Claymore's ZCash/BTG AMD GPU Miner v12.6 (Windows/Linux) - page 54.

Hallmader

sr. member

Activity: 1123

Merit: 253

Quote from: ramor14 on June 07, 2017, 04:52:50 AM

Hi everyone,

I've few rigs using Claymore miner (9.4 , windows 10, crimson 16.9.1), I observed both stability and performances are much higher when only one GPU (GB rx 470 4g) is plugged on the rig. I achieved to get 27mhs/500mhs (eth/sc) with one gpu over hours, then I decided to keep these settings which seemed stable enough for the whole rig. However the performances of the 6 gpus are actually much lower, around 22mhs/300mhs per gpu, and the rig crashes often (wattman error). Is there something I can do to fix this issue?

Thanks

I do not see difference with multiple GPU. So you may reduce the frequnecy to make them more stable.

ramor14

newbie

Activity: 1

Merit: 0

Hi everyone,

I've few rigs using Claymore miner (9.4 , windows 10, crimson 16.9.1), I observed both stability and performances are much higher when only one GPU (GB rx 470 4g) is plugged on the rig. I achieved to get 27mhs/500mhs (eth/sc) with one gpu over hours, then I decided to keep these settings which seemed stable enough for the whole rig. However the performances of the 6 gpus are actually much lower, around 22mhs/300mhs per gpu, and the rig crashes often (wattman error). Is there something I can do to fix this issue?

Thanks

blackjok3r

newbie

Activity: 35

Merit: 0

Anyone had their hash rate drop by 100 randomly? Left mine on last night and when I got up this morning it had dropped from 300 to 200. A restart fixed it, my clocks were the same in gpu-z and gpu still showed 99% usage.

fredeq

legendary

Activity: 1537

Merit: 1005

Quote from: fredeq on June 06, 2017, 04:14:28 PM

Doh!
I just realized I was running 12.4 version.

Updated to 12.5, so far so good.

@Valgar nicehash released new version of the miner with updated CM miners, check if it helps.

All good after the night as well. My rejects are now solved.

QuintLeo

legendary

Activity: 1498

Merit: 1030

Quote from: erk on June 06, 2017, 06:52:12 PM

Quote from: QuintLeo on June 06, 2017, 05:32:47 PM

R9 280x should run fine on Ubuntu 14.04 with the fglrx 15.12 drivers - but I think you have to manually download them and install, I don't remember them being an apt-get options anywhere offhand.

I am running fglrx(0): Version: 15.20.3 which was installed from the additional drivers menu in the Xubuntu 14.04 GUI.

I'm pretty sure that's the 15.7 drivers - fglrx 15.12 drivers identify as 15.302.something or some such.
I don't have access to any of my LINUX boxes to check right now, as they're all in my new place and I'm typing this from my old place.

Bwtmn7

member

Activity: 109

Merit: 10

Quote from: kaese2002 on June 06, 2017, 06:08:17 AM

Quote from: Bwtmn7 on June 05, 2017, 06:01:30 PM

has anyone setup claymore miner 12.4 with Fury and a newer driver than 16.3.2? because for me isnt working

Fury should still use 15.12...running @440H/s each

Quote from: th00ber on June 06, 2017, 01:21:19 AM

Quote from: Bwtmn7 on June 05, 2017, 06:01:30 PM

has anyone setup claymore miner 12.4 with Fury and a newer driver than 16.3.2? because for me isnt working

R9 Fury here !
Claymore 12.5 (-asm 1 -a 2 -i 5)
Driver 15.12
400-430H/s with powerlimit -50% (125w)

It's important to stick with those drivers, that is the best perf I got.
(With newer driver, I can't activate the ASM option, with give me around 340 H/s for the same powerlimit)

Here my dashboard : http://www.monitorig.com/#?panel=dashboard&id=1086db9224632d26671ab42df5ee1d92bf0187bbdd

but Polaris cant work with 15.12

erk

hero member

Activity: 826

Merit: 500

Quote from: QuintLeo on June 06, 2017, 05:32:47 PM

Quote from: Valgar on June 06, 2017, 03:26:48 PM

I'm getting a lot of issues with the Claymore miner within NiceHash in the past week, anyone else getting this?

This happens on 3 separate rigs running different cards, Furys, 280 and 390.

What often happens is periods of rejected shares even though the cards are rock solid stable and periods of disconnects/timeouts, I've tried switching regions but the same issue. If I switch miners I get no issues, but of course Claymore is the best performing.

Nicehash seems to have been doing a lot more "switching" this past few days vs it's norm - which impacts Claymore's miner more due to the overhead of setting up the SSL connection.

R9 280x should run fine on Ubuntu 14.04 with the fglrx 15.12 drivers - but I think you have to manually download them and install, I don't remember them being an apt-get options anywhere offhand.

There is ZERO reason to run "newer" drivers on that card, as long as you don't have anything more recent in the same machine with it.

I am running fglrx(0): Version: 15.20.3 which was installed from the additional drivers menu in the Xubuntu 14.04 GUI.

Should I update to Claymore v12.5 ?

QuintLeo

legendary

Activity: 1498

Merit: 1030

Quote from: Valgar on June 06, 2017, 03:26:48 PM

I'm getting a lot of issues with the Claymore miner within NiceHash in the past week, anyone else getting this?

This happens on 3 separate rigs running different cards, Furys, 280 and 390.

What often happens is periods of rejected shares even though the cards are rock solid stable and periods of disconnects/timeouts, I've tried switching regions but the same issue. If I switch miners I get no issues, but of course Claymore is the best performing.

Nicehash seems to have been doing a lot more "switching" this past few days vs it's norm - which impacts Claymore's miner more due to the overhead of setting up the SSL connection.

R9 280x should run fine on Ubuntu 14.04 with the fglrx 15.12 drivers - but I think you have to manually download them and install, I don't remember them being an apt-get options anywhere offhand.

There is ZERO reason to run "newer" drivers on that card, as long as you don't have anything more recent in the same machine with it.

erk

hero member

Activity: 826

Merit: 500

I just stated to get the same problem on Nicehash too.
It's rock solid on flypool mining ZEC, but I would like to mine on Nicehash now.

I am still running 12.4 about to update to 12.5 to see if it fixes the Nicecash rejects, but before I do, my video card is an old HD 7970 (R9 280x ) Tahiti chip model. I am running on Linux Ubuntu 14.04 with fglrx drivers.

Is that the optimal Linux solution for that vintage card with Claymores?

I haven't seen any later OpenCL drivers for the Tahiti chipset than the ones in Ubuntu 14.04

wa11mine

newbie

Activity: 10

Merit: 0

Quote from: tearsdontfall on June 06, 2017, 10:08:06 AM

Miner is detecting my card as 470 but my card is Sapphire nitro+ rx 570 8GB... I am getting around 275 hash... is this okay??

Not okay, you should sell the card to me Tongue

Jks. The software shows RX500 series cards as 400 series but the speed of the card is determined by the memory type. I have a hynix RX580 Nitro+ which gives 315 hashes and an elpida RX580 Nitro+ which gives 285 hashes.

Prelude

legendary

Activity: 1596

Merit: 1000

Quote from: fredeq on June 06, 2017, 04:14:28 PM

Doh!
I just realized I was running 12.4 version.

Updated to 12.5, so far so good.

@Valgar nicehash released new version of the miner with updated CM miners, check if it helps.

12.5 has the issue as well.

The problem is almost certainly on nicehash's side. Come report your problems here, doubt nicehash monitors this thread:

https://bitcointalksearch.org/topic/m.19402626

Valgar

newbie

Activity: 13

Merit: 0

Quote from: fredeq on June 06, 2017, 04:14:28 PM

Doh!
I just realized I was running 12.4 version.

Updated to 12.5, so far so good.

@Valgar nicehash released new version of the miner with updated CM miners, check if it helps.

Thanks for the tip! I'll give it a go, also for some reason Windows had just decided that after 3 weeks of mining it would block the miner which is why I got disconnects, thanks for the help Claymore!

Edit: seems to be working much better now, my 280 which has stability issues before seems to be better too.

aleksandar221

newbie

Activity: 1

Merit: 0

When I start the miner it loads and when connecting to pool it crash. I am using 15.12 driver and I have R9 280x , please help...

log

22:45:57:722   1ddc   args: xxxxx
22:45:57:727   1ddc
22:45:57:732   1ddc   ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»
22:45:57:737   1ddc   º Claymore's ZCash AMD GPU Miner v12.5 º
22:45:57:741   1ddc   ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ¼
22:45:57:749   1ddc
22:45:57:958   1ddc   ZEC: 1 pool is specified
22:45:57:966   1ddc   Main ZCash pool is eu1-zcash.flypool.org:3333

fredeq

legendary

Activity: 1537

Merit: 1005

Doh!
I just realized I was running 12.4 version.

Updated to 12.5, so far so good.

@Valgar nicehash released new version of the miner with updated CM miners, check if it helps.

Valgar

newbie

Activity: 13

Merit: 0

Quote from: Claymore on June 06, 2017, 03:47:58 PM

Please PM me the log file so I can check the reason.

Which logfile is this? The Nicehash one Named "log" or "log1"?

fredeq

legendary

Activity: 1537

Merit: 1005

Quote from: Claymore on June 06, 2017, 03:47:58 PM

Quote from: fredeq on June 06, 2017, 03:44:06 PM

Quote from: Valgar on June 06, 2017, 03:26:48 PM

I'm getting a lot of issues with the Claymore miner within NiceHash in the past week, anyone else getting this?

This happens on 3 separate rigs running different cards, Furys, 280 and 390.

What often happens is periods of rejected shares even though the cards are rock solid stable and periods of disconnects/timeouts, I've tried switching regions but the same issue. If I switch miners I get no issues, but of course Claymore is the best performing.

Getting the same.
My idea is there is a new coin out there that is not properly supported by CM miner, hence the rejects.
Hush? Zencash?

Please PM me the log file so I can check the reason.

Log sent. I think nicehash also sent new diff right before rejects started "Pool sets new share target: 0x000f0f0f (diff: 4352H)"

Claymore

donator

Activity: 1610

Merit: 1325

Miners developer

Quote from: fredeq on June 06, 2017, 03:44:06 PM

Quote from: Valgar on June 06, 2017, 03:26:48 PM

I'm getting a lot of issues with the Claymore miner within NiceHash in the past week, anyone else getting this?

This happens on 3 separate rigs running different cards, Furys, 280 and 390.

What often happens is periods of rejected shares even though the cards are rock solid stable and periods of disconnects/timeouts, I've tried switching regions but the same issue. If I switch miners I get no issues, but of course Claymore is the best performing.

Getting the same.
My idea is there is a new coin out there that is not properly supported by CM miner, hence the rejects.
Hush? Zencash?

Please PM me the log file so I can check the reason.

fredeq

legendary

Activity: 1537

Merit: 1005

Quote from: Valgar on June 06, 2017, 03:26:48 PM

I'm getting a lot of issues with the Claymore miner within NiceHash in the past week, anyone else getting this?

This happens on 3 separate rigs running different cards, Furys, 280 and 390.

What often happens is periods of rejected shares even though the cards are rock solid stable and periods of disconnects/timeouts, I've tried switching regions but the same issue. If I switch miners I get no issues, but of course Claymore is the best performing.

Getting the same.
My idea is there is a new coin/pool out there that is not properly supported by CM miner, hence the rejects.
Hush? Zencash?

Valgar

newbie

Activity: 13

Merit: 0

I'm getting a lot of issues with the Claymore miner within NiceHash in the past week, anyone else getting this?

This happens on 3 separate rigs running different cards, Furys, 280 and 390.

What often happens is periods of rejected shares even though the cards are rock solid stable and periods of disconnects/timeouts, I've tried switching regions but the same issue. If I switch miners I get no issues, but of course Claymore is the best performing.

Claymore

donator

Activity: 1610

Merit: 1325

Miners developer

Quote from: Blisk on June 06, 2017, 01:53:54 PM

Linux version not working because of using old ssl library
libssl.so.1.0.0

Since you use Linux, it should not be a problem for you to get required version of OpenSSL. But I will check if I can link it statically in next update.

Quote from: yudhistira on June 06, 2017, 02:09:44 PM

Why my RIG with AMD R280 Saphire suddenly shutdown when start mining with v12.5
windows 7 64 bit RAM 4Gb
need advice please

Usually it means that your PSU is weak.

Topic: Claymore's ZCash/BTG AMD GPU Miner v12.6 (Windows/Linux) - page 54. (Read 3839203 times)