Dec 11 to Jan 11 Sidehack Compac Stick pool club latest setup. - page 13.

philipma1957

legendary

Activity: 4326

Merit: 8950

'The right to privacy matters'

Quote from: xleejohnx on December 15, 2015, 09:22:10 PM

http://solo.ckpool.org/workers/1JiWuyX94wrCr7JhkAn7x5qNMCEef1KhqX.xleejohnxdonation

putting up some donation!!! Grin

Thank you I will add it when I get to a real pc.

Edit

should be done check here

https://bitcointalksearch.org/topic/m.13210724

team total here:

http://solo.ckpool.org/users/1JiWuyX94wrCr7JhkAn7x5qNMCEef1KhqX

xleejohnx

hero member

Activity: 672

Merit: 500

http://solo.ckpool.org/workers/1JiWuyX94wrCr7JhkAn7x5qNMCEef1KhqX.xleejohnxdonation

putting up some donation!!! Grin

bix0

newbie

Activity: 15

Merit: 0

Quote from: philipma1957 on December 15, 2015, 11:36:56 AM

quick up date we have 49 filled up.

1 dropped out = 48

1 has yet to get stick started = 47 so if a block hits 1/47 of a part a each = .255 btc which is about 117 usd.

All subject to change once the new guy gets his stick working.

http://solo.ckpool.org/workers/1JiWuyX94wrCr7JhkAn7x5qNMCEef1KhqX.bix0stick

and it is up so we have 48 up and at the block.

Each share of part A = .25 as .25 x 48 = 12 coins

I just did!

Thanks for the job philipma1957 and excuse my poor english.

philipma1957

legendary

Activity: 4326

Merit: 8950

'The right to privacy matters'

quick up date we have 49 filled up.

1 dropped out = 48

1 has yet to get stick started = 47 so if a block hits 1/47 of a part a each = .255 btc which is about 117 usd.

All subject to change once the new guy gets his stick working.

http://solo.ckpool.org/workers/1JiWuyX94wrCr7JhkAn7x5qNMCEef1KhqX.bix0stick

and it is up so we have 48 up and at the block.

Each share of part A = .25 as .25 x 48 = 12 coins

my donation avalon sixes have pulled

"bestever": 4,502,660,907

http://solo.ckpool.org/workers/1JiWuyX94wrCr7JhkAn7x5qNMCEef1KhqX.philipma1957donation

cryptoglance

sr. member

Activity: 298

Merit: 250

Quote from: zOU on December 13, 2015, 12:05:54 PM

Thank you !

Noted! I should be able to get to it sometime this weekend.

philipma1957

legendary

Activity: 4326

Merit: 8950

'The right to privacy matters'

Quote from: philipma1957 on December 14, 2015, 10:21:29 PM

Quote from: bix0 on December 14, 2015, 04:30:21 PM

My european sidehack arrived today. How can i do to join the pool?

Send me a pm as you are really new to the site.

thanks for the pm we have room and you are welcome to join.

support thread below

https://bitcointalksearch.org/topic/gekkoscience-compac-bm1384-stickminer-official-support-thread-1173963

so to join please post here and use your forum name after the btc addy for the user.

url:

stratum+tcp://solo.ckpool.org:3333

user worker:

1JiWuyX94wrCr7JhkAn7x5qNMCEef1KhqX.yourforumnamestick

password :

x

your worker needs to read

http://solo.ckpool.org/workers/1JiWuyX94wrCr7JhkAn7x5qNMCEef1KhqX.bix0stick

I put you in as # 49 look at the link below

https://bitcointalksearch.org/topic/m.13210724

please post back when it is up and running.

@ SFMiner you are up and running!

http://poolmonitor.cryptoglance.info/

aarons6

legendary

Activity: 1736

Merit: 1006

Quote from: RichBC on December 15, 2015, 03:22:45 AM

Quote from: Mikestang on December 14, 2015, 07:13:17 PM

Very cool, I use CrazyGuy's R1 for my U3, too. I noticed that it's missing frequency 250, did you do a write up how to add missing frequencies? I'd like to add that one back in, even though I run my U3 at 237.5 freq normally.

I will document what I have done over in the R1 thread when I get a chance to consolidate the work, also ideally want to get aaron6 cgminer-gekko running as he reports it as handling the Compac better. I sometimes have to replug after switch on to get it hashing.

Rich

if you want to send me CG's backup file i can see what he changed and put the cgminer in there for the compacs.

RichBC

hero member

Activity: 588

Merit: 500

Quote from: Mikestang on December 14, 2015, 07:13:17 PM

Very cool, I use CrazyGuy's R1 for my U3, too. I noticed that it's missing frequency 250, did you do a write up how to add missing frequencies? I'd like to add that one back in, even though I run my U3 at 237.5 freq normally.

I will document what I have done over in the R1 thread when I get a chance to consolidate the work, also ideally want to get aaron6 cgminer-gekko running as he reports it as handling the Compac better. I sometimes have to replug after switch on to get it hashing.

I made changes to 2 files for the frequency. In /usr/lib/lua/luci/model/cbi/cgminer/cgminerconfig.lua added the following, this adds them to the pull down. Am not certain if the timeout values are correct as I just too the timeout for 125Mhz and halved it for 250MHz?

Code:

pb:value("0.34:400:0f82", translate("400M"))
pb:value("0.37:375:0e82", translate("375M"))
pb:value("0.39:350:0d82", translate("350M"))
pb:value("0.42:325:0c82", translate("325M"))
pb:value("0.45:300:0b82", translate("300M"))
pb:value("0.54:250:0982", translate("250M"))

In /etc/config/asic-freq This seems to be where the selected frequency is stored, but am not certain that this table is used?

Code:

	#option 'freq_value'    '0f82'  #400M
	#option 'chip_freq'     '400'
  	#option 'timeout'       '0.34'
	
	#option 'freq_value'    '0e82'  #375M
	#option 'chip_freq'     '375'        
	#option 'timeout'       '0.37'  
	
	#option 'freq_value'    '0d82'  #350M
	#option 'chip_freq'     '350'        
	#option 'timeout'       '0.39'  
	
	#option 'freq_value'    '0c82'  #325M
	#option 'chip_freq'     '325'        
	#option 'timeout'       '0.42'  
	
	#option 'freq_value'    '0b82'  #300M
	#option 'chip_freq'     '300'
  	#option 'timeout'       '0.45'
	
	#option 'freq_value'    '0a82'  #275M
	#option 'chip_freq'     '275'        
	#option 'timeout'       '0.50'
  	
	#option 'freq_value'    '0982'  #250M
	#option 'chip_freq'     '250'        
	#option 'timeout'       '0.54'

Please bare in mind I do not relly know what I am doing when it comes to Software, but the above sems to work. Although I cannot get the Compac to hash at 400MHz for some reason. It may be a voltage / HW thing but those look ok, so am unsure.

Rich

philipma1957

legendary

Activity: 4326

Merit: 8950

'The right to privacy matters'

Quote from: bix0 on December 14, 2015, 04:30:21 PM

My european sidehack arrived today. How can i do to join the pool?

Send me a pm as you are really new to the site.

Mikestang

legendary

Activity: 1274

Merit: 1000

Quote from: RichBC on December 14, 2015, 06:06:57 PM

The R1 runs 2 instances of cgminer with the familiar Antminer GUI and with crazyguy's firmware and a number of mods I have done adding frequencies and putting back the other stuff Bitmain took out in the R1 it works quite well.

Very cool, I use CrazyGuy's R1 for my U3, too. I noticed that it's missing frequency 250, did you do a write up how to add missing frequencies? I'd like to add that one back in, even though I run my U3 at 237.5 freq normally.

RichBC

hero member

Activity: 588

Merit: 500

Quote from: Mikestang on December 14, 2015, 05:42:06 PM

Quote from: RichBC on December 14, 2015, 03:53:37 PM

I am running my Compac on the R1 using the standard U3 cgminer. It's kind of neat as it stands alone & I have pointed the R1 chip to Donate. R1 is running at 300MHz and the Compac at 375MHz.

aarons6 has ported cgminer-gekko to the R1 but I have not been able to get it to run at the moment.

Oh, well that's cool that it will work like that. Do you have the compac plugged into a hub, then the R1 (like it says to do for the U3)?

Also, how do you change the compac frequency while it's controlled by the R1? The pull-down menu is populated with frequencies for the U3.

It's a bit of a lash up at the Moment. I took my R1 apart & mounted it on a board with a fan and fan controller, plugged up an external 5V PSU to see how high I could clock it. Then when I got the Compac, that is plugged from the R1 USB via a Hub with a separate supply cooled by the same fan as the R1 innards.

I will tidy it up at some point, repackage the R1 and run it all on a single 5V supply and get rid of the Hub, but this is easier for playing...

The R1 runs 2 instances of cgminer with the familiar Antminer GUI and with crazyguy's firmware and a number of mods I have done adding frequencies and putting back the other stuff Bitmain took out in the R1 it works quite well.

Rich

Mikestang

legendary

Activity: 1274

Merit: 1000

Quote from: RichBC on December 14, 2015, 03:53:37 PM

I am running my Compac on the R1 using the standard U3 cgminer. It's kind of neat as it stands alone & I have pointed the R1 chip to Donate. R1 is running at 300MHz and the Compac at 375MHz.

aarons6 has ported cgminer-gekko to the R1 but I have not been able to get it to run at the moment.

Oh, well that's cool that it will work like that. Do you have the compac plugged into a hub, then the R1 (like it says to do for the U3)?

Also, how do you change the compac frequency while it's controlled by the R1? The pull-down menu is populated with frequencies for the U3.

bix0

newbie

Activity: 15

Merit: 0

My european sidehack arrived today. How can i do to join the pool?

AJRGale

hero member

Activity: 767

Merit: 500

Quote from: philipma1957 on December 14, 2015, 11:50:21 AM

@ SFminer whats up? did you startmining ? I just checked and
I see you are mining to

http://solo.ckpool.org/workers/1Hy4xM3HgTZ5myGUUpDvAGYqHCS1KeKxtm.SFMiner

{"hashrate1m": "16.5G", "hashrate5m": "13.8G", "hashrate1hr": "13.2G", "hashrate1d": "13.2G", "hashrate7d": "4.63G", "lastupdate": 1450112436, "shares": 794390, "bestshare": 1096765.4741425684, "bestever": 1096765}

So I guess you rather mine alone or maybe you don't understand you need to use .

http://solo.ckpool.org/workers/1JiWuyX94wrCr7JhkAn7x5qNMCEef1KhqX.SFMinerstick

to be in the club.

you PM'ed them about it?
if you haven and they didn't respond, I guess take it as donation..

RichBC

hero member

Activity: 588

Merit: 500

Quote from: Mikestang on December 14, 2015, 03:23:56 PM

Quote from: aarons6 on December 13, 2015, 06:32:10 AM

is anyone else in here running the compac sticks off a r1 antrouter?

Is there a firmware out there to update it to control the compac, wouldn't you need to install cgminer-gekko on the R1 first?

Quote from: hedgy73 on December 12, 2015, 11:34:39 AM

im wondering if running the 2 instances of CGMiner, on the 1 login causes one to drop the whole lot of miners its working with (eg: the 9 sticks all go down then reset usb connection)

I run 3 instances of cgminer on my desktop and don't have any issues. In fact, I think I actually noticed a performance increase from my various usb miners when I gave them each their own instances (one for compac sticks, one for nanofury sticks, one for U3 before I let the R1 take it).

I am running my Compac on the R1 using the standard U3 cgminer. It's kind of neat as it stands alone & I have pointed the R1 chip to Donate. R1 is running at 300MHz and the Compac at 375MHz.

aarons6 has ported cgminer-gekko to the R1 but I have not been able to get it to run at the moment.

Rich

Mikestang

legendary

Activity: 1274

Merit: 1000

Quote from: aarons6 on December 13, 2015, 06:32:10 AM

is anyone else in here running the compac sticks off a r1 antrouter?

Is there a firmware out there to update it to control the compac, wouldn't you need to install cgminer-gekko on the R1 first?

Quote from: hedgy73 on December 12, 2015, 11:34:39 AM

im wondering if running the 2 instances of CGMiner, on the 1 login causes one to drop the whole lot of miners its working with (eg: the 9 sticks all go down then reset usb connection)

I run 3 instances of cgminer on my desktop and don't have any issues. In fact, I think I actually noticed a performance increase from my various usb miners when I gave them each their own instances (one for compac sticks, one for nanofury sticks, one for U3 before I let the R1 take it).

RichBC

hero member

Activity: 588

Merit: 500

Quote from: Mikestang on December 14, 2015, 02:44:46 PM

Quote from: RichBC on December 13, 2015, 06:13:59 AM

I have noticed that with the low hash rate of the sticks the Difficulty takes 10 Mins or so to adjust down from 1K. Is there any way to set the Pool to something lower at start up?

Rich

The command varies depending which mining client you are using, cg or bfg, but there are commands for both to set a lower starting difficulty. It's cosmetic, though, and has 0 impact on your hashing.

Agreed it will have no effect in the long run, however with a low hash stick and 1K difficulty it can take 20 Mins to initially get a share accepted, so it just seems much neater to give the auto set algorithm a suggestion.

I have now SSH into R1 and set the initial difficulty.

Rich

Mikestang

legendary

Activity: 1274

Merit: 1000

Quote from: RichBC on December 13, 2015, 06:13:59 AM

I have noticed that with the low hash rate of the sticks the Difficulty takes 10 Mins or so to adjust down from 1K. Is there any way to set the Pool to something lower at start up?

Rich

The command varies depending which mining client you are using, cg or bfg, but there are commands for both to set a lower starting difficulty. It's cosmetic, though, and has 0 impact on your hashing.

zOU

hero member

Activity: 728

Merit: 500

★ these are stars ★

I have 49 + donations, but that's including inactives.

as i rely on cryptoglance table, I can't change it.

hence my mistake

philipma1957

legendary

Activity: 4326

Merit: 8950

'The right to privacy matters'

Topic: Dec 11 to Jan 11 Sidehack Compac Stick pool club latest setup. - page 13. (Read 17194 times)