Is the official firmware?
How I can install it
How I can install it
https://bitcointalksearch.org/topic/m.3415231
https://www.asic-hardware.com/assembly-instructions-part-2/
Topic: BITBURNER FURY Technical discussion - page 5. (Read 18317 times)
https://bitcointalksearch.org/topic/m.3415231
https://www.asic-hardware.com/assembly-instructions-part-2/
HW-Error Rate is: 3.87
Where can i find this info in cgminer screen?calculate it...
(100/accepted shares)*HW
I got another 8-board stack yesterday.
This one also crashes my raspberry pis! Why does this happen? Does it happen to anybody else? Maybe I shouldn't be using Raspbian?? What installations do other people use?
My other 8-board stack is running off of a linux PC and it never crashes. I'd rather use raspbery pis though to save electricity.
As I mentioned before, I'd tried 2 different pis, with 2 different installations, 2 different versions of raspbian, two different power supplies, two different USB hubs (both powered), both wired and wifi internet, and the pi will still (eventually) freeze up after running for a while.
I have several other miners running off of raspberry pis (raspbian with cgminer) from BFL and they never crash. It's something about this special cgminer maybe or just the hardware? I don't really get it.
This one also crashes my raspberry pis! Why does this happen? Does it happen to anybody else? Maybe I shouldn't be using Raspbian?? What installations do other people use?
My other 8-board stack is running off of a linux PC and it never crashes. I'd rather use raspbery pis though to save electricity.
As I mentioned before, I'd tried 2 different pis, with 2 different installations, 2 different versions of raspbian, two different power supplies, two different USB hubs (both powered), both wired and wifi internet, and the pi will still (eventually) freeze up after running for a while.
I have several other miners running off of raspberry pis (raspbian with cgminer) from BFL and they never crash. It's something about this special cgminer maybe or just the hardware? I don't really get it.
Hi,
Referring to order no:1509, upon receiving my 3 bitburner fury boards,1 of the boards does not power up/malfunction. Not any single LEDs are lit. I emailed [email protected] and got replied which direct me to contact burninmining, which has not responded. Please help. Thank you.
Referring to order no:1509, upon receiving my 3 bitburner fury boards,1 of the boards does not power up/malfunction. Not any single LEDs are lit. I emailed [email protected] and got replied which direct me to contact burninmining, which has not responded. Please help. Thank you.
Similar situation here. One of my Bitburner Fury boards died shortly after it began hashing. It didn't even last 2 days. Maybe 36 hours. Now it is dead, no lights, no nothing. Just dead.
I left a PM for cryptx, but so far, no response.
I followed up with an email to [email protected], and I await a response.
By the way, I purchased these boards before the price was dropped to 1.5 BTC.
Let's just say I paid almost double that. Last week. I'm not pleased at all.
Cryptx -- I would appreciate a response. Thanks.
I tried other pcie which works for other boards and it did not start up that faulty board. Tried power stacking but nothing happened.
Hi,
Referring to order no:1509, upon receiving my 3 bitburner fury boards,1 of the boards does not power up/malfunction. Not any single LEDs are lit. I emailed [email protected] and got replied which direct me to contact burninmining, which has not responded. Please help. Thank you.
Referring to order no:1509, upon receiving my 3 bitburner fury boards,1 of the boards does not power up/malfunction. Not any single LEDs are lit. I emailed [email protected] and got replied which direct me to contact burninmining, which has not responded. Please help. Thank you.
So your other boards work? Have you tried swapping the PCIE leads or power stacking them ?
Hi,
Referring to order no:1509, upon receiving my 3 bitburner fury boards,1 of the boards does not power up/malfunction. Not any single LEDs are lit. I emailed [email protected] and got replied which direct me to contact burninmining, which has not responded. Please help. Thank you.
Referring to order no:1509, upon receiving my 3 bitburner fury boards,1 of the boards does not power up/malfunction. Not any single LEDs are lit. I emailed [email protected] and got replied which direct me to contact burninmining, which has not responded. Please help. Thank you.
HW-Error Rate is: 3.87
Where can i find this info in cgminer screen? 
Is the official firmware?
How I can install it
How I can install it
Just fyi:
4 boards, connected by CANBus:
This firmware from asic-shop.com: https://www.dropbox.com/s/tz9xukd4d75g5uq/BitBurnerFury_for_bootloader.hex
using this:
cgminer --usb 1:7 --disable-gpu --avalon-options 115200:128:10:45:280 --bitburner-voltage 1360 --avalon-cutoff 63 --avalon-fan 80 --avalon-temp 55
HW-Error Rate is: 3.87
might try to tweak further, will keep you posted..
4 boards, connected by CANBus:
This firmware from asic-shop.com: https://www.dropbox.com/s/tz9xukd4d75g5uq/BitBurnerFury_for_bootloader.hex
using this:
cgminer --usb 1:7 --disable-gpu --avalon-options 115200:128:10:45:280 --bitburner-voltage 1360 --avalon-cutoff 63 --avalon-fan 80 --avalon-temp 55
HW-Error Rate is: 3.87
might try to tweak further, will keep you posted..
UPDATE
We are sold out
We are sold out
Ok now wait a while.. during the first minutes the HW rate is usually a bit higher...
If you are not getting close to 100Ghs, then try to reduce frequency in steps of 2 to find better settings. I always mine 100'000 shares before I change settings.
If you are not getting close to 100Ghs, then try to reduce frequency in steps of 2 to find better settings. I always mine 100'000 shares before I change settings.
Thanks a lot dego!
I need a CAN bus cable, to connect two boards,
Can anyone help me where to get one?
CryptX is out of stock with them.
Can anyone help me where to get one?
CryptX is out of stock with them.
Id you don't find the Can bus cable, you can try with usb cables.
Ok now wait a while.. during the first minutes the HW rate is usually a bit higher...
If you are not getting close to 100Ghs, then try to reduce frequency in steps of 2 to find better settings. I always mine 100'000 shares before I change settings.
If you are not getting close to 100Ghs, then try to reduce frequency in steps of 2 to find better settings. I always mine 100'000 shares before I change settings.
I need a CAN bus cable, to connect two boards,
Can anyone help me where to get one?
CryptX is out of stock with them.
Can anyone help me where to get one?
CryptX is out of stock with them.
Ah no, you are still using the wrong voltage command!
you have to use --bitburner-fury-voltage with your firmware
leave the boards connected by CAN bus (not sure if the missing jumpers really matter) and try this line (copy paste!)
--avalon-options 115200:64:10:47:280 --bitburner-fury-voltage 960 --avalon-cutoff 63 --avalon-fan 80 --avalon-temp 55
you have to use --bitburner-fury-voltage with your firmware
leave the boards connected by CAN bus (not sure if the missing jumpers really matter) and try this line (copy paste!)
--avalon-options 115200:64:10:47:280 --bitburner-fury-voltage 960 --avalon-cutoff 63 --avalon-fan 80 --avalon-temp 55
(5s):99.04G (avg):84.14Gh/s | A:1031 R:198 HW:1651 WU:1175.4/m
ST: 2 SS: 0 NB: 2 LW: 3022 GF: 0 RF: 0
Connected to stratum.bitcoin.cz diff 85 with stratum as user joshka.worker2
Block: 0003964399d45361... Diff:609M Started: [11:35:39] Best share: 18.5K
--------------------------------------------------------------------------------
[P]ool management Settings [D]isplay options [Q]uit
BBF 0: 40C 280 986mV | 87.64G/84.14Gh/s | A:1031 R:198 HW:1651 WU:1179.1/m
-------------------------------------------------------------------------------------------------------------------------
(5s):93.87G (avg):85.68Gh/s | A:3292 R:368 HW:2222 WU:1197.3/m
ST: 2 SS: 0 NB: 2 LW: 7703 GF: 0 RF: 0
Connected to stratum.bitcoin.cz diff 34 with stratum as user joshka.worker2
Block: 0003964399d45361... Diff:609M Started: [11:35:39] Best share: 18.5K
--------------------------------------------------------------------------------
[P]ool management Settings [D]isplay options [Q]uit
BBF 0: 44C 280 989mV | 88.45G/87.58Gh/s | A:3394 R:368 HW:2242 WU:1224.1/m
Ah no, you are still using the wrong voltage command!
you have to use --bitburner-fury-voltage with your firmware
leave the boards connected by CAN bus (not sure if the missing jumpers really matter) and try this line (copy paste!)
--avalon-options 115200:64:10:47:280 --bitburner-fury-voltage 960 --avalon-cutoff 63 --avalon-fan 80 --avalon-temp 55
you have to use --bitburner-fury-voltage with your firmware
leave the boards connected by CAN bus (not sure if the missing jumpers really matter) and try this line (copy paste!)
--avalon-options 115200:64:10:47:280 --bitburner-fury-voltage 960 --avalon-cutoff 63 --avalon-fan 80 --avalon-temp 55
If that is tha hasrate of 1 board then it's pretty good....
Maybe you could shut it down, deconnect 1 board and try again to see if its only the mini usb connected board...
Maybe you could shut it down, deconnect 1 board and try again to see if its only the mini usb connected board...
In the screenshot:
screen sudo ./cgminer -o stratum+tcp://stratum.bitcoin.cz:3333 -u joshka.worker2 -p x --avalon-options 115200:64:10:47:280 --bitburner-voltage 960 --avalon-cutoff 63 --avalon-fan 80 --avalon-temp 55
And now:
screen sudo ./cgminer -o stratum+tcp://stratum.bitcoin.cz:3333 -u joshka.worker2 -p x --avalon-options 115200:32:10:47:280 --bitburner-voltage 960 --avalon-cutoff 63 --avalon-fan 80 --avalon-temp 55
I put 32 insted 64 because I don't have jumpers, I will terminate the canbus later or I will plugin another usb wire.
With the last command:
screen sudo ./cgminer -o stratum+tcp://stratum.bitcoin.cz:3333 -u joshka.worker2 -p x --avalon-options 115200:64:10:47:280 --bitburner-voltage 960 --avalon-cutoff 63 --avalon-fan 80 --avalon-temp 55
And now:
screen sudo ./cgminer -o stratum+tcp://stratum.bitcoin.cz:3333 -u joshka.worker2 -p x --avalon-options 115200:32:10:47:280 --bitburner-voltage 960 --avalon-cutoff 63 --avalon-fan 80 --avalon-temp 55
I put 32 insted 64 because I don't have jumpers, I will terminate the canbus later or I will plugin another usb wire.
With the last command:
Not really... 
What did you do?
- Terminated Can Bus correctly?
- command?
What did you do?
- Terminated Can Bus correctly?
- command?
Jump to: