Topic: ASICPuppy.net - Terminus, Moonlander 2, 2pacs in Stock! BTC,LTC,ETH,BCH - page 21. (Read 105431 times)
September 06, 2014, 12:09:41 PM
I bought my second set of Am v2 and I am having no luck with it hashing past 310gh. I have tried taking all wires off and reconnecting and no luck. I also am not able to get it noticed by the rasp Pi as a 3rd and 4th blade as it says it can be. I was not shipped a rasp Pi cable with this miner also so that I can run it with a 2nd rasp instead of the same. I'm hoping that I can get this resolved quickly as I am losing much mining time and the prices just dropped dramatically the day after I bought them. Please PM me and help me out.
September 06, 2014, 11:14:03 AM
Hi all. wow great rig set ups you guys have. I'm still a bit new to mining. and just ordered one of those Blackarrow breakout boards. and i'll have a total of 5 r-boxes monday.
I'm going to be using a Corsair CX 500 watt modular PSU.
and before i go plugging cables into that board i just have a few questions.
1) in order to run the 5 r-boxes, do i plug the 24 pin ATX cable and the 8 pin CPU and one of the 8 pin PCIe cables into the board and then attach my r-box pigtails to thier respective + and - connections on the board ?
2) and if and when i eventually have all 10 r-boxes ( if i can find 5 more over the next couple of months ) do i need to plug the last 8 pin PCIe in for them or will what i have plugged in be enough ?
3) How would i go about plugging my Raspberry Pi Model B+ onto that breakout board? i can't seen to find any pictures of that set up anywhere.
4) i have a Rosewill 7 port USB hub which i'll have to upgrade to a 10 Port when i get all 10 R-boxes. Is there a way to power that off the Breakout board or will that still need to be plugged into a powerstrip ?
any answers to these questions is appreciated. been learning quite a lot from reading these forums. you guys are great
Thanks
I'm going to be using a Corsair CX 500 watt modular PSU.
and before i go plugging cables into that board i just have a few questions.
1) in order to run the 5 r-boxes, do i plug the 24 pin ATX cable and the 8 pin CPU and one of the 8 pin PCIe cables into the board and then attach my r-box pigtails to thier respective + and - connections on the board ?
2) and if and when i eventually have all 10 r-boxes ( if i can find 5 more over the next couple of months ) do i need to plug the last 8 pin PCIe in for them or will what i have plugged in be enough ?
3) How would i go about plugging my Raspberry Pi Model B+ onto that breakout board? i can't seen to find any pictures of that set up anywhere.
4) i have a Rosewill 7 port USB hub which i'll have to upgrade to a 10 Port when i get all 10 R-boxes. Is there a way to power that off the Breakout board or will that still need to be plugged into a powerstrip ?
any answers to these questions is appreciated. been learning quite a lot from reading these forums. you guys are great
Thanks
plug the 24 pin atx c able
plug both pcie cables
leave the cpu cable out
if I recall you can get 5 volt power out of that but I never bothered to do it.
see photo bottom right just above the on off there is a none wired 3 volt and right above it a 5 volt that is ready for use it has 4 screws on it. 2 pos 2 neg check your wiring very carefully when you hook your gear up.
Yes you can power your R-Pi off the 5v output on the BA board. I will post pics later.
September 06, 2014, 08:01:30 AM
Hi all. wow great rig set ups you guys have. I'm still a bit new to mining. and just ordered one of those Blackarrow breakout boards. and i'll have a total of 5 r-boxes monday.
I'm going to be using a Corsair CX 500 watt modular PSU.
and before i go plugging cables into that board i just have a few questions.
1) in order to run the 5 r-boxes, do i plug the 24 pin ATX cable and the 8 pin CPU and one of the 8 pin PCIe cables into the board and then attach my r-box pigtails to thier respective + and - connections on the board ?
2) and if and when i eventually have all 10 r-boxes ( if i can find 5 more over the next couple of months ) do i need to plug the last 8 pin PCIe in for them or will what i have plugged in be enough ?
3) How would i go about plugging my Raspberry Pi Model B+ onto that breakout board? i can't seen to find any pictures of that set up anywhere.
4) i have a Rosewill 7 port USB hub which i'll have to upgrade to a 10 Port when i get all 10 R-boxes. Is there a way to power that off the Breakout board or will that still need to be plugged into a powerstrip ?
any answers to these questions is appreciated. been learning quite a lot from reading these forums. you guys are great
Thanks
I'm going to be using a Corsair CX 500 watt modular PSU.
and before i go plugging cables into that board i just have a few questions.
1) in order to run the 5 r-boxes, do i plug the 24 pin ATX cable and the 8 pin CPU and one of the 8 pin PCIe cables into the board and then attach my r-box pigtails to thier respective + and - connections on the board ?
2) and if and when i eventually have all 10 r-boxes ( if i can find 5 more over the next couple of months ) do i need to plug the last 8 pin PCIe in for them or will what i have plugged in be enough ?
3) How would i go about plugging my Raspberry Pi Model B+ onto that breakout board? i can't seen to find any pictures of that set up anywhere.
4) i have a Rosewill 7 port USB hub which i'll have to upgrade to a 10 Port when i get all 10 R-boxes. Is there a way to power that off the Breakout board or will that still need to be plugged into a powerstrip ?
any answers to these questions is appreciated. been learning quite a lot from reading these forums. you guys are great
Thanks
plug the 24 pin atx c able
plug both pcie cables
leave the cpu cable out
if I recall you can get 5 volt power out of that but I never bothered to do it.
see photo bottom right just above the on off there is a none wired 3 volt and right above it a 5 volt that is ready for use it has 4 screws on it. 2 pos 2 neg check your wiring very carefully when you hook your gear up.
September 06, 2014, 12:46:55 AM
Hi all. wow great rig set ups you guys have. I'm still a bit new to mining. and just ordered one of those Blackarrow breakout boards. and i'll have a total of 5 r-boxes monday.
I'm going to be using a Corsair CX 500 watt modular PSU.
and before i go plugging cables into that board i just have a few questions.
1) in order to run the 5 r-boxes, do i plug the 24 pin ATX cable and the 8 pin CPU and one of the 8 pin PCIe cables into the board and then attach my r-box pigtails to thier respective + and - connections on the board ?
2) and if and when i eventually have all 10 r-boxes ( if i can find 5 more over the next couple of months ) do i need to plug the last 8 pin PCIe in for them or will what i have plugged in be enough ?
3) How would i go about plugging my Raspberry Pi Model B+ onto that breakout board? i can't seen to find any pictures of that set up anywhere.
4) i have a Rosewill 7 port USB hub which i'll have to upgrade to a 10 Port when i get all 10 R-boxes. Is there a way to power that off the Breakout board or will that still need to be plugged into a powerstrip ?
any answers to these questions is appreciated. been learning quite a lot from reading these forums. you guys are great
Thanks
I'm going to be using a Corsair CX 500 watt modular PSU.
and before i go plugging cables into that board i just have a few questions.
1) in order to run the 5 r-boxes, do i plug the 24 pin ATX cable and the 8 pin CPU and one of the 8 pin PCIe cables into the board and then attach my r-box pigtails to thier respective + and - connections on the board ?
2) and if and when i eventually have all 10 r-boxes ( if i can find 5 more over the next couple of months ) do i need to plug the last 8 pin PCIe in for them or will what i have plugged in be enough ?
3) How would i go about plugging my Raspberry Pi Model B+ onto that breakout board? i can't seen to find any pictures of that set up anywhere.
4) i have a Rosewill 7 port USB hub which i'll have to upgrade to a 10 Port when i get all 10 R-boxes. Is there a way to power that off the Breakout board or will that still need to be plugged into a powerstrip ?
any answers to these questions is appreciated. been learning quite a lot from reading these forums. you guys are great
Thanks
September 05, 2014, 06:45:16 PM
Fully Assembled ASICMiner Tubes are in stock and ready to ship. AntMiner PSU jumper switches also in stock. Free AntMiner Jumper switch with each order of 400gh/s or more for a limited time.
How much for one inc. shipping to the UK,and how long should it take to get here?
Shipping price is calculated at checkout. For international orders I use USPS priority international.
September 05, 2014, 03:36:53 AM
Fully Assembled ASICMiner Tubes are in stock and ready to ship. AntMiner PSU jumper switches also in stock. Free AntMiner Jumper switch with each order of 400gh/s or more for a limited time.
How much for one inc. shipping to the UK,and how long should it take to get here?
September 04, 2014, 10:11:38 PM
Fully Assembled ASICMiner Tubes are in stock and ready to ship. AntMiner PSU jumper switches also in stock. Free AntMiner Jumper switch with each order of 400gh/s or more for a limited time.
September 02, 2014, 07:41:18 AM
Crazy Guy is the bomb:)
September 01, 2014, 12:39:26 PM
Done and thanks:) I was hoping to get faster shipping being a repeat customer:) I will await the miner!
September 01, 2014, 12:22:40 PM
Free shipping is not working on the site and I was trying to order.
I lowered the unit price bur didn't update the free shipping threshold. Free shipping option is now enabled for purchases of two or more units. Try again.
September 01, 2014, 12:16:39 PM
Free shipping is not working on the site and I was trying to order.
August 31, 2014, 09:16:49 PM
Free shipping promotion continued through Labor day.
August 28, 2014, 09:17:33 PM
Free Shipping Promotion running through Sunday! Orders of 2 or more AMV1 X2 units will have the option of free standard shipping.
August 24, 2014, 09:53:45 AM
AMV1X2 has been reduced to $439.99
August 17, 2014, 08:56:07 AM
Prices lowered
AMV1X2 - $499.99.
S3 - $469.99
AMV1X2 - $499.99.
S3 - $469.99
August 13, 2014, 12:44:22 AM
I just received a stack of cardboard boxes that can hold 4 X2 units. At 30x30x12, they are just over the size accepted for USPS priority. However, if you are willing to wait 5-6 days parcel post, I can ship for $14 per unit with an order of 4. For those interested, please contact me via PM.
Good looking out bro!
I got some pics for ya too...I'll have them to ya first thing tomorrow. Also made the final changes to the combo case and will be printing those starting asap (1 ASICPuppy lid done!)
August 12, 2014, 09:09:09 PM
I just received a stack of cardboard boxes that can hold 4 X2 units. At 30x30x12, they are just over the size accepted for USPS priority. However, if you are willing to wait 5-6 days parcel post, I can ship for $14 per unit with an order of 4. For those interested, please contact me via PM.
August 11, 2014, 01:58:00 PM
X2s have arrived. All orders placed by by 3pm CST will be shipped today.
August 08, 2014, 08:11:53 PM
X2s have arrived in the US and barring any customs delays, they should be delivered Monday.
August 06, 2014, 10:36:49 PM
RBox units are now out of stock.
Jump to: