Can't help with firmware, mine came with a reset button and firmware 12.12.2013.
Haven't seen anything that indicates these are better with the newer firmware.
Topic: [Auction] BITMAIN launch first batch AntMiner S1-180GH/s 360W on wall (Read 20828 times)
January 20, 2014, 07:48:04 PM
January 19, 2014, 08:13:09 PM
Before you received the goods, you want to read this carefully. If you have any questions, please ask.
First, you have to connect your computer and the miner directly with an Ethernet cable. Then you manually set your IP address at 192.168.2.XXX, so you can browse the control panel. This is very similar to other OpenWRT based miners.
Default user name and password: root / root.
Please check the LAN setting before you change the WAN ip address. You should change the LAN into “DHCP client” mode, and click “Switch Protocol” then click “Save and apply”. Make sure the LAN interface is really in DHCP client mode. Then you can change WAN interface IP address according to your local network settings. The LAN is useless for users, but only useful to developers. If you do not follow this, and set LAN and WAN’s IP address at the same subset, you will not be able to log into the control panel again.
Don’t forget the WAN IP address you have set up. If you forget, you will not be able to login into the miner.
First, you have to connect your computer and the miner directly with an Ethernet cable. Then you manually set your IP address at 192.168.2.XXX, so you can browse the control panel. This is very similar to other OpenWRT based miners.
Default user name and password: root / root.
Please check the LAN setting before you change the WAN ip address. You should change the LAN into “DHCP client” mode, and click “Switch Protocol” then click “Save and apply”. Make sure the LAN interface is really in DHCP client mode. Then you can change WAN interface IP address according to your local network settings. The LAN is useless for users, but only useful to developers. If you do not follow this, and set LAN and WAN’s IP address at the same subset, you will not be able to log into the control panel again.
Don’t forget the WAN IP address you have set up. If you forget, you will not be able to login into the miner.
No reset to factory settings?
No, there is not in this version of control board. That's why I posted here. Please use labels and notes.
Please do not forget the login password if you change it.
And if that happens where can one get a new bitmaintech v1.2 comm board? I may have a little problem..
https://github.com/AntMiner/AntGen1/tree/master/manual
AntMiner FAQ pdf has instructions on how to jump two connections for a factory reset. Note the IP will change as documented in that FAQ.
OK that worked, I just needed to hookup miner with LAN , set my laptop IP to 192.168.2.x or 192.168.1.x and ping in CMD window. I got 2 of them miners and after reset one was 192.168.1.99 and the other was after resets 192.168.2.99. But it would be nice to see spare parts on Ebay or AliExpress in case something was really damaged.
Any idea how to upgrade to the best cgminer for this miner? I got different versions in each one.
cgminer V3.4.3-1 and the other one has cgminer V3.8.5-1
January 19, 2014, 11:27:01 AM
Before you received the goods, you want to read this carefully. If you have any questions, please ask.
First, you have to connect your computer and the miner directly with an Ethernet cable. Then you manually set your IP address at 192.168.2.XXX, so you can browse the control panel. This is very similar to other OpenWRT based miners.
Default user name and password: root / root.
Please check the LAN setting before you change the WAN ip address. You should change the LAN into “DHCP client” mode, and click “Switch Protocol” then click “Save and apply”. Make sure the LAN interface is really in DHCP client mode. Then you can change WAN interface IP address according to your local network settings. The LAN is useless for users, but only useful to developers. If you do not follow this, and set LAN and WAN’s IP address at the same subset, you will not be able to log into the control panel again.
Don’t forget the WAN IP address you have set up. If you forget, you will not be able to login into the miner.
First, you have to connect your computer and the miner directly with an Ethernet cable. Then you manually set your IP address at 192.168.2.XXX, so you can browse the control panel. This is very similar to other OpenWRT based miners.
Default user name and password: root / root.
Please check the LAN setting before you change the WAN ip address. You should change the LAN into “DHCP client” mode, and click “Switch Protocol” then click “Save and apply”. Make sure the LAN interface is really in DHCP client mode. Then you can change WAN interface IP address according to your local network settings. The LAN is useless for users, but only useful to developers. If you do not follow this, and set LAN and WAN’s IP address at the same subset, you will not be able to log into the control panel again.
Don’t forget the WAN IP address you have set up. If you forget, you will not be able to login into the miner.
No reset to factory settings?
No, there is not in this version of control board. That's why I posted here. Please use labels and notes.
Please do not forget the login password if you change it.
And if that happens where can one get a new bitmaintech v1.2 comm board? I may have a little problem..
https://github.com/AntMiner/AntGen1/tree/master/manual
AntMiner FAQ pdf has instructions on how to jump two connections for a factory reset. Note the IP will change as documented in that FAQ.
January 18, 2014, 08:49:45 PM
Before you received the goods, you want to read this carefully. If you have any questions, please ask.
First, you have to connect your computer and the miner directly with an Ethernet cable. Then you manually set your IP address at 192.168.2.XXX, so you can browse the control panel. This is very similar to other OpenWRT based miners.
Default user name and password: root / root.
Please check the LAN setting before you change the WAN ip address. You should change the LAN into “DHCP client” mode, and click “Switch Protocol” then click “Save and apply”. Make sure the LAN interface is really in DHCP client mode. Then you can change WAN interface IP address according to your local network settings. The LAN is useless for users, but only useful to developers. If you do not follow this, and set LAN and WAN’s IP address at the same subset, you will not be able to log into the control panel again.
Don’t forget the WAN IP address you have set up. If you forget, you will not be able to login into the miner.
First, you have to connect your computer and the miner directly with an Ethernet cable. Then you manually set your IP address at 192.168.2.XXX, so you can browse the control panel. This is very similar to other OpenWRT based miners.
Default user name and password: root / root.
Please check the LAN setting before you change the WAN ip address. You should change the LAN into “DHCP client” mode, and click “Switch Protocol” then click “Save and apply”. Make sure the LAN interface is really in DHCP client mode. Then you can change WAN interface IP address according to your local network settings. The LAN is useless for users, but only useful to developers. If you do not follow this, and set LAN and WAN’s IP address at the same subset, you will not be able to log into the control panel again.
Don’t forget the WAN IP address you have set up. If you forget, you will not be able to login into the miner.
No reset to factory settings?
No, there is not in this version of control board. That's why I posted here. Please use labels and notes.
Please do not forget the login password if you change it.
And if that happens where can one get a new bitmaintech v1.2 comm board? I may have a little problem..
December 15, 2013, 03:08:30 AM
Thanks a lot novymivo, it worked! A lot easier than expected. 
December 15, 2013, 12:24:20 AM
You should change the LAN into “DHCP client” mode
Does this have to be changed? or can it be left at 192.168.2.xxx?
I don't have DHCP server running on my router.
LAN is useless for the users, so you don't need worry about that.
it would be nice to see a step-by-step with a few pictures to make the process more fool-proof.
coming soon
Yes, but it will be mission impossible for average users to do this. In China we already have two buyers suffered this, and we have to ship them a new control board.
Bitmain,
My machine is locked. No mining done. Can you please send a new control board asap or recommend best resolution. Do not know best practice to short...otherwise need technical assistance to short.
Thank you,
JK
try this :
https://github.com/AntMiner/AntGen1/blob/master/manual/AntMiner%20FAQ.pdf
I read that but wondering about the following step 3 in the FAQ:
"Step3: Short the RESET PIN to 3.3V as the following picture for more than 3 seconds"
Is this 3.3V reset done with a simple jumper wire touching these two points for 3-5 sec? Guess I a bit concerned about the "3.3V" and needing to adjust voltage, etc....thanks!
use wire to connect them for 5 sec .
December 15, 2013, 12:00:33 AM
You should change the LAN into “DHCP client” mode
Does this have to be changed? or can it be left at 192.168.2.xxx?
I don't have DHCP server running on my router.
LAN is useless for the users, so you don't need worry about that.
it would be nice to see a step-by-step with a few pictures to make the process more fool-proof.
coming soon
Yes, but it will be mission impossible for average users to do this. In China we already have two buyers suffered this, and we have to ship them a new control board.
Bitmain,
My machine is locked. No mining done. Can you please send a new control board asap or recommend best resolution. Do not know best practice to short...otherwise need technical assistance to short.
Thank you,
JK
try this :
https://github.com/AntMiner/AntGen1/blob/master/manual/AntMiner%20FAQ.pdf
I read that but wondering about the following step 3 in the FAQ:
"Step3: Short the RESET PIN to 3.3V as the following picture for more than 3 seconds"
Is this 3.3V reset done with a simple jumper wire touching these two points for 3-5 sec? Guess I a bit concerned about the "3.3V" and needing to adjust voltage, etc....thanks!
December 14, 2013, 09:17:33 PM
You should change the LAN into “DHCP client” mode
Does this have to be changed? or can it be left at 192.168.2.xxx?
I don't have DHCP server running on my router.
LAN is useless for the users, so you don't need worry about that.
it would be nice to see a step-by-step with a few pictures to make the process more fool-proof.
coming soon
Yes, but it will be mission impossible for average users to do this. In China we already have two buyers suffered this, and we have to ship them a new control board.
Bitmain,
My machine is locked. No mining done. Can you please send a new control board asap or recommend best resolution. Do not know best practice to short...otherwise need technical assistance to short.
Thank you,
JK
try this :
https://github.com/AntMiner/AntGen1/blob/master/manual/AntMiner%20FAQ.pdf
December 14, 2013, 01:15:33 PM
You should change the LAN into “DHCP client” mode
Does this have to be changed? or can it be left at 192.168.2.xxx?
I don't have DHCP server running on my router.
LAN is useless for the users, so you don't need worry about that.
it would be nice to see a step-by-step with a few pictures to make the process more fool-proof.
coming soon
Yes, but it will be mission impossible for average users to do this. In China we already have two buyers suffered this, and we have to ship them a new control board.
Bitmain,
My machine is locked. No mining done. Can you please send a new control board asap or recommend best resolution. Do not know best practice to short...otherwise need technical assistance to short.
Thank you,
JK
November 28, 2013, 05:06:32 PM
Many thanks Goxed, you have put my fears about the hardware to rest with the shot of your pool stats
Cool November 28, 2013, 12:19:56 PM
Many thanks Goxed, you have put my fears about the hardware to rest with the shot of your pool stats
November 28, 2013, 06:11:25 AM
up & running @178GHash in p2pool (many miners perform a little bit worse in this) so I'm happy with this performance
stable wifi connection established
stable wifi connection established
How about a screenshot?
Make a lot of us feel better.
http://www.bilder-upload.eu/show.php?file=663597-1385421452.png
Can you tell us what the rate of share delivery is to the pool?
Your image has
Elapsed 1h 3m 57s
Accepted 257
Rejected 162
Discard 508
HW 148
Am I just reading this wrong, are the figures in a different scale or is that really 257 shares accepted after 1 hours mining?
November 28, 2013, 06:08:13 AM
up & running @178GHash in p2pool (many miners perform a little bit worse in this) so I'm happy with this performance
stable wifi connection established
stable wifi connection established
How about a screenshot?
Make a lot of us feel better.
http://www.bilder-upload.eu/show.php?file=663597-1385421452.png
Can you tell us what the rate of share delivery is to the pool?
Your image has
Elapsed 1h 3m 57s
Accepted 257
Rejected 162
Discard 508
HW 148
Am I just reading this wrong, are the figures in a different scale or is that really 257 shares accepted after 1 hours mining?
November 28, 2013, 02:23:50 AM
up & running @178GHash in p2pool (many miners perform a little bit worse in this) so I'm happy with this performance
stable wifi connection established
stable wifi connection established
How about a screenshot?
Make a lot of us feel better.
http://www.bilder-upload.eu/show.php?file=663597-1385421452.png
Can you tell us what the rate of share delivery is to the pool?
Your image has
Elapsed 1h 3m 57s
Accepted 257
Rejected 162
Discard 508
HW 148
Am I just reading this wrong, are the figures in a different scale or is that really 257 shares accepted after 1 hours mining?
November 27, 2013, 09:40:50 PM
November 27, 2013, 09:38:01 PM
Thanks unit arrived on time.
November 26, 2013, 12:49:58 PM
AntMiner does not connect to eligius - status: dead
AntMiner is doing you a favor. It is a next-gen device and knows better than to mine at Eligius and support Luke-Jrs shenanigans.
Guys,
have a go at HHTT, it should work out-of-the-box.
spiccioli
November 26, 2013, 12:06:59 PM
thanks mate, appreciate the feedback!
Hi everyone I have got mine rig and connet it use MEANWELL swith power. This kind of power normally been used at Automation part. But in this case it running well. Just noise bigger than ATX power. The price about 70USD. Followed picture is connected miner.
I have some big trouble at first started miner. Always no any hashrate. Luckly today ANTMINER engineer use teamviwer help me solved problem.The problem is maybe because of my internet envirment issue miner can not find NTPD server so cgminer stuck at there. So maybe another miner also stuck at this problem so I write down ANTMINER engineer suggest how to solve this problem:
（1）modify /etc/resolv.conf,change 'nameserver' setup to DMS
（2）commet ntpd out of /etc/init.d/cgminer
（3）reboot
This is now miner running speed realiable around 180G.
I really like this miner noise lower and until now work realiable espencially have good service form supplier.
Hope this can give your help. Happy mining
I have some big trouble at first started miner. Always no any hashrate. Luckly today ANTMINER engineer use teamviwer help me solved problem.The problem is maybe because of my internet envirment issue miner can not find NTPD server so cgminer stuck at there. So maybe another miner also stuck at this problem so I write down ANTMINER engineer suggest how to solve this problem:
（1）modify /etc/resolv.conf,change 'nameserver' setup to DMS
（2）commet ntpd out of /etc/init.d/cgminer
（3）reboot
This is now miner running speed realiable around 180G.
I really like this miner noise lower and until now work realiable espencially have good service form supplier.
Hope this can give your help. Happy mining
November 26, 2013, 12:03:13 PM
Hi everyone I have got mine rig and connet it use MEANWELL swith power. This kind of power normally been used at Automation part. But in this case it running well. Just noise bigger than ATX power. The price about 70USD. Followed picture is connected miner.
I have some big trouble at first started miner. Always no any hashrate. Luckly today ANTMINER engineer use teamviwer help me solved problem.The problem is maybe because of my internet envirment issue miner can not find NTPD server so cgminer stuck at there. So maybe another miner also stuck at this problem so I write down ANTMINER engineer suggest how to solve this problem:
（1）modify /etc/resolv.conf,change 'nameserver' setup to DMS
（2）commet ntpd out of /etc/init.d/cgminer
（3）reboot
This is now miner running speed realiable around 180G.
I really like this miner noise lower and until now work realiable espencially have good service form supplier.
Hope this can give your help. Happy mining
I have some big trouble at first started miner. Always no any hashrate. Luckly today ANTMINER engineer use teamviwer help me solved problem.The problem is maybe because of my internet envirment issue miner can not find NTPD server so cgminer stuck at there. So maybe another miner also stuck at this problem so I write down ANTMINER engineer suggest how to solve this problem:
（1）modify /etc/resolv.conf,change 'nameserver' setup to DMS
（2）commet ntpd out of /etc/init.d/cgminer
（3）reboot
This is now miner running speed realiable around 180G.
I really like this miner noise lower and until now work realiable espencially have good service form supplier.
Hope this can give your help. Happy mining
November 26, 2013, 10:05:18 AM
AntMiner does not connect to eligius - status: dead
AntMiner is doing you a favor. It is a next-gen device and knows better than to mine at Eligius and support Luke-Jrs shenanigans.
I'm not a fan of him, but it's a solid pool (normaly actually it was ddosed;) good as backup
But I don't like btcguild and my favorite p2pool doesnt work proper
Jump to: