Topic: ¤¤¤¤ antrun.de - Antrouter R1 Fun-Run - compare your share ¤¤¤¤ - page 22. (Read 97868 times)
So,
like promised,
here some infos and a couple of first pics from my Peltier-cooled R1 Mod...
(Sorry, links only, but I hope, I get the Full member status asap, so I´m able to insert the pics directly)
What I´ve done with the R1 before:
1. disabled the internal power supply and using a Powerbrick with 5 Volt/10 Amp as supply
2. first trying to use heatsinks on both sides of BM1384, but decided finally to reuse the original case, because it´s in my eyes a good solution for heat dissipation
3. using twice new cooling pads on each sides of internal BM1384 for more pressure and better cooling conditions!
4. Vcore Mod with pot for variable VCore between 0.6 up to 1V
5. adding a Vcore voltmeter
6. add an Sharkoon HPS1
7. add an Peltier solution
But here finally some pics
:
1. Sharkoon HPS1 Cooler stuffed with a 40x40 Peltier
2. Sharkoon HPS1 Cooler with Peltier saddled up on the R1 Mod
3. First try - in front the Peltier-Controller Board
4. First working Temp Measure: note(!) In=Ambient Temp 25.1C , and OUT=Minertemp! = 24,9C
5. First test @300MHz / Vcore 0.724 Volt
6. Second test @475MHz / Vcore 0.891 Volt working Temp Measure: In=Ambient Temp 24.7C (opened Window) and OUT = Minertemp=41,1C
7. Third test @475MHz / screwed up Vcore to 0.900 Volt
8. Closer look @R1 running on 475Mhz
9. Screenshot of my Power Measuring Software - Consumption between 25 and 27 Watts @475MHz
Update: added a Test-Screenshot after 26min of running my R1 @25-27GHs (06.05.2016)
10. R1@475MHz Average 25-27GHs
Thats it for now
If any questions, feel free to ask me.
andY
like promised,
here some infos and a couple of first pics from my Peltier-cooled R1 Mod...
(Sorry, links only, but I hope, I get the Full member status asap, so I´m able to insert the pics directly)
What I´ve done with the R1 before:
1. disabled the internal power supply and using a Powerbrick with 5 Volt/10 Amp as supply
2. first trying to use heatsinks on both sides of BM1384, but decided finally to reuse the original case, because it´s in my eyes a good solution for heat dissipation
3. using twice new cooling pads on each sides of internal BM1384 for more pressure and better cooling conditions!
4. Vcore Mod with pot for variable VCore between 0.6 up to 1V
5. adding a Vcore voltmeter
6. add an Sharkoon HPS1
7. add an Peltier solution
But here finally some pics
:1. Sharkoon HPS1 Cooler stuffed with a 40x40 Peltier
2. Sharkoon HPS1 Cooler with Peltier saddled up on the R1 Mod
3. First try - in front the Peltier-Controller Board
4. First working Temp Measure: note(!) In=Ambient Temp 25.1C , and OUT=Minertemp! = 24,9C
5. First test @300MHz / Vcore 0.724 Volt
6. Second test @475MHz / Vcore 0.891 Volt working Temp Measure: In=Ambient Temp 24.7C (opened Window
) and OUT = Minertemp=41,1C7. Third test @475MHz / screwed up Vcore to 0.900 Volt
8. Closer look @R1 running on 475Mhz
9. Screenshot of my Power Measuring Software - Consumption between 25 and 27 Watts @475MHz
Update: added a Test-Screenshot after 26min of running my R1 @25-27GHs (06.05.2016)
10. R1@475MHz Average 25-27GHs
Thats it for now
If any questions, feel free to ask me.
andY
@Rich: Your second R1 is very lonely at the bottom of the list! 
My R1 is with him to hold his hand on Position 24 
Hi ammi,
is it possible, to expand the antrun.de MHz-Range to 500MHz?
I got my first successfully working tests @475MHz / 462.5MHz.
It´s now possible with a special selfmade Peltier-Cooling solution)
Thx,
andY
is it possible, to expand the antrun.de MHz-Range to 500MHz?
I got my first successfully working tests @475MHz / 462.5MHz
.It´s now possible with a special selfmade Peltier-Cooling solution
) Thx,
andY
Nice Frequencies. I am playing with my gekko at the moment, have done brief tests at 400MHz, but a few HW errors so need to do a mod to up the voltage as have run out of range on the pot.
Good Luck...
Rich
!@Gekko VCore : I guess the value for the pulldown resistor to Ground is too high....?
For my R1 I used a 10k to ground from the pot, so its possible a max Vcore of nearly 1V.
@Nice frequencies: yes, I think its not bad for the beginning
But the major issue seems to be the ckpool, so very often I got stops there between 10 to 30 minutes
@Minibit:
Hi ammi,
is it possible, to expand the antrun.de MHz-Range to 500MHz?
I got my first successfully working tests @475MHz / 462.5MHz.
It´s now possible with a special selfmade Peltier-Cooling solution)
Thx,
andY
is it possible, to expand the antrun.de MHz-Range to 500MHz?
I got my first successfully working tests @475MHz / 462.5MHz
.It´s now possible with a special selfmade Peltier-Cooling solution
) Thx,
andY
Can you post a picture of your R1? Cooling with Peltier sounds nice!
Yes, no prob, I´ll upload it asap
.But don´t be disappointed, it´s a first "quick´n´dirty" solution for testing
And unfortunately, as still a newbie status member here, It´s forbidden to post embedded pictures, only picture links are possible
andY
@Rich: Your second R1 is very lonely at the bottom of the list!
Unfortunately it is dead.... and should, be put to rest. It is now just being used to control one of my gekko Miners, so not all is lost.
Rich
Hi ammi,
is it possible, to expand the antrun.de MHz-Range to 500MHz?
I got my first successfully working tests @475MHz / 462.5MHz.
It´s now possible with a special selfmade Peltier-Cooling solution)
Thx,
andY
is it possible, to expand the antrun.de MHz-Range to 500MHz?
I got my first successfully working tests @475MHz / 462.5MHz
.It´s now possible with a special selfmade Peltier-Cooling solution
) Thx,
andY
Can you post a picture of your R1? Cooling with Peltier sounds nice!
@Rich: Your second R1 is very lonely at the bottom of the list!
Hi ammi,
is it possible, to expand the antrun.de MHz-Range to 500MHz?
I got my first successfully working tests @475MHz / 462.5MHz.
It´s now possible with a special selfmade Peltier-Cooling solution)
Thx,
andY
is it possible, to expand the antrun.de MHz-Range to 500MHz?
I got my first successfully working tests @475MHz / 462.5MHz
.It´s now possible with a special selfmade Peltier-Cooling solution
) Thx,
andY
Nice Frequencies. I am playing with my gekko at the moment, have done brief tests at 400MHz, but a few HW errors so need to do a mod to up the voltage as have run out of range on the pot.
Good Luck...
Rich
Hi ammi,
is it possible, to expand the antrun.de MHz-Range to 500MHz?
I got my first successfully working tests @475MHz / 462.5MHz.
It´s now possible with a special selfmade Peltier-Cooling solution)
Thx,
andY
is it possible, to expand the antrun.de MHz-Range to 500MHz?
I got my first successfully working tests @475MHz / 462.5MHz
.It´s now possible with a special selfmade Peltier-Cooling solution
) Thx,
andY
Gold again 
Woo, new bestever share of 2.3M, I get a ribbon for a little while! 
Right now my R1 is actually even beating my compac which has 3+ times the hash power.
Right now my R1 is actually even beating my compac which has 3+ times the hash power.
My antrouter hasn't arrived yet XD
Ahhhh.... welcome to the fun race!
My antrouter hasn't arrived yet XD
If any of us mine a block it will make bitcoin history, lets let it be me
Want to see CK posting the log, possible block solve diff XXXXXX and my antrouter worker, come on my beauty! Will set it up when it comes and let it mine that block for me
this is just a bit of fun XD
My antrouter will crush all others! whahahahaha
Want to see CK posting the log, possible block solve diff XXXXXX and my antrouter worker, come on my beauty! Will set it up when it comes and let it mine that block for me
this is just a bit of fun XD
My antrouter will crush all others! whahahahaha
LOL... whats your worker's name, I dont see it in the table... watch out tiny island racer coming up your lane now....
If any of us mine a block it will make bitcoin history, lets let it be me
Want to see CK posting the log, possible block solve diff XXXXXX and my antrouter worker, come on my beauty! Will set it up when it comes and let it mine that block for me
this is just a bit of fun XD
My antrouter will crush all others! whahahahaha
Want to see CK posting the log, possible block solve diff XXXXXX and my antrouter worker, come on my beauty! Will set it up when it comes and let it mine that block for me
this is just a bit of fun XD
My antrouter will crush all others! whahahahaha
Hello fellow antrunners,
we proudly announce the first official Logo-Contest
https://bitcointalksearch.org/topic/antrunde-gekkorunde-logo-contest-win-up-to-02-btc-1460323
We will be happy to see your creativity
Have fun and race on
ammi & minibit
Source got switched to "last 5 minutes"
Page is updated & online
Page is updated & online
sounds good
let's switch to 5 minutes :-)
let's switch to 5 minutes :-)
I think rich is right -- people are still finetuning their R1s and in that 1min brackets you will see weird hash like 100mhs or 100ghs.... my racer posted 111GHs this very moment, I don't know why.
sounds good
let's switch to 5 minutes :-)
let's switch to 5 minutes :-)
Does anybody know what is causing these extreme spikes in the hashrate? Are they legit?
Would it be better, if we switch to "hashrate5m" instead of "hashrate1m"?
Edit: I'm talking about the chart at the front pages of Antrun and Gekkorun, not the individual racer stats...
Would it be better, if we switch to "hashrate5m" instead of "hashrate1m"?
Edit: I'm talking about the chart at the front pages of Antrun and Gekkorun, not the individual racer stats...
I suspect 1 Minute is just too short a sample period and exposed to the timing of and number of shares that happen to be submitted in the period. I think 5 Minute would be better.
Rich
Does anybody know what is causing these extreme spikes in the hashrate? Are they legit?
Would it be better, if we switch to "hashrate5m" instead of "hashrate1m"?
Edit: I'm talking about the chart at the front pages of Antrun and Gekkorun, not the individual racer stats...
Would it be better, if we switch to "hashrate5m" instead of "hashrate1m"?
Edit: I'm talking about the chart at the front pages of Antrun and Gekkorun, not the individual racer stats...
Jump to: