Topic: Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux) - page 109. (Read 6590757 times)

hello,

i have latest wn 10, amd 19.5.2 and claymore 14.7 and despsite i use rxboost or strapo value, still getting same ahsrate with or without it.
i had 14.6, downloaded 14.7, used driver uninstall, rebooted, then driver install, again reboot but still getting same hash.

it wrote rxoption is applied succesfuly, same for strap, but i do not see any changes in hashrate...any advice what could be wrong?

First, show the startup parameters of the Claymore;
Second, install any monitoring programme (HWiNFO64 or OpenHardwareMonitor).
Most likely your problem is related to the set temperature limit parameters. For example, there is a temperature limit of 70 (-tt 70) and when the card is heated above this temperature it resets the frequency.

I am making everything on my pc, without a Teamviewer.
I want Core Clock to be 1150, but it is always somewhere - up or down.
This starts may be 2-3  min from the beginning, it is not connected with a poll change.
May be GPU temperature is the problem - when the temp is around 71-72 C...
But I haven't tt or other parameters about temp in my config...

How often? This can be when reconnecting to pools (your pool and dev-fee pool), the formation of a new DAG's. If it's remote farm while on the Teamviewer may also fall frequency.

Core Clock is up and down - why it can't stay on one place?

@claymore, anyway you can disclose your timings if we decide to use on our own?

Hi,

Had a similar issue.

For me the issue was due to the power cable to the riser. .

Thanks for the update! This is much easier to use now with the new driver!

Hal

The fact that it crashes with 'one gpu less' really sounds like a PCI-E Riser or MOtherboard PCI-E issue. I think what happening is when it tries to start that GPU it crashes because it's not getting the information across normally or it's losing signal.

Try Running the Claymore 14.7 miner ONE gpu at a time until the DAG is created and it does a few hashes. Shut down, plug in the next GPU and same thing. Repeat until you find the GPU/Riser that's crashing the system.

Thanks a lot for the reply,

I am Running on windows
I have not (yet) any afterburner installed. i am not overclocking and have the full power (1600W ) available


Claymore 12.0
When i run claymore 12.0 , its finds the pool and after create DAG for each GPU, the screen freezes, and i have to manually (swich of power) restart
when i wait longer i get the blue windows screen DPC watchdog violation

Claymore 14.7
When i run claymore 14.7 , its is running bit better, One of the GPU s (sometime GPU4 and somethimes GPU 3) is on 0
NVML: can not get current temperature error 15.
then it reboots with one GPU less.


Any idea ?

thanks

I have the same problem on windows with rx580 8gb.
when i run with -rxboost 1 - strap 1, it tells me to run it with -driver uninstall.
I run it with that as admin, reboot and then remove it. Run it again as admin, and then normally.
It says driver is in use...
I also tried including -driver install_test but i see no improvement.
Anybody knows what to do to get it work?

Thanks

Are you overclocking at all? and Have you tried 14.7? This Linux or Windows? by stuck do you mean the Miner freezes or does your computer lock-up?

CLAYMORE STUCK AFTER START

Who is the magic wizard that can help me out,

I have been going to all posts, but I cant get a suitable solution for my problem with Claymore 12.0. Tried everything.


Later versions of claymore give me the Can not create DAG file, problem.  Which is said to be a virt mem problem. (i ve put the virt mem to even 50GB, and even tried 80GB) went throught the CHKDSK /f /r solutions and sata AHCI controller driver solutions.
Or I get a video TDR failure, which should be a driver issue.


I cant figure out why half of my miners suddenly are stuck... and the rest are working fine... ? exactelly same BIOS setup, same CPU, same DDR. Both miners are in every way: an exact clone.

Throuble shooting:
swapped all risers with GPUs from the working one to the one that stucks.
i went through BIOS, 4G is on. tried GEN1 and GEN2....GEN AUTO   (the working miner is actually even on GEN  AUTO)
But...
So when i swap the SSD only from the working RIG to the exact same RIG, that isnt working... claymore gets stuck again....

Tried to restart / reload windows 6 times.
With first having 1 GPU, and adding everytime an extra one.

I have a 6 GPU 1080TI card, with the latest Nvidia drivers installed, (used DDU, took the Latest Nvidea driver, and as well tried 425.1 and 430.86)  
Asrock BTC pro 2.0 board latest Bios update with the 4g decoding option which is ON) , with 16GB DDR, intel i5 4core processor. 256 samsung EVO SSD.


setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100
EthDcrMiner64.exe -epool us1.ethermine.org:4444 -ewal 0xc20ca97592ecfbd89a86df556b7784376a672e30.miner1 -epsw x -dpool stratum+tcp://lbry.suprnova.cc:6256 -dwal my.miner1 1 -dpsw x -dcoin lbc


what on earth can it be? what am i over seeing wrong for the last weeks?
wont make sence why same hardware works with one miner and not with the other one. I tried swappin SSD, or cloning an IMG file.


additional info:
Thanks a lot for the reply,

I am Running on windows
I have not (yet) any afterburner installed. i am not overclocking and have the full power (1600W ) available


Claymore 12.0
When i run claymore 12.0 , its finds the pool and after create DAG for each GPU, the screen freezes, and i have to manually (swich of power) restart
when i wait longer i get the blue windows screen DPC watchdog violation

Claymore 14.7
When i run claymore 14.7 , its is running bit better, One of the GPU s (sometime GPU4 and somethimes GPU 3) is on 0
NVML: can not get current temperature error 15.
then it reboots with one GPU less.



Any help Would be Appreciated, and rewarded from my side!!


thanks in advance

you will win

https://investoon.com/tools/dag_size

What     is  wrong          with your                        keyboard     ?

Dear Claymore  Developers

I am very sorry that  so  many  core root uneducated morons and   idiots  asking you for so many  things ,  please  just  ignore  them .


have a good day


b.t.w

lets try to guess   BTC  price for  end of  June 2019 ?     I bet  9900$

Well ok, but OpenCL API is available for vega10/20, only difference is OpenCL 2.0 instead of 1.2 for polaris card..
Claymore works with both OpenCL Apis while you're not mixing cards, like there are two versions of OpenCL api there are two platforms.. but both are AMD ones.. so I don't see why it is not possible..
As you can see :

This is provided using OpenCL API in C.

So many crashes on 14.7.. gpu hangs, freezes etc. 14.5 works ok but crashes some times too. The new version is faster but not stable at all imo. Hope this fixed soon. going back to older version for now.

how to get coins on the Keccak algorithm, not getting the algorithm ethash?