Any word on the refunds? It's been over 10 days! 
Did you recheck your Bitmain acct. I had to reverify the address to receive at.Did you get your refund yet?
Topic: ANTMINER S3+ Discussion and Support Thread - page 379. (Read 710164 times)
Did you get your refund yet?
10 hours later... and FINALLY WORKING!
it was just the dns. farrrrrrrrrrrrrr out. it literally took 10 seconds and now everything working.
thanks every1 i hope this will benefit others in the future.
it was just the dns. farrrrrrrrrrrrrr out. it literally took 10 seconds and now everything working.
thanks every1 i hope this will benefit others in the future.
what dns worked for you? 8.8.8.8 or some other one?
4.2.2.2 worked for me but i do get alot rejects and discarded. is this normal?
http://s30.postimg.org/ak05ldb69/antminer.jpg
Any word on the refunds? It's been over 10 days!
Did you recheck your Bitmain acct. I had to reverify the address to receive at.
Any word on the refunds? It's been over 10 days!
so far tried 5 different pools NONE of them I can connect to. I do factory reset and it just starts mining straight away someone please help
Are you changing anything in the network settings? Is your Antminer in the IP range covered by your router?In the pool configuration you don't need to enter 'http://...' only 'stratum.bitcoin.cz:3333' (example if you use Slush). Make sure that you don't enter any extra spaces and that all of your credentials (Pool worker and password) are correct.
Cheers
And make sure you set a DNS too. That was my mistake. I have mine on 8.8.8.8 and 4.2.2.2.
no but what DOESNT make sense is everything works fine once reset. its only when I input my own pool (uk1.ghash.io:3333) etc it dont work. i have tried btcguild ozcoin f2pool and few others. what am i missing?
when you have changed the settings make sure you use the "save and apply" button (for each page you change)
when you are finished with changing settings then do a "system" "reboot" "perform reboot"
some of mine need this reboot sequence, some of them work straight away.
10 hours later... and FINALLY WORKING!
it was just the dns. farrrrrrrrrrrrrr out. it literally took 10 seconds and now everything working.
thanks every1 i hope this will benefit others in the future.
it was just the dns. farrrrrrrrrrrrrr out. it literally took 10 seconds and now everything working.
thanks every1 i hope this will benefit others in the future.
what dns worked for you? 8.8.8.8 or some other one?
10 hours later... and FINALLY WORKING!
it was just the dns. farrrrrrrrrrrrrr out. it literally took 10 seconds and now everything working.
thanks every1 i hope this will benefit others in the future.
it was just the dns. farrrrrrrrrrrrrr out. it literally took 10 seconds and now everything working.
thanks every1 i hope this will benefit others in the future.
so far tried 5 different pools NONE of them I can connect to. I do factory reset and it just starts mining straight away someone please help
Are you changing anything in the network settings? Is your Antminer in the IP range covered by your router?In the pool configuration you don't need to enter 'http://...' only 'stratum.bitcoin.cz:3333' (example if you use Slush). Make sure that you don't enter any extra spaces and that all of your credentials (Pool worker and password) are correct.
Cheers
And make sure you set a DNS too. That was my mistake. I have mine on 8.8.8.8 and 4.2.2.2.
no but what DOESNT make sense is everything works fine once reset. its only when I input my own pool (uk1.ghash.io:3333) etc it dont work. i have tried btcguild ozcoin f2pool and few others. what am i missing?
okay look at my screenshot above with my pool setting it is for btcguild copy it into your miner and see if it mines for me. if it mines for me and not for your btcguild account I would be shocked. obvious if it does that you must have wrong info on your btcguild acct. also if it does that do not keep mining for me.
make sure you have a password set 123 works.. also play around with your dns settings 8.8.8.8 does not work well for me i use my routers address and it works
so far tried 5 different pools NONE of them I can connect to. I do factory reset and it just starts mining straight away someone please help
Are you changing anything in the network settings? Is your Antminer in the IP range covered by your router?In the pool configuration you don't need to enter 'http://...' only 'stratum.bitcoin.cz:3333' (example if you use Slush). Make sure that you don't enter any extra spaces and that all of your credentials (Pool worker and password) are correct.
Cheers
And make sure you set a DNS too. That was my mistake. I have mine on 8.8.8.8 and 4.2.2.2.
no but what DOESNT make sense is everything works fine once reset. its only when I input my own pool (uk1.ghash.io:3333) etc it dont work. i have tried btcguild ozcoin f2pool and few others. what am i missing?
I had exactly the same as you. I`d reset my Ants and they would hash fine. Where it says "use custom DNS server" try putting a new DNS like 8.8.8.8. It worked for me. Give it a pop.
so far tried 5 different pools NONE of them I can connect to. I do factory reset and it just starts mining straight away someone please help
Are you changing anything in the network settings? Is your Antminer in the IP range covered by your router?In the pool configuration you don't need to enter 'http://...' only 'stratum.bitcoin.cz:3333' (example if you use Slush). Make sure that you don't enter any extra spaces and that all of your credentials (Pool worker and password) are correct.
Cheers
And make sure you set a DNS too. That was my mistake. I have mine on 8.8.8.8 and 4.2.2.2.
no but what DOESNT make sense is everything works fine once reset. its only when I input my own pool (uk1.ghash.io:3333) etc it dont work. i have tried btcguild ozcoin f2pool and few others. what am i missing?
ok just to narrow it down:
i am running this off my home PC's power supply. it has 2 6p connectors coming from my silverstone 1200w. my home pc is fairly basic nothing over the top so its got plenty of juice. (is a dedicated psu must?)
AND
on my router the router lights up orange rather than green but i can still log into s3 and change settings. and as i mentioned it will mine once it is reset all on original settings.
i have been on this 10 hours straight now and i feel like throwing the miner at the wall.
also i have somewhat previous experience in mining - like 8 rigs at a time etc. so i know how workers, pools, basically work.
i am running this off my home PC's power supply. it has 2 6p connectors coming from my silverstone 1200w. my home pc is fairly basic nothing over the top so its got plenty of juice. (is a dedicated psu must?)
AND
on my router the router lights up orange rather than green but i can still log into s3 and change settings. and as i mentioned it will mine once it is reset all on original settings.
i have been on this 10 hours straight now and i feel like throwing the miner at the wall.
also i have somewhat previous experience in mining - like 8 rigs at a time etc. so i know how workers, pools, basically work.
without lots of screen shots can't tell what is wrong.
here are 2 working s-3's what does this page look like for you? notice both work even with wrong wireless settings since I am using cat5 hookup
Ipv4 broadcast 192.168.0.255 would be good since the miners are at 0.246 and 0.245 192.168.1.255 is wrong
here are some pool settings
notice you must have a password
so far tried 5 different pools NONE of them I can connect to. I do factory reset and it just starts mining straight away someone please help
Are you changing anything in the network settings? Is your Antminer in the IP range covered by your router?In the pool configuration you don't need to enter 'http://...' only 'stratum.bitcoin.cz:3333' (example if you use Slush). Make sure that you don't enter any extra spaces and that all of your credentials (Pool worker and password) are correct.
Cheers
And make sure you set a DNS too. That was my mistake. I have mine on 8.8.8.8 and 4.2.2.2.
ok just to narrow it down:
i am running this off my home PC's power supply. it has 2 6p connectors coming from my silverstone 1200w. my home pc is fairly basic nothing over the top so its got plenty of juice. (is a dedicated psu must?)
AND
on my router the router lights up orange rather than green but i can still log into s3 and change settings. and as i mentioned it will mine once it is reset all on original settings.
i have been on this 10 hours straight now and i feel like throwing the miner at the wall.
also i have somewhat previous experience in mining - like 8 rigs at a time etc. so i know how workers, pools, basically work.
i am running this off my home PC's power supply. it has 2 6p connectors coming from my silverstone 1200w. my home pc is fairly basic nothing over the top so its got plenty of juice. (is a dedicated psu must?)
