Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux) - page 471.

Vann

hero member

Activity: 1036

Merit: 606

Quote from: ?? on ??

Guys how do minimise the no of stale shares...i grt aroumd 5 to 10% every 10 min...i m mining on ethermine..apart from tht evrytyn s working fine...

The 4 Billion share difficulty that Ethermine uses is too low for the 15 second block times since the Byzantium fork. I switched to Nanopool that uses a 10 Billion share difficulty and my estimated hashrate on Nanopool is much closer to my reported hash rate.

z0n0

legendary

Activity: 1274

Merit: 1006

Guys, need some help:
Started to building a 6 GPU rig (RX580 Sapphire Pulse 4gb Elpida).
Flashed every card one by one.

When I'm at 3 cards, msi afterburner works normal, but when I plug the 4th card, msi afterburner dies (check the picture).
How can I fix this?

If that doesn't work, is there a way in AMD Radeon settings to load custom profile on every boot? I modded clock, saved the profile but after fresh boot the clocks reset to default.

Pls advise, many thanks!

santan

member

Activity: 102

Merit: 11

Claymore never thinks of writing on screen the Mining difficulty of share found.... even if he is calculating and comparing it to the pool accepted difficulty before sending the share to the pool.

delbarbour

newbie

Activity: 72

Merit: 0

Quote from: ?? on ??

Quote from: e97 on January 18, 2018, 10:06:23 PM

Quote from: e97 on January 15, 2018, 08:24:03 PM

thanks claymore!

shows 44 Mh/s on Vega64 and 37 Mh/s on 1080 Ti, hopefully number of submitted shares shows a similar increase

ethminer seems to run a bit faster on the 1080 Ti, any chance you could integrate those improvements? might be from cuda-9 code.

Reported:

miner	vega 64	1080 ti	combined
ethminer	42	38	80
claymore	44	37	81

Will report back on accepted share rate after 24 hours.

ethminer gives me ~ 56.16 shares per hour
claymore gives me ~ 55.64 shares per hour

claymore reports a higher hash rate but im seeing less shares per hour, even with the 1% dev fee, theres something off. for now im switching back to ethminer.

lol

Set -dcri to 5 , 10 or 15 max even when solo mining Wink

igotfits

full member

Activity: 298

Merit: 100

Quote from: bubbagump on January 19, 2018, 02:29:07 AM

Quote from: igotfits on January 19, 2018, 02:25:54 AM

What's the latest drivers from AMD we can use with 10.5, are we still stuck with blockchain drivers? Huh

?

The latest adrenalin drivers work fine for me, but I don't use any of the temp or voltage controls in the miner so YMMV.

i only OC i don't mess with anything else. the voltage i flashed in bios, i only want to control the OC with afterburner.

Jbodz83

newbie

Activity: 124

Merit: 0

weird thing happened today morning and im still trying to figure it out.

My GPU Hashrate drop from 30.2 -> 21.1 while mining ETHEREUM, however, when i tried to switch on MUSICOIN or UBIQ my hashrate is at 30.2.

any idea what could be the cause? Roll Eyes

bubbagump

jr. member

Activity: 104

Merit: 3

Quote from: igotfits on January 19, 2018, 02:25:54 AM

What's the latest drivers from AMD we can use with 10.5, are we still stuck with blockchain drivers? Huh

?

The latest adrenalin drivers work fine for me, but I don't use any of the temp or voltage controls in the miner so YMMV.

igotfits

full member

Activity: 298

Merit: 100

What's the latest drivers from AMD we can use with 10.5, are we still stuck with blockchain drivers? Huh

?

Daniel0303

newbie

Activity: 31

Merit: 0

halo,

How to force a fan speed in claymore miner?

tt -100 seems doesn't work for me

AMD driver 17.11.1
Claymore v9.5,v10.3,v10.4,v10.5
Windows 10 1709
Asus strix rx 580 samsung

Thanks

e97

jr. member

Activity: 58

Merit: 1

Quote from: e97 on January 15, 2018, 08:24:03 PM

thanks claymore!

shows 44 Mh/s on Vega64 and 37 Mh/s on 1080 Ti, hopefully number of submitted shares shows a similar increase

ethminer seems to run a bit faster on the 1080 Ti, any chance you could integrate those improvements? might be from cuda-9 code.

Reported:

miner	vega 64	1080 ti	combined
ethminer	42	38	80
claymore	44	37	81

Will report back on accepted share rate after 24 hours.

ethminer gives me ~ 56.16 shares per hour
claymore gives me ~ 55.64 shares per hour

claymore reports a higher hash rate but im seeing less shares per hour, even with the 1% dev fee, theres something off. for now im switching back to ethminer.

wtfonly16

full member

Activity: 285

Merit: 105

ye no more tempenture hangs here too 16 restarts a day, going 8 hours now no restart!

emadradi

newbie

Activity: 8

Merit: 0

Hey Claymore,

What is " Illegal memory access "

I couldn't figure out how to deal with this problem , and my miner is not working since three days becasue of it.

Could you please tell me how to fix it.

I'm mining ETH with 1070 GTX 6 cards
calymore ver 9.4
the vertual memory is 35000 mb
Huh

PLEASE HELP

THANKS IN ADVANCE

cantr

member

Activity: 124

Merit: 10

Hi!
i am member of a mining group on facebook. after jan 16, many of the long-time stable rigs have melted PSU outputs. and also i have same problem with them. is there any relation with the temperature control problem that we took the mistake of? Is anyone else in the forum experiencing the same problem from January 14th to 17th?
best regards

---------------------------

Danpeal

newbie

Activity: 3

Merit: 0

Quote from: muzuca on January 11, 2018, 08:48:51 PM

Quote from: Danpeal on January 11, 2018, 03:50:34 PM

Hi guys,

I'm having problems with my sapphire RX580 nitro+, 8g where the hashrate goes down to 20MH/s from time to time (each 20s- 1 minute)

Here is my config :

- Claymore 10.0 ( tried 10.3 but same issue ). Eheruem mining only.
- 4 x Sapphire RX580 nitro+, 8g .
- Windows 10 pro.
- amd block chain driver Augst23.
- MSI after burner for over clocking (memory 2250, Core 1400).

the logs seems okey to me, but I'll put them below maybe u find something I missed

Code:

20:35:17:637 4ec ETH: 01/11/18-20:35:17 - New job from eu1.ethermine.org:14444
20:35:17:637 4ec target: 0x0000000112e0be82 (diff: 4000MH), epoch 163(2.27GB)
20:35:17:637 4ec ETH - Total Speed: 127.518 Mh/s, Total Shares: 5212, Rejected: 0, Time: 47:00
20:35:17:637 4ec ETH: GPU0 31.875 Mh/s, GPU1 31.895 Mh/s, GPU2 31.853 Mh/s, GPU3 31.895 Mh/s
20:35:22:106 4ec send: {"id":6,"jsonrpc":"2.0","method":"eth_submitHashrate","params":["0x7992b40", "0x00000000000000000000000000000000000000000000000000000000087ce52f"]}

anyhelp would be much appreciated

I think that are you putting so much power in your GPUs and for some reason the speed drops... what kind of PSU do you have, maybe is something with the energy supply from the PSU... I have 3 rigs with those cards, and my perfect conf was 1250 2250... depending of the GPU I need to put less power as 1200 2000 or 1150 2150.

Thank you for the reply. I'm using Seasonic P-860 Platinum 80PLUS Platinum (860W) with 4 GPU. I believe it's more than enough sense one GPU is consuming around 145W.

Can you share your setup ? are u running them at 31.8... MHash/s !

Piradoxlanieve

newbie

Activity: 71

Merit: 0

I have miners in different ip, but this same person (107.172.193.158) this person try restart my miners and you use 2 different ips

Remote management: read-only only, command miner_reboot ignored. Remote IP: 107.172.193.158 Undecided

sorry my english

mikkowendell

newbie

Activity: 41

Merit: 0

AGAIN, check your pcie and sata cables, every part of it and see if there are some burn............................................................always

this is one of the main reason of CRASHING..................................

Ursul0

sr. member

Activity: 857

Merit: 262

Quote from: MassDestruction on January 18, 2018, 01:30:09 PM

Hey Guys

I'm having this weird issue with my rig where it will crash and down the system everyday at 7AM. I'm currently using nvoc 19(ubuntu) with claymore miner to mine ETH. Currently this feels like a software issue, and I'm exploring my options to see what the possible culprit is.

So what could Claymore be doing to cause this issue if it is? If so are there any possible solutions? I've provided info about my rig, settings, and the mining pool if that helps.

Mining Pool:
us1.ethermine.org:4444

Claymore Settings:
-epsw x
-mode 1
-dbg -1

Rig info:
Mother Board: Biostar TB250 Pro
Video Cards: 1 x GTX 1070, 7 x GTX 1060, 2 x GTX 1050Ti
Ram Size: 16 GB
Storage: SanDisk 120GB SSD
Processor: Intel Celeron G3900
Power Supply: Corsair AX860, Corsair VX550

You may try to look for scheduled tasks and remove all the crap you may find there

rorschach1

hero member

Activity: 840

Merit: 503

Quote from: JuanDoe on January 18, 2018, 03:17:12 PM

Hi,

In near future are plans for Claymore to mining more coins than only Decred, Pascal, Library and Sia on dual mining?

Is very interesting is can be mining more coins on dual.

I think dual mining have no sense. I don't see much profit in dual. Moreover I have less profit in dual than solo.

j2james

newbie

Activity: 80

Merit: 0

Quote from: Metroid on January 18, 2018, 02:11:58 PM

Quote from: j2james on January 18, 2018, 02:08:39 PM

Quote from: Claymore on January 18, 2018, 08:52:03 AM

v10.5:- added version for CUDA 9.1

Hi. Tell me please what should I do to use CUDA 9.1?

Looks like I still use 8.0:

CUDA Driver Version/Runtime Version: 9.1/8.0

you need to update the nvidia drivers to latest.

Thank you, but no

I just need to copy files from cuda9.1 folder to claymore folder: EthDcrMiner64.exe and cudart64_91.dll. And then 9.1 will work. By default 8.0 works.

JuanDoe

newbie

Activity: 1

Merit: 0

Hi,

In near future are plans for Claymore to mining more coins than only Decred, Pascal, Library and Sia on dual mining?

Is very interesting is can be mining more coins on dual.

Topic: Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux) - page 471. (Read 6590565 times)