1001

Quote from: bitcoinbelieve on July 27, 2014, 03:42:15 PM

Here is what I'm talking about

After reading your comments on last post then might want to try this as a cheap option and work around.

http://www.overclockers.co.uk/showproduct.php?prodid=WC-209-XS&adword=google/pla/unoptimized&gclid=CMrlqsyu5r8CFU7MtAodFXsASw

buy one for each unit or so least gives you an idea of what the temps are. Also looking at the unit could easily install these to units

Hope this might help you with a optional solution.

bitcoinbelieve

sr. member

Activity: 658

Merit: 250

Quote from: crazyearner on July 27, 2014, 03:18:55 PM

is part of the module un plug the fan and place in the other one ie reverse it and see if the temperature shows on the other controller instead. if this does not work then it will be controller and am not sure where the actual temp sensor is no doubt some tiny thing sitting under the heat sync somewhere but cant actually see. Avalon had a wire sensor you can replace and I did exactly that on my avalon.

Antminer on the other hand think its part of the unit built into it. only option try flipping the fan to the other end and flip around see if that sensor works on that one if it don't then it. However having said that this is the S3 I would need to see it in parts to see where the sensor is on it maybe someone already had one in bits and broke down. if looking at one inside with the tiny heat plates then could be under one of them or its built in.

If built in on a tiny resistor sort of thing then you only have 2 options 1 is flashing firmware seeing if that will work or 2 living with it and contacting bitmain about it for poss RMA or some sort of guidance on where location of it is and seeing if damaged.

I have done flashing firmware (twice), unplugged, plugged everything and still no success.

Lowell904

member

Activity: 119

Merit: 10

Quote from: oskuro on July 27, 2014, 03:41:11 PM

The huge amount of discards and so low accepted then thats because they are the opposite? discards = accepted and accepted = discards?

It does not seem that way. Some of us got those discards down via a setting mod, and the accepted shares stayed about the same.

bitcoinbelieve

sr. member

Activity: 658

Merit: 250

Here is what I'm talking about

oskuro

sr. member

Activity: 294

Merit: 251

The huge amount of discards and so low accepted then thats because they are the opposite? discards = accepted and accepted = discards?

bitcoinbelieve

sr. member

Activity: 658

Merit: 250

Quote from: hobbymd on July 27, 2014, 03:15:22 PM

I also had*thought* a faulty temp sensor on one of the s2 blades but didn't care since it was hashing fine and temps were ok and it would have cost me more to rma it so I lived with it. until this weekend when I cleaned the blades for the first time and removed excess paste on both sides of each blade.

when I turned it back on noticed I had temp reading on that same blade that had faulty sensor before Wink

so maybe in your case if you have excess paste then it might be the cause Wink

I think I will do that next

crazyearner

legendary

Activity: 1820

Merit: 1001

Quote from: bitcoinbelieve on July 27, 2014, 02:59:48 PM

Quote from: crazyearner on July 27, 2014, 02:38:13 PM

Quote from: bitcoinbelieve on July 27, 2014, 02:03:15 PM

One of my S3 temperature shows as 0 (for both chain 1, 2). How do I resolve this?

I tried to restart, reboot and nothing helped.

Have a look inside the ant miner see if the sensor is actually connected to the board or try removing and re applying it. Make sure unit is turned off when doing this. If it is then you could try firmware update flash with image then reset to see if it comes on if it don't then this looks more of a faulty sensor if none of the above resolves the problem then looks like possible rma.

what does it look like?

is part of the module un plug the fan and place in the other one ie reverse it and see if the temperature shows on the other controller instead. if this does not work then it will be controller and am not sure where the actual temp sensor is no doubt some tiny thing sitting under the heat sync somewhere but cant actually see. Avalon had a wire sensor you can replace and I did exactly that on my avalon.

Antminer on the other hand think its part of the unit built into it. only option try flipping the fan to the other end and flip around see if that sensor works on that one if it don't then it. However having said that this is the S3 I would need to see it in parts to see where the sensor is on it maybe someone already had one in bits and broke down. if looking at one inside with the tiny heat plates then could be under one of them or its built in.

If built in on a tiny resistor sort of thing then you only have 2 options 1 is flashing firmware seeing if that will work or 2 living with it and contacting bitmain about it for poss RMA or some sort of guidance on where location of it is and seeing if damaged.

hobbymd

sr. member

Activity: 259

Merit: 250

Quote from: bitcoinbelieve on July 27, 2014, 02:55:24 PM

Quote from: windpath on July 27, 2014, 02:39:13 PM

Quote from: sjc1490 on July 27, 2014, 02:32:24 PM

Quote from: bitcoinbelieve on July 27, 2014, 02:28:45 PM

Quote from: sjc1490 on July 27, 2014, 02:24:05 PM

Quote from: bitcoinbelieve on July 27, 2014, 02:03:15 PM

One of my S3 temperature shows as 0 (for both chain 1, 2). How do I resolve this?

I tried to restart, reboot and nothing helped.

You have confirmed that is it mining and submitting?

Yes

One of my S2's has a bad sensor on one card always has reported 0 and it is just bad. This is probably going to be a rma issue for bitmain as I don't know of a software or tweak fix for it. Are the fans functioning correctly, changing speeds as needed?

RMA for a faulty temp sensor is going to cost you more then its worth...

If your concerned one of the fans is running to slow because of the sensor reporting 0 just cut the blue wire (yes, cut the blue wire) on the fan and it will run full speed.

The fans are working as it should

I also had*thought* a faulty temp sensor on one of the s2 blades but didn't care since it was hashing fine and temps were ok and it would have cost me more to rma it so I lived with it. until this weekend when I cleaned the blades for the first time and removed excess paste on both sides of each blade.

when I turned it back on noticed I had temp reading on that same blade that had faulty sensor before Wink

so maybe in your case if you have excess paste then it might be the cause Wink

bitcoinbelieve

sr. member

Activity: 658

Merit: 250

Quote from: crazyearner on July 27, 2014, 02:38:13 PM

Quote from: bitcoinbelieve on July 27, 2014, 02:03:15 PM

One of my S3 temperature shows as 0 (for both chain 1, 2). How do I resolve this?

I tried to restart, reboot and nothing helped.

Have a look inside the ant miner see if the sensor is actually connected to the board or try removing and re applying it. Make sure unit is turned off when doing this. If it is then you could try firmware update flash with image then reset to see if it comes on if it don't then this looks more of a faulty sensor if none of the above resolves the problem then looks like possible rma.

what does it look like?

bitcoinbelieve

sr. member

Activity: 658

Merit: 250

Quote from: windpath on July 27, 2014, 02:39:13 PM

Quote from: sjc1490 on July 27, 2014, 02:32:24 PM

Quote from: bitcoinbelieve on July 27, 2014, 02:28:45 PM

Quote from: sjc1490 on July 27, 2014, 02:24:05 PM

Quote from: bitcoinbelieve on July 27, 2014, 02:03:15 PM

One of my S3 temperature shows as 0 (for both chain 1, 2). How do I resolve this?

I tried to restart, reboot and nothing helped.

You have confirmed that is it mining and submitting?

Yes

One of my S2's has a bad sensor on one card always has reported 0 and it is just bad. This is probably going to be a rma issue for bitmain as I don't know of a software or tweak fix for it. Are the fans functioning correctly, changing speeds as needed?

RMA for a faulty temp sensor is going to cost you more then its worth...

If your concerned one of the fans is running to slow because of the sensor reporting 0 just cut the blue wire (yes, cut the blue wire) on the fan and it will run full speed.

The fans are working as it should

Duce

full member

Activity: 175

Merit: 100

Quote from: faetos on July 27, 2014, 01:45:02 PM

Quote from: Xian01 on July 27, 2014, 11:37:20 AM

FWIW, After ~10 hours running with --queue 32, slightly overclocked to 225, share difficulty set to 256.

Does not seem to have affected hashing at all, but noticeable CPU load decrease.

Quote from: Xian01 on July 27, 2014, 01:05:42 AM

Quote from: -ck on July 27, 2014, 12:49:16 AM

Quote from: Lowell904 on July 27, 2014, 12:44:49 AM

Please, what would you suggest we set the queue, scan time and expiry to?

Again, do not touch scan time and expiry.
Giving you generic advice regarding the queue setting is difficult because this is not my driver...I'd be surprised if it really needs to be that high though, and on a low powered system there is rarely anything to gain from anything even in the hundreds, let alone thousands.

Thanks for this. Going to run one of my units with --queue 32 overnight and see how the stats look when I wake up.

I tried it at 64 and got a high discard rate. I'll try it with 32 as you have and see if that will be my sweet spot. I removed the scan time and expiry as ck suggested.

I am glad "CK" provided his input as I too removed scan and expiry from the settings for pool operation but have put them back in for P2P testing as "CK" said was worth testing. BTW apparently "BestShare" is always reported from P2P but not all major pools. Don't know if you noticed that or not so I figured I would throw that out there.

sjc1490

hero member

Activity: 546

Merit: 500

Quote from: bitcoinbelieve on July 27, 2014, 02:37:38 PM

Quote from: sjc1490 on July 27, 2014, 02:32:24 PM

Quote from: bitcoinbelieve on July 27, 2014, 02:28:45 PM

Quote from: sjc1490 on July 27, 2014, 02:24:05 PM

Quote from: bitcoinbelieve on July 27, 2014, 02:03:15 PM

One of my S3 temperature shows as 0 (for both chain 1, 2). How do I resolve this?

I tried to restart, reboot and nothing helped.

You have confirmed that is it mining and submitting?

Yes

One of my S2's has a bad sensor on one card always has reported 0 and it is just bad. This is probably going to be a rma issue for bitmain as I don't know of a software or tweak fix for it. Are the fans functioning correctly, changing speeds as needed?

Everything is working order except the temp display

If everything else is working fine I would live with it, that is what I have done.

windpath

legendary

Activity: 1258

Merit: 1027

Quote from: sjc1490 on July 27, 2014, 02:32:24 PM

Quote from: bitcoinbelieve on July 27, 2014, 02:28:45 PM

Quote from: sjc1490 on July 27, 2014, 02:24:05 PM

Quote from: bitcoinbelieve on July 27, 2014, 02:03:15 PM

One of my S3 temperature shows as 0 (for both chain 1, 2). How do I resolve this?

I tried to restart, reboot and nothing helped.

You have confirmed that is it mining and submitting?

Yes

One of my S2's has a bad sensor on one card always has reported 0 and it is just bad. This is probably going to be a rma issue for bitmain as I don't know of a software or tweak fix for it. Are the fans functioning correctly, changing speeds as needed?

RMA for a faulty temp sensor is going to cost you more then its worth...

If your concerned one of the fans is running to slow because of the sensor reporting 0 just cut the blue wire (yes, cut the blue wire) on the fan and it will run full speed.

crazyearner

legendary

Activity: 1820

Merit: 1001

Quote from: bitcoinbelieve on July 27, 2014, 02:03:15 PM

One of my S3 temperature shows as 0 (for both chain 1, 2). How do I resolve this?

I tried to restart, reboot and nothing helped.

Have a look inside the ant miner see if the sensor is actually connected to the board or try removing and re applying it. Make sure unit is turned off when doing this. If it is then you could try firmware update flash with image then reset to see if it comes on if it don't then this looks more of a faulty sensor if none of the above resolves the problem then looks like possible rma.

Lowell904

member

Activity: 119

Merit: 10

Quote from: sjc1490 on July 27, 2014, 01:54:44 PM

I have been playing around with a variety of different numbers also best overall performance (load, HWE, Discards, and stales) I have gotten is setting all 3 settings to 1 and that is what I am staying with.

Thanks for posting. I'll be playing around a bit today as well.

Are you using 2 or 4 cables? I would like to try to go to 225 after I get some heat sinks for the DC/DCs but I will only have 2 cables available.

bitcoinbelieve

sr. member

Activity: 658

Merit: 250

Quote from: sjc1490 on July 27, 2014, 02:32:24 PM

Quote from: bitcoinbelieve on July 27, 2014, 02:28:45 PM

Quote from: sjc1490 on July 27, 2014, 02:24:05 PM

Quote from: bitcoinbelieve on July 27, 2014, 02:03:15 PM

One of my S3 temperature shows as 0 (for both chain 1, 2). How do I resolve this?

I tried to restart, reboot and nothing helped.

You have confirmed that is it mining and submitting?

Yes

One of my S2's has a bad sensor on one card always has reported 0 and it is just bad. This is probably going to be a rma issue for bitmain as I don't know of a software or tweak fix for it. Are the fans functioning correctly, changing speeds as needed?

Everything is working order except the temp display

Lowell904

member

Activity: 119

Merit: 10

Quote from: crazyearner on July 27, 2014, 12:05:13 PM

Quote from: Xian01 on July 27, 2014, 11:56:58 AM

Quote from: crazyearner on July 27, 2014, 11:54:21 AM

Has their been any news on the S1 upgrade modules to upgrade with the S3 modules to use

No news yet. Curious myself. Have 9 S1's collecting dust I would like to upgrade if possible.

Mine are going to be collecting dust at the end of this month when they get turned off however going into a partnership for mining as opted to pay me for energy costs so going to see how it works outs. other than that if it fails then ill probs end up holding them until theirs news of the upgrade modules and continue to trade on markets.

I'll be under-clocking and under-volting my S1 in a month or so as it will make it more efficient and thus, profitable for a little longer.

sjc1490

hero member

Activity: 546

Merit: 500

Quote from: bitcoinbelieve on July 27, 2014, 02:28:45 PM

Quote from: sjc1490 on July 27, 2014, 02:24:05 PM

Quote from: bitcoinbelieve on July 27, 2014, 02:03:15 PM

One of my S3 temperature shows as 0 (for both chain 1, 2). How do I resolve this?

I tried to restart, reboot and nothing helped.

You have confirmed that is it mining and submitting?

Yes

One of my S2's has a bad sensor on one card always has reported 0 and it is just bad. This is probably going to be a rma issue for bitmain as I don't know of a software or tweak fix for it. Are the fans functioning correctly, changing speeds as needed?

Topic: ANTMINER S3+ Discussion and Support Thread - page 368. (Read 710164 times)