AND
on my router the router lights up orange rather than green but i can still log into s3 and change settings. and as i mentioned it will mine once it is reset all on original settings.
i have been on this 10 hours straight now and i feel like throwing the miner at the wall.
also i have somewhat previous experience in mining - like 8 rigs at a time etc. so i know how workers, pools, basically work.
so far tried 5 different pools NONE of them I can connect to. I do factory reset and it just starts mining straight away someone please help
Are you changing anything in the network settings? Is your Antminer in the IP range covered by your router?In the pool configuration you don't need to enter 'http://...' only 'stratum.bitcoin.cz:3333' (example if you use Slush). Make sure that you don't enter any extra spaces and that all of your credentials (Pool worker and password) are correct.
Cheers
i dont use slush just the address. made sure NO extra spaces.
what do you mean by a IP range covered by router.
my gateway ip is:
192.168.1.1
pc ip is:
192.168.1.11
s3 ip is:
192.168.1.99
so far tried 5 different pools NONE of them I can connect to. I do factory reset and it just starts mining straight away someone please help
Are you changing anything in the network settings? Is your Antminer in the IP range covered by your router?In the pool configuration you don't need to enter 'http://...' only 'stratum.bitcoin.cz:3333' (example if you use Slush). Make sure that you don't enter any extra spaces and that all of your credentials (Pool worker and password) are correct.
Cheers
can someone share what is a single S3 on a decent PSU pulling from the wall in terms of power ?
cheers
cheers
328 watts set on freq 212.5 hashing at 433gh. psu = seasonic plat 1000 watt
337 watts with an evga 1300 watt gold same freq 212.5
so far tried 5 different pools NONE of them I can connect to. I do factory reset and it just starts mining straight away someone please help
Chek Lap Kok, Hong Kong 07/25/2014 4:35 P.M. We've missed the scheduled transfer time. This may cause a delay.
Shenzhen, China 07/25/2014 10:40 A.M. Departure Scan
07/25/2014 1:56 A.M. Arrival Scan
07/25/2014 1:36 A.M. Departure Scan
Shenzhen, China 07/24/2014 11:15 A.M. Origin Scan
China 07/21/2014 3:50 A.M. Order Processed: Ready for UPS
Scheduled Delivery:
Monday, 07/28/2014, By End of Day <<<<<----- Yeah fucking right
Shenzhen, China 07/25/2014 10:40 A.M. Departure Scan
07/25/2014 1:56 A.M. Arrival Scan
07/25/2014 1:36 A.M. Departure Scan
Shenzhen, China 07/24/2014 11:15 A.M. Origin Scan
China 07/21/2014 3:50 A.M. Order Processed: Ready for UPS
Scheduled Delivery:
Monday, 07/28/2014, By End of Day <<<<<----- Yeah fucking right
hey all. no matter i try i cant get my s3 to work. I have a feeling its borked!
when i reset it start hashing. whenever i change over to my pool it wont work. It has done my head it. Please help/advice any help would be fantastic
when i reset it start hashing. whenever i change over to my pool it wont work. It has done my head it. Please help/advice any help would be fantastic
If i want to use these small fans to lower temperature:
https://www.leroymerlin.es/fp/14453873/ventilador-fe-10c
and because i see its so cheap to have them all day running... where will you place them? i mean, these S3 are inside a box, so i will have maybe to put those fans in the rear part taking hot air out, and maybe in front also to blow more fresh air inside the front vent that blows air into the S3?
https://www.leroymerlin.es/fp/14453873/ventilador-fe-10c
and because i see its so cheap to have them all day running... where will you place them? i mean, these S3 are inside a box, so i will have maybe to put those fans in the rear part taking hot air out, and maybe in front also to blow more fresh air inside the front vent that blows air into the S3?
Jump to: