Bitcoin Forum>Bitcoin>Mining>Mining software (miners)
Pages:
Author

Topic: Antminer S9 Volt Rocket Ship firmware mod! ~Time to Max Out Your Bitmain PSU~ - page 19. (Read 32694 times)

piscess16
newbie
Activity: 11
Merit: 0
Re: Antminer S9 Volt Rocket Ship firmware mod! ~Time to Max Out Your Bitmain PSU~
July 31, 2018, 02:14:45 AM
#116
Quote from: taserz on July 30, 2018, 11:12:11 PM
It was made for a user that their bmminer for t9+ was flashed with S9 firmware. But yes it should work with the T9+ since it only has the few changes as the s9 but I compiled it for the T9+ definitions.

oh, understand.

and want to ask the T9+ can overclock?

and how to setup S9 with original hashrate integrate a dev fee
taserz
sr. member
Activity: 800
Merit: 294
Created AutoTune to saved the planet! ~USA
Re: Antminer S9 Volt Rocket Ship firmware mod! ~Time to Max Out Your Bitmain PSU~
July 30, 2018, 11:12:11 PM
#115
Quote from: piscess16 on July 30, 2018, 10:53:19 PM
bmminer880_T9+

this is support T9+ ?

It was made for a user that their bmminer for t9+ was flashed with S9 firmware. But yes it should work with the T9+ since it only has the few changes as the s9 but I compiled it for the T9+ definitions.
piscess16
newbie
Activity: 11
Merit: 0
Re: Antminer S9 Volt Rocket Ship firmware mod! ~Time to Max Out Your Bitmain PSU~
July 30, 2018, 10:53:19 PM
#114
bmminer880_T9+

this is support T9+ ?
taserz
sr. member
Activity: 800
Merit: 294
Created AutoTune to saved the planet! ~USA
Re: Antminer S9 Volt Rocket Ship firmware mod! ~Time to Max Out Your Bitmain PSU~
July 30, 2018, 10:37:25 PM
#113
Quote from: somename on July 30, 2018, 03:02:54 PM
Hi, thank you very much for that firmware. I did some testing with 880mV version and measured the energy consuption at the wall using energy meter. Not sure if it is super accurate, but its just for comparsion. I'm running all miners in oil, but PSU (original bitmain 1600W) are outsite and ambient temp is quite high (35C/95F during day now), therefore I'm not going to run those PSUs at 120%.

S9i (running its original autotune FW)
stock 14TH@1450W
- 675MHz 14.5TH@1530W
- 725MHz 15.6TH@1650W
- 750HHz 16.1TH@1710W - I will be running this setting, HW errors in single digits per hour
- 775MHz 16.7TH@1770W

S9 (original autotune FW, 03/2018 batch I think)
stock 13,8TH@1480W (900mV,900mV,910mV)
- 700MHz 15TH@1580W
- 725MHz 15.6TH@1650W
- 750MHz 16.1TH@1700W

Interesting thing for me is, that temperature on those S9i increased only about 1-degrees, but on S9 it is now +20C (61->81). Do you have any idea why? Does it have something to do with "TempTypeID=1a middle offset=-51"? Maybe those older boards should have different offset?

Also, will you be so kind and compile 870mV FW and put it on github? I would love to try lower voltage and higher clock speed, as I'm oil-cooling it I have no problems with overheating.

Yes I will do it later tonight or in the morning.

I noticed your s9i and s9 run the same wattage at 72MHz What is funny though I run my S9i 14th unit at 800mhz on a 1600w psu and it runs just fine without tripping the psu.
taserz
sr. member
Activity: 800
Merit: 294
Created AutoTune to saved the planet! ~USA
Re: Antminer S9 Volt Rocket Ship firmware mod! ~Time to Max Out Your Bitmain PSU~
July 30, 2018, 10:22:19 PM
#112
Quote from: zeus_pegasus on July 30, 2018, 06:09:40 PM
Darval please help is out. Taserz please put a disclaimer to everyone not to try the T9+ firmware overclock as it ruins some of the chains in some way.
Two of miners went out the same way and no matter of resetting can undo the damage. On the other hand, your overclock firmware for S9i worked well.

Why would I put a disclaimer? If you read the thread the guy flashed some other guys firmware and bricked his t9+ and mentioned it here. We are just trying to fix it. Our modification didn't brick his T9+ nor will it even run properly since it is defined in bmminer for an s9 only. The T9+ firmware I built for him is almost the same as the factory in hopes the malicious bmminer was the issue but it is not.
zeus_pegasus
newbie
Activity: 9
Merit: 0
Re: Antminer S9 Volt Rocket Ship firmware mod! ~Time to Max Out Your Bitmain PSU~
July 30, 2018, 06:09:40 PM
#111
Darval please help is out. Taserz please put a disclaimer to everyone not to try the T9+ firmware overclock as it ruins some of the chains in some way.
Two of miners went out the same way and no matter of resetting can undo the damage. On the other hand, your overclock firmware for S9i worked well.
x3aklili
newbie
Activity: 103
Merit: 0
Re: Antminer S9 Volt Rocket Ship firmware mod! ~Time to Max Out Your Bitmain PSU~
July 30, 2018, 03:18:09 PM
#110
Quote from: taserz on July 30, 2018, 04:24:49 AM
Well it is now running the proper bmminer as it is reporting

Code:
Miner Type = T9+

You going to have to hope darval can make it work all the errors are about the software on the pic of the hashboards.

yes i'm waiting for darval...
somename
newbie
Activity: 12
Merit: 5
Re: Antminer S9 Volt Rocket Ship firmware mod! ~Time to Max Out Your Bitmain PSU~
July 30, 2018, 03:02:54 PM
#109
Hi, thank you very much for that firmware. I did some testing with 880mV version and measured the energy consuption at the wall using energy meter. Not sure if it is super accurate, but its just for comparsion. I'm running all miners in oil, but PSU (original bitmain 1600W) are outsite and ambient temp is quite high (35C/95F during day now), therefore I'm not going to run those PSUs at 120%.

S9i (running its original autotune FW)
stock 14TH@1450W
- 675MHz 14.5TH@1530W
- 725MHz 15.6TH@1650W
- 750HHz 16.1TH@1710W - I will be running this setting, HW errors in single digits per hour
- 775MHz 16.7TH@1770W

S9 (original autotune FW, 03/2018 batch I think)
stock 13,8TH@1480W (900mV,900mV,910mV)
- 700MHz 15TH@1580W
- 725MHz 15.6TH@1650W
- 750MHz 16.1TH@1700W



Interesting thing for me is, that temperature on those S9i increased only about 1-degrees, but on S9 it is now +20C (61->81). Do you have any idea why? Does it have something to do with "TempTypeID=1a middle offset=-51"? Maybe those older boards should have different offset?

Also, will you be so kind and compile 870mV FW and put it on github? I would love to try lower voltage and higher clock speed, as I'm oil-cooling it I have no problems with overheating.
taserz
sr. member
Activity: 800
Merit: 294
Created AutoTune to saved the planet! ~USA
Re: Antminer S9 Volt Rocket Ship firmware mod! ~Time to Max Out Your Bitmain PSU~
July 30, 2018, 04:24:49 AM
#108
Quote from: x3aklili on July 29, 2018, 02:49:48 PM
here my current T9+ full kernel log

[...]

maybe help

Well it is now running the proper bmminer as it is reporting

Code:
Miner Type = T9+

You going to have to hope darval can make it work all the errors are about the software on the pic of the hashboards.
taserz
sr. member
Activity: 800
Merit: 294
Created AutoTune to saved the planet! ~USA
Re: Antminer S9 Volt Rocket Ship firmware mod! ~Time to Max Out Your Bitmain PSU~
July 30, 2018, 04:23:12 AM
#107
Quote from: Pizzi_h on July 29, 2018, 02:23:18 PM
Hi great job with the firmware!

Ive managed to change the bmminer to 8.8v 9v and changing back to original. Its an 13.5th with 1600w bitmain psu

At first it worked great with the 8.8v 725mhz. Temperature around
93-97c.

Then it just stopped hashing after a few hours and playing around with the miner.

It works for 3-4 min then it stops to hash. In the log ut says to high temperature. And then all of a sudden i starts to get "lost connection" i have other miners on the same Network and they still work.

Does anyone see anything strange in the log?
Thanks for all the help. Smiley and keep up the work with the coding!

[...]

Try to lower the frequency or use the 9v instead of the 8.8v if your using the 13.5th you got to see which works best.

That is really odd as your miner is not overheating if it was in the 90s as it is set to thermal throttle at 110C.
x3aklili
newbie
Activity: 103
Merit: 0
Re: Antminer S9 Volt Rocket Ship firmware mod! ~Time to Max Out Your Bitmain PSU~
July 29, 2018, 02:49:48 PM
#106
Quote from: taserz on July 29, 2018, 12:54:51 PM
Your welcome man trying what I can to save you from buying a logic board and that idiot that made that dollz firmware came out and said they never even tested it on a t9+. If anyone can do it it's darval.

here my current T9+ full kernel log

Code:
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.14.0-xilinx-gb190cb0-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #57 SMP PREEMPT Fri Dec 9 14:49:22 CST 2016
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Xilinx Zynq
[    0.000000] cma: CMA: reserved 128 MiB at 27800000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 258048
[    0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map e6fd8000
[    0.000000]   Normal zone: 1520 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 194560 pages, LIFO batch:31
[    0.000000]   HighMem zone: 496 pages used for memmap
[    0.000000]   HighMem zone: 63488 pages, LIFO batch:15
[    0.000000] PERCPU: Embedded 8 pages/cpu @e6fc0000 s9088 r8192 d15488 u32768
[    0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 256528
[    0.000000] Kernel command line: noinitrd mem=1008M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 884148K/1032192K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 148044K reserved, 253952K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc06d1374   (6949 kB)
[    0.000000]       .init : 0xc06d2000 - 0xc0705380   ( 205 kB)
[    0.000000]       .data : 0xc0706000 - 0xc074cf78   ( 284 kB)
[    0.000000]        .bss : 0xc074cf84 - 0xc078d9fc   ( 259 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[    0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] ps7-slcr mapped to f0004000
[    0.000000] zynq_clock_init: clkc starts at f0004100
[    0.000000] Zynq clock init
[    0.000014] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[    0.000301] ps7-ttc #0 at f0006000, irq=43
[    0.000604] Console: colour dummy device 80x30
[    0.000641] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[    0.040206] pid_max: default: 32768 minimum: 301
[    0.040427] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.040450] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.042606] CPU: Testing write buffer coherency: ok
[    0.042947] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.043007] Setting up static identity map for 0x4c4af8 - 0x4c4b50
[    0.043232] L310 cache controller enabled
[    0.043252] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[    0.121029] CPU1: Booted secondary processor
[    0.210225] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.210356] Brought up 2 CPUs
[    0.210375] SMP: Total of 2 processors activated.
[    0.210383] CPU: All CPU(s) started in SVC mode.
[    0.211033] devtmpfs: initialized
[    0.213447] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.214652] regulator-dummy: no parameters
[    0.221905] NET: Registered protocol family 16
[    0.224156] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.226426] cpuidle: using governor ladder
[    0.226440] cpuidle: using governor menu
[    0.233799] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[    0.235306] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.235320] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.235433] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xf0080000
[    0.256933] bio: create slab at 0
[    0.258317] vgaarb: loaded
[    0.259014] SCSI subsystem initialized
[    0.259866] usbcore: registered new interface driver usbfs
[    0.260044] usbcore: registered new interface driver hub
[    0.260549] usbcore: registered new device driver usb
[    0.262058] media: Linux media interface: v0.10
[    0.262240] Linux video capture interface: v2.00
[    0.262483] pps_core: LinuxPPS API ver. 1 registered
[    0.262495] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
[    0.262617] PTP clock support registered
[    0.262975] EDAC MC: Ver: 3.0.0
[    0.264020] Advanced Linux Sound Architecture Driver Initialized.
[    0.266839] DMA-API: preallocated 4096 debug entries
[    0.266853] DMA-API: debugging enabled by kernel config
[    0.266928] Switched to clocksource arm_global_timer
[    0.286709] NET: Registered protocol family 2
[    0.287476] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.287571] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.287730] TCP: Hash tables configured (established 8192 bind 8192)
[    0.287797] TCP: reno registered
[    0.287816] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.287869] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.288130] NET: Registered protocol family 1
[    0.288482] RPC: Registered named UNIX socket transport module.
[    0.288493] RPC: Registered udp transport module.
[    0.288502] RPC: Registered tcp transport module.
[    0.288510] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.288523] PCI: CLS 0 bytes, default 64
[    0.288969] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    0.290982] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.292404] bounce pool size: 64 pages
[    0.293289] jffs2: version 2.2. (NAND) ? 2001-2006 Red Hat, Inc.
[    0.293491] msgmni has been set to 1486
[    0.294265] io scheduler noop registered
[    0.294279] io scheduler deadline registered
[    0.294322] io scheduler cfq registered (default)
[    0.307061] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[    0.307081] dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[    0.429286] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[    1.002088] console [ttyPS0] enabled
[    1.006369] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to f0068000
[    1.013995] [drm] Initialized drm 1.1.0 20060810
[    1.031014] brd: module loaded
[    1.040385] loop: module loaded
[    1.050104] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[    1.055851] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[    1.063685] libphy: XEMACPS mii bus: probed
[    1.068170] ------------- phy_id = 0x3625e62
[    1.072898] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[    1.081502] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.088248] ehci-pci: EHCI PCI platform driver
[    1.095462] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[    1.102316] usbcore: registered new interface driver usb-storage
[    1.109188] mousedev: PS/2 mouse device common for all mice
[    1.115270] i2c /dev entries driver
[    1.122218] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[    1.127736] cpufreq_cpu0: failed to get cpu0 regulator: -19
[    1.133610] Xilinx Zynq CpuIdle Driver started
[    1.138506] sdhci: Secure Digital Host Controller Interface driver
[    1.144604] sdhci: Copyright(c) Pierre Ossman
[    1.148970] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.155746] mmc0: no vqmmc regulator found
[    1.159858] mmc0: no vmmc regulator found
[    1.196946] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[    1.209831] usbcore: registered new interface driver usbhid
[    1.215338] usbhid: USB HID core driver
[    1.224031] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[    1.232340] nand: Micron MT29F2G08ABAEAWP
[    1.238319] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[    1.244224] Bad block table found at page 131008, version 0x01
[    1.250494] Bad block table found at page 130944, version 0x01
[    1.256577] 3 ofpart partitions found on MTD device pl353-nand
[    1.262361] Creating 3 MTD partitions on "pl353-nand":
[    1.267484] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[    1.275480] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[    1.282796] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[    1.291752] TCP: cubic registered
[    1.294989] NET: Registered protocol family 17
[    1.299696] Registering SWP/SWPB emulation handler
[    1.305592] regulator-dummy: disabling
[    1.309925] UBI: attaching mtd1 to ubi0
[    1.396289] mmc0: new high speed SDHC card at address 59b4
[    1.402279] mmcblk0: mmc0:59b4 USDU1 14.9 GiB (ro)
[    1.408525]  mmcblk0: p1
[    1.840387] UBI: scanning is finished
[    1.852086] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[    1.859171] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    1.865915] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    1.872618] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[    1.879477] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[    1.885444] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[    1.892576] UBI: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 862493722
[    1.901520] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[    1.910736] UBI: background thread "ubi_bgt0d" started, PID 1086
[    1.910741] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    1.914641] ALSA device list:
[    1.914644]   No soundcards found.
[    1.931108] UBIFS: background thread "ubifs_bgt0_0" started, PID 1088
[    1.960368] UBIFS: recovery needed
[    2.212829] UBIFS: recovery completed
[    2.216507] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[    2.222458] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    2.231561] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[    2.241450] UBIFS: reserved for root: 0 bytes (0 KiB)
[    2.246479] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 2A24A8E1-2021-4A54-8A4E-D8E294AE00E5, small LPT model
[    2.257784] VFS: Mounted root (ubifs filesystem) on device 0:11.
[    2.264502] devtmpfs: mounted
[    2.267630] Freeing unused kernel memory: 204K (c06d2000 - c0705000)
[    3.105032] random: dd urandom read with 8 bits of entropy available
[    3.496966]
[    3.496966] bcm54xx_config_init
[    4.106970]
[    4.106970] bcm54xx_config_init
[    8.107831] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[    8.113923] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[   22.786372] In axi fpga driver!
[   22.789466] request_mem_region OK!
[   22.792836] AXI fpga dev virtual address is 0xf0200000
[   22.797964] *base_vir_addr = 0xc510
[   22.813246] In fpga mem driver!
[   22.816403] request_mem_region OK!
[   22.820019] fpga mem virtual address is 0xf3000000
[   23.616963]
[   23.616963] bcm54xx_config_init
[   24.246947]
[   24.246947] bcm54xx_config_init
[   28.247805] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[   28.253824] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[  530.016062] random: nonblocking pool is initialized
This is XILINX board. Totalram:       1039794176
Detect 1GB control board of XILINX
DETECT HW version=8000c510
miner ID : 815255ce2c008814
Miner Type = T9+
AsicType = 1387
real AsicNum = 18
use critical mode to search freq...
get PLUG ON=0x07003f0e
Find hashboard on Chain[1]
Find hashboard on Chain[2]
Find hashboard on Chain[3]
Find hashboard on Chain[8]
Find hashboard on Chain[9]
Find hashboard on Chain[10]
Find hashboard on Chain[11]
Find hashboard on Chain[12]
Find hashboard on Chain[13]
set_reset_allhashboard = 0x0000ffff
chain[1] PIC jump to app
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[1]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[1]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[1]!
Check chain[1] PIC fw version=0xff
chain[2] PIC jump to app
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[2]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[2]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[2]!
Check chain[2] PIC fw version=0xff
chain[3] PIC jump to app
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[3]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[3]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[3]!
Check chain[3] PIC fw version=0xff
Chain[1] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
chain[1]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
has freq in PIC, will disable freq setting.
chain[1] has freq in PIC and will jump over...
Chain[1] has core num in PIC
Chain[2] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
chain[2]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
has freq in PIC, will disable freq setting.
chain[2] has freq in PIC and will jump over...
Chain[2] has core num in PIC
Chain[3] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
chain[3]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
has freq in PIC, will disable freq setting.
chain[3] has freq in PIC and will jump over...
Chain[3] has core num in PIC
has freq in PIC, will disable freq setting.
chain[8] has freq in PIC and will jump over...
Chain[8] has core num in PIC
has freq in PIC, will disable freq setting.
chain[9] has freq in PIC and will jump over...
Chain[9] has core num in PIC
has freq in PIC, will disable freq setting.
chain[10] has freq in PIC and will jump over...
Chain[10] has core num in PIC
has freq in PIC, will disable freq setting.
chain[11] has freq in PIC and will jump over...
Chain[11] has core num in PIC
has freq in PIC, will disable freq setting.
chain[12] has freq in PIC and will jump over...
Chain[12] has core num in PIC
has freq in PIC, will disable freq setting.
chain[13] has freq in PIC and will jump over...
Chain[13] has core num in PIC
get PIC voltage=11 on chain[1], value=870
get PIC voltage=11 on chain[2], value=870
get PIC voltage=11 on chain[3], value=870
get PIC voltage=11 on chain[8], value=870
get PIC voltage=11 on chain[9], value=870
get PIC voltage=11 on chain[10], value=870
get PIC voltage=11 on chain[11], value=870
get PIC voltage=11 on chain[12], value=870
get PIC voltage=11 on chain[13], value=870
dsPIC33EP16GS202_pic_heart_beat failed on Chain[1]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[1]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[1]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[2]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[2]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[2]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[3]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[1]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[3]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[1]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[3]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[1]!
set_reset_allhashboard = 0x00000000
chain[8] temp offset record: 1,0,0,0,0,0,37,28
chain[8] temp chip I2C addr=0x98
chain[8] has no middle temp, use special fix mode.
chain[10] temp offset record: 1,0,0,0,0,0,37,28
chain[10] temp chip I2C addr=0x98
chain[10] has no middle temp, use special fix mode.
chain[12] temp offset record: 1,0,0,0,0,0,37,28
chain[12] temp chip I2C addr=0x98
chain[12] has no middle temp, use special fix mode.
dsPIC33EP16GS202_pic_heart_beat failed on Chain[1]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[1]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[1]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[2]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[2]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[2]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[3]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[3]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[3]!
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
CRC error counter=0
set command mode to VIL

--- check asic number
After Get ASIC NUM CRC error counter=0
set_baud=0
The min freq=700
set real timeout 52, need sleep=379392
After TEST CRC error counter=0
search freq for 1 times, completed chain = 9, total chain num = 9
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
restart Miner chance num=2
waiting for receive_func to exit!
waiting for pic heart to exit!
bmminer not found= 1657 root       0:00 grep bmminer

bmminer not found, restart bmminer ...
This is user mode for mining
Detect 1GB control board of XILINX
Miner Type = T9+
Miner compile time: Fri Nov 24 23:19:16 EST 2017 type: Antminer T9+set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
set_reset_allhashboard = 0x0000ffff
miner ID : 815255ce2c008814
set_reset_allhashboard = 0x0000ffff
Checking fans!get fan[5] speed=6240
get fan[2] speed=4560
get fan[5] speed=6240
get fan[2] speed=4560
get fan[5] speed=6240
chain[1] PIC jump to app
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[1]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[1]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[1]!
Check chain[1] PIC fw version=0xff
Chain[1] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
chain[1]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
Chain[J2] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J2] test patten OK temp=-1
chain[2] PIC jump to app
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[2]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[2]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[2]!
Check chain[2] PIC fw version=0xff
Chain[2] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
chain[2]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
Chain[J3] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J3] test patten OK temp=-1
chain[3] PIC jump to app
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[3]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[3]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[3]!
Check chain[3] PIC fw version=0xff
Chain[3] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
chain[3]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
Chain[J4] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J4] test patten OK temp=-1
Chain[J9] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J9] test patten OK temp=-1
Chain[J10] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J10] test patten OK temp=-1
Chain[J11] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J11] test patten OK temp=-1
Chain[J12] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J12] test patten OK temp=-1
Chain[J13] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J13] test patten OK temp=-1
Chain[J14] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J14] test patten OK temp=-1
Chain[J2] will use voltage=930 [1] to open core
set_Voltage_S9_plus_plus_BM1387_54 failed on Chain[1]!

set_Voltage_S9_plus_plus_BM1387_54 failed on Chain[1]!

set_Voltage_S9_plus_plus_BM1387_54 failed on Chain[1]!

Chain[J3] will use voltage=930 [1] to open core
set_Voltage_S9_plus_plus_BM1387_54 failed on Chain[2]!

set_Voltage_S9_plus_plus_BM1387_54 failed on Chain[2]!

set_Voltage_S9_plus_plus_BM1387_54 failed on Chain[2]!

Chain[J4] will use voltage=930 [1] to open core
set_Voltage_S9_plus_plus_BM1387_54 failed on Chain[3]!

set_Voltage_S9_plus_plus_BM1387_54 failed on Chain[3]!

set_Voltage_S9_plus_plus_BM1387_54 failed on Chain[3]!

Chain[J9] will use voltage=930 [1] to open core
Chain[J10] will use voltage=930 [1] to open core
Chain[J11] will use voltage=930 [1] to open core
Chain[J12] will use voltage=930 [1] to open core
Chain[J13] will use voltage=930 [1] to open core
Chain[J14] will use voltage=930 [1] to open core
Chain[J2] orignal chain_voltage_pic=11 value=870
Chain[J3] orignal chain_voltage_pic=11 value=870
Chain[J4] orignal chain_voltage_pic=11 value=870
Chain[J9] orignal chain_voltage_pic=11 value=870
Chain[J10] orignal chain_voltage_pic=11 value=870
Chain[J11] orignal chain_voltage_pic=11 value=870
Chain[J12] orignal chain_voltage_pic=11 value=870
Chain[J13] orignal chain_voltage_pic=11 value=870
Chain[J14] orignal chain_voltage_pic=11 value=870
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
T9+ try get asic num for the 1 time
Chain[J2] has 0 asic
set_reset_allhashboard = 0x0000ffff
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
set_reset_allhashboard = 0x00000000
T9+ try get asic num for the 2 time
Chain[J2] has 0 asic
set_reset_allhashboard = 0x0000ffff
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
set_reset_allhashboard = 0x00000000
T9+ try get asic num for the 3 time
Chain[J2] has 0 asic
set_reset_allhashboard = 0x0000ffff
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
set_reset_allhashboard = 0x00000000
T9+ try get asic num for the 4 time
Chain[J2] has 0 asic
set_reset_allhashboard = 0x0000ffff
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
set_reset_allhashboard = 0x00000000
T9+ try get asic num for the 5 time
Chain[J2] has 0 asic
set_reset_allhashboard = 0x0000ffff
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[3]!
set_reset_allhashboard = 0x00000000
T9+ try get asic num for the 6 time
Chain[J2] has 0 asic
miner total rate=0GH/s fixed rate=0GH/s

Miner fix freq ...
max freq = 100
set baud=1
setStartTimePoint total_tv_start_sys=392 total_tv_end_sys=393
restartNum = 2 , auto-reinit enabled...
do read_temp_func once...
do check_asic_reg 0x08
Done check_asic_reg
set FAN speed according to: temp_highest=0 temp_top1[PWM_T]=0 temp_top1[TEMP_POS_LOCAL]=0 temp_change=0 fix_fan_steps=0
set full FAN speed...
FAN PWM: 100
read_temp_func Done!
CRC error counter=10057

maybe help
Pizzi_h
newbie
Activity: 9
Merit: 0
Re: Antminer S9 Volt Rocket Ship firmware mod! ~Time to Max Out Your Bitmain PSU~
July 29, 2018, 02:23:18 PM
#105
Hi great job with the firmware!

Ive managed to change the bmminer to 8.8v 9v and changing back to original. Its an 13.5th with 1600w bitmain psu

At first it worked great with the 8.8v 725mhz. Temperature around
93-97c.

Then it just stopped hashing after a few hours and playing around with the miner.

It works for 3-4 min then it stops to hash. In the log ut says to high temperature. And then all of a sudden i starts to get "lost connection" i have other miners on the same Network and they still work.

Does anyone see anything strange in the log?
Thanks for all the help. Smiley and keep up the work with the coding!

Code:
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.14.0-xilinx-gb190cb0-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #57 SMP PREEMPT Fri Dec 9 14:49:22 CST 2016
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Xilinx Zynq
[    0.000000] cma: CMA: reserved 128 MiB at 27800000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 258048
[    0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map e6fd8000
[    0.000000]   Normal zone: 1520 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 194560 pages, LIFO batch:31
[    0.000000]   HighMem zone: 496 pages used for memmap
[    0.000000]   HighMem zone: 63488 pages, LIFO batch:15
[    0.000000] PERCPU: Embedded 8 pages/cpu @e6fc0000 s9088 r8192 d15488 u32768
[    0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 256528
[    0.000000] Kernel command line: noinitrd mem=1008M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 884148K/1032192K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 148044K reserved, 253952K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc06d1374   (6949 kB)
[    0.000000]       .init : 0xc06d2000 - 0xc0705380   ( 205 kB)
[    0.000000]       .data : 0xc0706000 - 0xc074cf78   ( 284 kB)
[    0.000000]        .bss : 0xc074cf84 - 0xc078d9fc   ( 259 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[    0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] ps7-slcr mapped to f0004000
[    0.000000] zynq_clock_init: clkc starts at f0004100
[    0.000000] Zynq clock init
[    0.000014] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[    0.000301] ps7-ttc #0 at f0006000, irq=43
[    0.000606] Console: colour dummy device 80x30
[    0.000642] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[    0.040203] pid_max: default: 32768 minimum: 301
[    0.040426] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.040448] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.042596] CPU: Testing write buffer coherency: ok
[    0.042947] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.043007] Setting up static identity map for 0x4c4af8 - 0x4c4b50
[    0.043229] L310 cache controller enabled
[    0.043248] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[    0.121033] CPU1: Booted secondary processor
[    0.210224] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.210356] Brought up 2 CPUs
[    0.210375] SMP: Total of 2 processors activated.
[    0.210383] CPU: All CPU(s) started in SVC mode.
[    0.211047] devtmpfs: initialized
[    0.213450] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.214655] regulator-dummy: no parameters
[    0.221906] NET: Registered protocol family 16
[    0.224156] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.226426] cpuidle: using governor ladder
[    0.226440] cpuidle: using governor menu
[    0.233803] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[    0.235311] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.235325] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.235437] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xf0080000
[    0.257093] bio: create slab at 0
[    0.258501] vgaarb: loaded
[    0.259196] SCSI subsystem initialized
[    0.260062] usbcore: registered new interface driver usbfs
[    0.260374] usbcore: registered new interface driver hub
[    0.260611] usbcore: registered new device driver usb
[    0.261145] media: Linux media interface: v0.10
[    0.261308] Linux video capture interface: v2.00
[    0.261550] pps_core: LinuxPPS API ver. 1 registered
[    0.261562] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
[    0.261689] PTP clock support registered
[    0.262042] EDAC MC: Ver: 3.0.0
[    0.263113] Advanced Linux Sound Architecture Driver Initialized.
[    0.265953] DMA-API: preallocated 4096 debug entries
[    0.265967] DMA-API: debugging enabled by kernel config
[    0.266046] Switched to clocksource arm_global_timer
[    0.287228] NET: Registered protocol family 2
[    0.287885] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.287979] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.288138] TCP: Hash tables configured (established 8192 bind 8192)
[    0.288206] TCP: reno registered
[    0.288225] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.288275] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.288543] NET: Registered protocol family 1
[    0.288904] RPC: Registered named UNIX socket transport module.
[    0.288916] RPC: Registered udp transport module.
[    0.288925] RPC: Registered tcp transport module.
[    0.288933] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.288946] PCI: CLS 0 bytes, default 64
[    0.289384] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    0.291401] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.292792] bounce pool size: 64 pages
[    0.293681] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.293877] msgmni has been set to 1486
[    0.294642] io scheduler noop registered
[    0.294656] io scheduler deadline registered
[    0.294702] io scheduler cfq registered (default)
[    0.303544] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[    0.303565] dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[    0.427215] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[    0.999677] console [ttyPS0] enabled
[    1.003954] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to f0068000
[    1.011571] [drm] Initialized drm 1.1.0 20060810
[    1.028558] brd: module loaded
[    1.037936] loop: module loaded
[    1.047684] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[    1.053436] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[    1.061279] libphy: XEMACPS mii bus: probed
[    1.065650] ------------- phy_id = 0x3625e62
[    1.070554] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[    1.079157] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.085783] ehci-pci: EHCI PCI platform driver
[    1.093065] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[    1.099925] usbcore: registered new interface driver usb-storage
[    1.106883] mousedev: PS/2 mouse device common for all mice
[    1.112978] i2c /dev entries driver
[    1.119863] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[    1.125341] cpufreq_cpu0: failed to get cpu0 regulator: -19
[    1.131262] Xilinx Zynq CpuIdle Driver started
[    1.136127] sdhci: Secure Digital Host Controller Interface driver
[    1.142224] sdhci: Copyright(c) Pierre Ossman
[    1.146605] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.153364] mmc0: no vqmmc regulator found
[    1.157403] mmc0: no vmmc regulator found
[    1.196072] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[    1.204757] usbcore: registered new interface driver usbhid
[    1.210264] usbhid: USB HID core driver
[    1.214962] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[    1.221263] nand: Micron MT29F2G08ABAEAWP
[    1.225225] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[    1.231164] Bad block table found at page 131008, version 0x01
[    1.237384] Bad block table found at page 130944, version 0x01
[    1.243438] 3 ofpart partitions found on MTD device pl353-nand
[    1.249227] Creating 3 MTD partitions on "pl353-nand":
[    1.254316] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[    1.262376] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[    1.269701] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[    1.278667] TCP: cubic registered
[    1.281907] NET: Registered protocol family 17
[    1.286620] Registering SWP/SWPB emulation handler
[    1.292502] regulator-dummy: disabling
[    1.296859] UBI: attaching mtd1 to ubi0
[    1.823005] UBI: scanning is finished
[    1.834524] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[    1.841601] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    1.848364] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    1.855028] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[    1.861905] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[    1.867886] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[    1.874994] UBI: max/mean erase counter: 16356/13952, WL threshold: 4096, image sequence number: 1984962504
[    1.884730] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[    1.893947] UBI: background thread "ubi_bgt0d" started, PID 1080
[    1.893952] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    1.897921] ALSA device list:
[    1.897925]   No soundcards found.
[    1.914321] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082
[    1.943481] UBIFS: recovery needed
[    2.000112] UBIFS: recovery completed
[    2.003780] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[    2.009723] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    2.018864] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[    2.028721] UBIFS: reserved for root: 0 bytes (0 KiB)
[    2.033747] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 56FDF5FA-8D29-4AA7-95D4-1C2E28C7C4E9, small LPT model
[    2.045511] VFS: Mounted root (ubifs filesystem) on device 0:11.
[    2.052932] devtmpfs: mounted
[    2.056035] Freeing unused kernel memory: 204K (c06d2000 - c0705000)
[    2.900198] random: dd urandom read with 0 bits of entropy available
[    3.296070]
[    3.296070] bcm54xx_config_init
[    3.906090]
[    3.906090] bcm54xx_config_init
[    6.906924] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[    6.913016] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[   30.436845] In axi fpga driver!
[   30.439918] request_mem_region OK!
[   30.443305] AXI fpga dev virtual address is 0xf01fe000
[   30.448451] *base_vir_addr = 0x8c510
[   30.463183] In fpga mem driver!
[   30.466591] request_mem_region OK!
[   30.470100] fpga mem virtual address is 0xf3000000
[   31.235980]
[   31.235980] bcm54xx_config_init
[   31.865896]
[   31.865896] bcm54xx_config_init
[   34.866450] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[   34.872468] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[  186.015364] random: nonblocking pool is initialized
[  311.934609] UBI: scrubbed PEB 859 (LEB 0:2), data moved to PEB 883
[  324.178183] UBI: scrubbed PEB 406 (LEB 0:1), data moved to PEB 795
[  328.313711] UBI: scrubbed PEB 27 (LEB 0:1), data moved to PEB 468
[  367.822069] UBI: scrubbed PEB 44 (LEB 0:1), data moved to PEB 805
[  379.897076] UBI: scrubbed PEB 812 (LEB 0:1), data moved to PEB 883
[ 1017.466462] UBI: scrubbed PEB 872 (LEB 0:2), data moved to PEB 884
[ 1107.746481] UBI: scrubbed PEB 1 (LEB 0:2), data moved to PEB 901
[ 1156.072693] UBI: scrubbed PEB 551 (LEB 0:1), data moved to PEB 869
Detect 1GB control board of XILINX
Miner Type = S9
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x0000ffff
Check chain[5] PIC fw version=0x03
Check chain[6] PIC fw version=0x03
Check chain[7] PIC fw version=0x03
Fix freq=550 Chain[5] voltage_pic=6 value=940
Fix freq=550 Chain[6] voltage_pic=6 value=940
Fix freq=550 Chain[7] voltage_pic=6 value=940
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
Chain[J6] has 63 asic
Chain[J7] has 63 asic
Chain[J8] has 63 asic
Chain[J6] has no freq in PIC, set default freq=550M
Chain[J6] has no core num in PIC
Chain[J7] has no freq in PIC, set default freq=550M
Chain[J7] has no core num in PIC
Chain[J8] has no freq in PIC, set default freq=550M
Chain[J8] has no core num in PIC

Miner fix freq ...
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Asic[ 0]:550
Asic[ 1]:550 Asic[ 2]:550 Asic[ 3]:550 Asic[ 4]:550 Asic[ 5]:550 Asic[ 6]:550 Asic[ 7]:550 Asic[ 8]:550
Asic[ 9]:550 Asic[10]:550 Asic[11]:550 Asic[12]:550 Asic[13]:550 Asic[14]:550 Asic[15]:550 Asic[16]:550
Asic[17]:550 Asic[18]:550 Asic[19]:550 Asic[20]:550 Asic[21]:550 Asic[22]:550 Asic[23]:550 Asic[24]:550
Asic[25]:550 Asic[26]:550 Asic[27]:550 Asic[28]:550 Asic[29]:550 Asic[30]:550 Asic[31]:550 Asic[32]:550
Asic[33]:550 Asic[34]:550 Asic[35]:550 Asic[36]:550 Asic[37]:550 Asic[38]:550 Asic[39]:550 Asic[40]:550
Asic[41]:550 Asic[42]:550 Asic[43]:550 Asic[44]:550 Asic[45]:550 Asic[46]:550 Asic[47]:550 Asic[48]:550
Asic[49]:550 Asic[50]:550 Asic[51]:550 Asic[52]:550 Asic[53]:550 Asic[54]:550 Asic[55]:550 Asic[56]:550
Asic[57]:550 Asic[58]:550 Asic[59]:550 Asic[60]:550 Asic[61]:550 Asic[62]:550
Chain:5 max freq=550
Chain:5 min freq=550

read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Asic[ 0]:550
Asic[ 1]:550 Asic[ 2]:550 Asic[ 3]:550 Asic[ 4]:550 Asic[ 5]:550 Asic[ 6]:550 Asic[ 7]:550 Asic[ 8]:550
Asic[ 9]:550 Asic[10]:550 Asic[11]:550 Asic[12]:550 Asic[13]:550 Asic[14]:550 Asic[15]:550 Asic[16]:550
Asic[17]:550 Asic[18]:550 Asic[19]:550 Asic[20]:550 Asic[21]:550 Asic[22]:550 Asic[23]:550 Asic[24]:550
Asic[25]:550 Asic[26]:550 Asic[27]:550 Asic[28]:550 Asic[29]:550 Asic[30]:550 Asic[31]:550 Asic[32]:550
Asic[33]:550 Asic[34]:550 Asic[35]:550 Asic[36]:550 Asic[37]:550 Asic[38]:550 Asic[39]:550 Asic[40]:550
Asic[41]:550 Asic[42]:550 Asic[43]:550 Asic[44]:550 Asic[45]:550 Asic[46]:550 Asic[47]:550 Asic[48]:550
Asic[49]:550 Asic[50]:550 Asic[51]:550 Asic[52]:550 Asic[53]:550 Asic[54]:550 Asic[55]:550 Asic[56]:550
Asic[57]:550 Asic[58]:550 Asic[59]:550 Asic[60]:550 Asic[61]:550 Asic[62]:550
Chain:6 max freq=550
Chain:6 min freq=550

read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Asic[ 0]:550
Asic[ 1]:550 Asic[ 2]:550 Asic[ 3]:550 Asic[ 4]:550 Asic[ 5]:550 Asic[ 6]:550 Asic[ 7]:550 Asic[ 8]:550
Asic[ 9]:550 Asic[10]:550 Asic[11]:550 Asic[12]:550 Asic[13]:550 Asic[14]:550 Asic[15]:550 Asic[16]:550
Asic[17]:550 Asic[18]:550 Asic[19]:550 Asic[20]:550 Asic[21]:550 Asic[22]:550 Asic[23]:550 Asic[24]:550
Asic[25]:550 Asic[26]:550 Asic[27]:550 Asic[28]:550 Asic[29]:550 Asic[30]:550 Asic[31]:550 Asic[32]:550
Asic[33]:550 Asic[34]:550 Asic[35]:550 Asic[36]:550 Asic[37]:550 Asic[38]:550 Asic[39]:550 Asic[40]:550
Asic[41]:550 Asic[42]:550 Asic[43]:550 Asic[44]:550 Asic[45]:550 Asic[46]:550 Asic[47]:550 Asic[48]:550
Asic[49]:550 Asic[50]:550 Asic[51]:550 Asic[52]:550 Asic[53]:550 Asic[54]:550 Asic[55]:550 Asic[56]:550
Asic[57]:550 Asic[58]:550 Asic[59]:550 Asic[60]:550 Asic[61]:550 Asic[62]:550
Chain:7 max freq=550
Chain:7 min freq=550

max freq = 550
set baud=2
Chain[J6] PIC temp offset=62,0,0,0,0,0,35,28
Chain[J6] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[5] chip[244] local:27 remote:30 offset:27
Chain[J6] chip[244] get middle temp offset=27 typeID=55
Chain[J6] chip[136] use PIC middle temp offset=28 typeID=00
Warning: Chain[J6] has no temp offset in PIC! will fix it
New offset Chain[5] chip[244] local:27 remote:30 offset:27
Chain[J6] chip[244] get middle temp offset=27 typeID=55
Chain[J7] PIC temp offset=62,0,0,0,0,0,35,28
Chain[J7] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[6] chip[244] local:27 remote:32 offset:25
Chain[J7] chip[244] get middle temp offset=25 typeID=55
Chain[J7] chip[136] use PIC middle temp offset=28 typeID=00
Warning: Chain[J7] has no temp offset in PIC! will fix it
New offset Chain[6] chip[244] local:27 remote:32 offset:25
Chain[J7] chip[244] get middle temp offset=25 typeID=55
Chain[J8] PIC temp offset=62,0,0,0,0,0,35,28
Chain[J8] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[7] chip[244] local:28 remote:32 offset:26
Chain[J8] chip[244] get middle temp offset=26 typeID=55
Chain[J8] chip[136] use PIC middle temp offset=28 typeID=00
Warning: Chain[J8] has no temp offset in PIC! will fix it
New offset Chain[7] chip[244] local:28 remote:32 offset:26
Chain[J8] chip[244] get middle temp offset=26 typeID=55
Chain[J6] set working voltage=940 [6]
Chain[J7] set working voltage=940 [6]
Chain[J8] set working voltage=940 [6]
setStartTimePoint total_tv_start_sys=80 total_tv_end_sys=81
restartNum = 2 , auto-reinit enabled...
Fatal Error: Temperature is too high!
Fatal Error: Temperature is too high!
Fatal Error: Temperature is too high!
Fatal Error: Temperature is too high!
Fatal Error: Temperature is too high!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
do read_temp_func once...
do check_asic_reg 0x08

get RT hashrate from Chain[5]: (asic index start from 1-63)

get RT hashrate from Chain[6]: (asic index start from 1-63)

get RT hashrate from Chain[7]: (asic index start from 1-63)
Check Chain[J6] ASIC RT error: (asic index start from 1-63)
Check Chain[J7] ASIC RT error: (asic index start from 1-63)
Check Chain[J8] ASIC RT error: (asic index start from 1-63)
Done check_asic_reg
do read temp on Chain[5]
Chain[5] Chip[62] TempTypeID=55 middle offset=27
read failed, old value: Chain[5] Chip[62] local Temp=91
read failed on Chain[5] Chip[62] middle Temp old value:97
Done read temp on Chain[5]
do read temp on Chain[6]
Chain[6] Chip[62] TempTypeID=55 middle offset=25
read failed, old value: Chain[6] Chip[62] local Temp=89
read failed on Chain[6] Chip[62] middle Temp old value:92
Done read temp on Chain[6]
do read temp on Chain[7]
Chain[7] Chip[62] TempTypeID=55 middle offset=26
read failed, old value: Chain[7] Chip[62] local Temp=89
read failed on Chain[7] Chip[62] middle Temp old value:92
Done read temp on Chain[7]
set FAN speed according to: temp_highest=97 temp_top1[PWM_T]=97 temp_top1[TEMP_POS_LOCAL]=91 temp_change=17 fix_fan_steps=0
set full FAN speed...
FAN PWM: 100
read_temp_func Done!
CRC error counter=0  
taserz
sr. member
Activity: 800
Merit: 294
Created AutoTune to saved the planet! ~USA
Re: Antminer S9 Volt Rocket Ship firmware mod! ~Time to Max Out Your Bitmain PSU~
July 29, 2018, 12:54:51 PM
#104
Quote from: x3aklili on July 29, 2018, 09:23:06 AM
i hope too. also your trying is appreciated. you spent a lot of time on my case Smiley

Your welcome man trying what I can to save you from buying a logic board and that idiot that made that dollz firmware came out and said they never even tested it on a t9+. If anyone can do it it's darval.
x3aklili
newbie
Activity: 103
Merit: 0
Re: Antminer S9 Volt Rocket Ship firmware mod! ~Time to Max Out Your Bitmain PSU~
July 29, 2018, 09:23:06 AM
#103
Quote from: taserz on July 29, 2018, 08:53:45 AM
On the plus side if it works. The bmminer I made allows you to overclock it haha. It's the same firmware as the 8.8v for the s9 just for the T9 firmware hopefully darval will be able to help you out!

i hope too. also your trying is appreciated. you spent a lot of time on my case Smiley
taserz
sr. member
Activity: 800
Merit: 294
Created AutoTune to saved the planet! ~USA
Re: Antminer S9 Volt Rocket Ship firmware mod! ~Time to Max Out Your Bitmain PSU~
July 29, 2018, 08:53:45 AM
#102
Quote from: darval on July 29, 2018, 07:50:44 AM
I spent the last couple hours confirming I have the info I need to be able to reprogram the pic firmware.  Whether it works in the particular case / problem you have is a different issue.  It will take a little more work than I had hoped (my code needs more refactoring as the S9 and T9's talk to the pic in a different way).  I don't know that I will get it done today, but I will continue to work on it.

On the plus side if it works. The bmminer I made allows you to overclock it haha. It's the same firmware as the 8.8v for the s9 just for the T9 firmware hopefully darval will be able to help you out!
x3aklili
newbie
Activity: 103
Merit: 0
Re: Antminer S9 Volt Rocket Ship firmware mod! ~Time to Max Out Your Bitmain PSU~
July 29, 2018, 07:56:18 AM
#101
Quote from: darval on July 29, 2018, 07:50:44 AM
I spent the last couple hours confirming I have the info I need to be able to reprogram the pic firmware.  Whether it works in the particular case / problem you have is a different issue.  It will take a little more work than I had hoped (my code needs more refactoring as the S9 and T9's talk to the pic in a different way).  I don't know that I will get it done today, but I will continue to work on it.

i hope you done this. you can reach me by amir_new_cents[at]yahoo[dot]com
darval
member
Activity: 93
Merit: 10
Re: Antminer S9 Volt Rocket Ship firmware mod! ~Time to Max Out Your Bitmain PSU~
July 29, 2018, 07:50:44 AM
#100
Quote from: x3aklili on July 29, 2018, 06:33:59 AM
if you are really able to fix that you will 0.003BTC rewarded.

I spent the last couple hours confirming I have the info I need to be able to reprogram the pic firmware.  Whether it works in the particular case / problem you have is a different issue.  It will take a little more work than I had hoped (my code needs more refactoring as the S9 and T9's talk to the pic in a different way).  I don't know that I will get it done today, but I will continue to work on it.
x3aklili
newbie
Activity: 103
Merit: 0
Re: Antminer S9 Volt Rocket Ship firmware mod! ~Time to Max Out Your Bitmain PSU~
July 29, 2018, 06:33:59 AM
#99
Quote from: darval on July 29, 2018, 05:27:18 AM
I am going to take a look at this today.  I wrote / modified a program to help restore the pic firmware on an L3+ ( https://github.com/darval/bitmain-tools ) and I am going to see if I can modify it to work for a T9+.  The pic is a microcontroller on each hash board.  Usually when it (bmminer) tries to get the version and it fails (-1 or 0xff), it means the pic firmware got trashed.  My program has a mode to try to restore it.  It currently doesn't work on the T9+, so don't try it yet, but if I am successful, I will update it and post about it here.  Then you can try it out.  Like anything, this stuff is all use at your own risk. Smiley

if you are really able to fix that you will 0.003BTC rewarded.
darval
member
Activity: 93
Merit: 10
Re: Antminer S9 Volt Rocket Ship firmware mod! ~Time to Max Out Your Bitmain PSU~
July 29, 2018, 05:27:18 AM
#98
Quote from: x3aklili on July 28, 2018, 08:10:23 PM
[...]

here my friend , this is my log after your new bmminer designed to me.

I am going to take a look at this today.  I wrote / modified a program to help restore the pic firmware on an L3+ ( https://github.com/darval/bitmain-tools ) and I am going to see if I can modify it to work for a T9+.  The pic is a microcontroller on each hash board.  Usually when it (bmminer) tries to get the version and it fails (-1 or 0xff), it means the pic firmware got trashed.  My program has a mode to try to restore it.  It currently doesn't work on the T9+, so don't try it yet, but if I am successful, I will update it and post about it here.  Then you can try it out.  Like anything, this stuff is all use at your own risk. Smiley
x3aklili
newbie
Activity: 103
Merit: 0
Re: Antminer S9 Volt Rocket Ship firmware mod! ~Time to Max Out Your Bitmain PSU~
July 28, 2018, 08:10:23 PM
#97
Code:
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.14.0-xilinx-gb190cb0-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #57 SMP PREEMPT Fri Dec 9 14:49:22 CST 2016
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Xilinx Zynq
[    0.000000] cma: CMA: reserved 128 MiB at 27800000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 258048
[    0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map e6fd8000
[    0.000000]   Normal zone: 1520 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 194560 pages, LIFO batch:31
[    0.000000]   HighMem zone: 496 pages used for memmap
[    0.000000]   HighMem zone: 63488 pages, LIFO batch:15
[    0.000000] PERCPU: Embedded 8 pages/cpu @e6fc0000 s9088 r8192 d15488 u32768
[    0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 256528
[    0.000000] Kernel command line: noinitrd mem=1008M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 884148K/1032192K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 148044K reserved, 253952K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc06d1374   (6949 kB)
[    0.000000]       .init : 0xc06d2000 - 0xc0705380   ( 205 kB)
[    0.000000]       .data : 0xc0706000 - 0xc074cf78   ( 284 kB)
[    0.000000]        .bss : 0xc074cf84 - 0xc078d9fc   ( 259 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[    0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] ps7-slcr mapped to f0004000
[    0.000000] zynq_clock_init: clkc starts at f0004100
[    0.000000] Zynq clock init
[    0.000015] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[    0.000308] ps7-ttc #0 at f0006000, irq=43
[    0.000616] Console: colour dummy device 80x30
[    0.000653] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[    0.040209] pid_max: default: 32768 minimum: 301
[    0.040433] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.040455] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.042600] CPU: Testing write buffer coherency: ok
[    0.042944] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.043004] Setting up static identity map for 0x4c4af8 - 0x4c4b50
[    0.043224] L310 cache controller enabled
[    0.043243] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[    0.121034] CPU1: Booted secondary processor
[    0.210228] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.210359] Brought up 2 CPUs
[    0.210378] SMP: Total of 2 processors activated.
[    0.210387] CPU: All CPU(s) started in SVC mode.
[    0.211050] devtmpfs: initialized
[    0.213466] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.214675] regulator-dummy: no parameters
[    0.221944] NET: Registered protocol family 16
[    0.224245] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.226515] cpuidle: using governor ladder
[    0.226528] cpuidle: using governor menu
[    0.233882] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[    0.235388] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.235402] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.235514] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xf0080000
[    0.257199] bio: create slab at 0
[    0.258616] vgaarb: loaded
[    0.259324] SCSI subsystem initialized
[    0.260322] usbcore: registered new interface driver usbfs
[    0.260504] usbcore: registered new interface driver hub
[    0.260728] usbcore: registered new device driver usb
[    0.261274] media: Linux media interface: v0.10
[    0.261433] Linux video capture interface: v2.00
[    0.261669] pps_core: LinuxPPS API ver. 1 registered
[    0.261681] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
[    0.261803] PTP clock support registered
[    0.262173] EDAC MC: Ver: 3.0.0
[    0.263220] Advanced Linux Sound Architecture Driver Initialized.
[    0.266057] DMA-API: preallocated 4096 debug entries
[    0.266070] DMA-API: debugging enabled by kernel config
[    0.266155] Switched to clocksource arm_global_timer
[    0.285968] NET: Registered protocol family 2
[    0.286694] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.286793] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.286951] TCP: Hash tables configured (established 8192 bind 8192)
[    0.287017] TCP: reno registered
[    0.287036] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.287085] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.287363] NET: Registered protocol family 1
[    0.287693] RPC: Registered named UNIX socket transport module.
[    0.287705] RPC: Registered udp transport module.
[    0.287713] RPC: Registered tcp transport module.
[    0.287722] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.287735] PCI: CLS 0 bytes, default 64
[    0.288173] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    0.290193] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.291574] bounce pool size: 64 pages
[    0.292461] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.292657] msgmni has been set to 1486
[    0.293434] io scheduler noop registered
[    0.293447] io scheduler deadline registered
[    0.293485] io scheduler cfq registered (default)
[    0.306308] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[    0.306328] dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[    0.428779] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[    1.001634] console [ttyPS0] enabled
[    1.005898] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to f0068000
[    1.013546] [drm] Initialized drm 1.1.0 20060810
[    1.030702] brd: module loaded
[    1.040054] loop: module loaded
[    1.049753] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[    1.055502] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[    1.063396] libphy: XEMACPS mii bus: probed
[    1.067858] ------------- phy_id = 0x3625e62
[    1.072577] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[    1.081201] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.087862] ehci-pci: EHCI PCI platform driver
[    1.095070] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[    1.101946] usbcore: registered new interface driver usb-storage
[    1.108831] mousedev: PS/2 mouse device common for all mice
[    1.114912] i2c /dev entries driver
[    1.121846] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[    1.127365] cpufreq_cpu0: failed to get cpu0 regulator: -19
[    1.133239] Xilinx Zynq CpuIdle Driver started
[    1.138123] sdhci: Secure Digital Host Controller Interface driver
[    1.144220] sdhci: Copyright(c) Pierre Ossman
[    1.148586] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.155357] mmc0: no vqmmc regulator found
[    1.159466] mmc0: no vmmc regulator found
[    1.196178] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[    1.204863] usbcore: registered new interface driver usbhid
[    1.210380] usbhid: USB HID core driver
[    1.215104] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[    1.221400] nand: Micron MT29F2G08ABAEAWP
[    1.225364] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[    1.231314] Bad block table found at page 131008, version 0x01
[    1.237544] Bad block table found at page 130944, version 0x01
[    1.243601] 3 ofpart partitions found on MTD device pl353-nand
[    1.249383] Creating 3 MTD partitions on "pl353-nand":
[    1.254472] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[    1.262521] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[    1.269835] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[    1.278775] TCP: cubic registered
[    1.282010] NET: Registered protocol family 17
[    1.286720] Registering SWP/SWPB emulation handler
[    1.292646] regulator-dummy: disabling
[    1.296988] UBI: attaching mtd1 to ubi0
[    1.826332] UBI: scanning is finished
[    1.838013] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[    1.845064] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    1.851861] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    1.858536] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[    1.865374] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[    1.871385] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[    1.878495] UBI: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 862493722
[    1.887438] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[    1.896654] UBI: background thread "ubi_bgt0d" started, PID 1080
[    1.896660] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    1.900591] ALSA device list:
[    1.900595]   No soundcards found.
[    1.917039] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082
[    1.973196] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[    1.979169] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    1.988271] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[    1.998148] UBIFS: reserved for root: 0 bytes (0 KiB)
[    2.003175] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 2A24A8E1-2021-4A54-8A4E-D8E294AE00E5, small LPT model
[    2.014490] VFS: Mounted root (ubifs filesystem) on device 0:11.
[    2.021518] devtmpfs: mounted
[    2.024621] Freeing unused kernel memory: 204K (c06d2000 - c0705000)
[    2.863644] random: dd urandom read with 0 bits of entropy available
[    3.256202]
[    3.256202] bcm54xx_config_init
[    3.866187]
[    3.866187] bcm54xx_config_init
[    7.867034] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[    7.873126] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[   22.543717] In axi fpga driver!
[   22.546809] request_mem_region OK!
[   22.550178] AXI fpga dev virtual address is 0xf01fe000
[   22.555284] *base_vir_addr = 0xc510
[   22.570491] In fpga mem driver!
[   22.573608] request_mem_region OK!
[   22.577231] fpga mem virtual address is 0xf3000000
[   23.366210]
[   23.366210] bcm54xx_config_init
[   23.996172]
[   23.996172] bcm54xx_config_init
[   27.997046] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[   28.003068] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[  235.493548] random: nonblocking pool is initialized
Detect 1GB control board of XILINX
Miner Type = T9+
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x0000ffff
chain[1] PIC jump to app
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[1]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[1]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[1]!
Check chain[1] PIC fw version=0xff
chain[1] PIC need restore ...
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[1]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[1]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[1]!
After restore: chain[1] PIC fw version=0xff
chain[1] PIC need restore ...
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[1]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[1]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[1]!
After restore: chain[1] PIC fw version=0xff
chain[2] PIC jump to app
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[2]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[2]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[2]!
Check chain[2] PIC fw version=0xff
chain[2] PIC need restore ...
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[2]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[2]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[2]!
After restore: chain[2] PIC fw version=0xff
chain[2] PIC need restore ...


here my friend , this is my log after your new bmminer designed to me.
Pages:
Bitcoin Forum>Bitcoin>Mining>Mining software (miners)
Jump to: