Topic: GUI mining - updated Dec 3 with 7970 bugfix, also supports Stratum! - page 5. (Read 3232159 times)

For everyone who is having some sort of problem with the new version, try installing the previous (2-19-12) version here:
http://www.mediafire.com/download/wyyi7wtwmsy9yyr/guiminer.zip

I tried the new version and it gave me errors so I went back to the previous version and have had no problems.

I have question regarding Eligius pool via GUIMiner.

I get constantly  "Listener for "Eligius ATI": gbt.mining.eligius.st:9337 [or getwork.mining.eligius.st:8337 not to mention bugged stratum] 08/06/2013 22:52:55, warning: job finished, 1:0:Tahiti is idle"

Then "Listener for "Eligius ATI": gbt.mining.eligius.st:9337 [ + same as above] 08/06/2013 23:02:57, long poll IO error"

And finally card just stops working with something like:


Card just spins up and down, up and down. It is more annoying than constant whine of overworked fans. GUIMiner is only way for my 7950 to work on Eligius on my primary PC. Tried to setup Eligius via CGMiner but it detects only first VGA which is GTX580 (not used for mining) even when I explicitly select 7950. BTW: If I plug GTX580 via CUDA miner on Eligius it works like charm. And if I run CGminer from Command prompt it can also run only GTX580 (Tahiti is not on list of GPUs although it is detected when cgminer is started with -n parameter).

On different PCs where I have only 1 VGA (7950) CGMiner via GUIMiner works (although it always show "connection problems" but mining works OK and I didn't noticed Listener messages.

Any tips?

W7 64b/GTX580 MSI TF3 (primary)/7950 MSI TF3 (miner)

On Slush this setup works nice, but Eligius have certain appeal to me as whole, and (sadly) Slush is often target of DDoS.

Use stratum.bitcoin.cz:3333

Also getting this error myself..

2013-06-02 16:31:02: Listener for "Default" started
2013-06-02 16:31:04: Listener for "Default": api2.bitcoin.cz:8332 02/06/2013 16:31:04, checking for stratum...
2013-06-02 16:31:04: Listener for "Default": api2.bitcoin.cz:8332 02/06/2013 16:31:04, started OpenCL miner on platform 0, device 0 (Juniper)
2013-06-02 16:31:04: Listener for "Default": api2.bitcoin.cz:8332 02/06/2013 16:31:04, no response to getwork, using as stratum
2013-06-02 16:31:04: Listener for "Default": api2.bitcoin.cz:8332 02/06/2013 16:31:04,  No JSON object could be decoded
2013-06-02 16:31:14: Listener for "Default": api2.bitcoin.cz:8332 02/06/2013 16:31:14, Failed to subscribe
2013-06-02 16:31:16: Listener for "Default": api2.bitcoin.cz:8332 02/06/2013 16:31:16, IO errors - 1, tolerance 2

i keep getting this upon starting to mine.Could anyone please help.

WARNING: ADL missing (no AMD platform?), temperature control is disabled
2013-05-27 09:34:55: Listener for "test": api2.bitcoin.cz:8332 27/05/2013 09:34:55, checking for stratum...
2013-05-27 09:34:55: Listener for "test": api2.bitcoin.cz:8332 27/05/2013 09:34:55, started OpenCL miner on platform 0, device 0 (GeForce 9600 GT)
2013-05-27 09:34:55: Listener for "test": api2.bitcoin.cz:8332 27/05/2013 09:34:55, no response to getwork, using as stratum
2013-05-27 09:34:56: Listener for "test": api2.bitcoin.cz:8332 27/05/2013 09:34:56,  No JSON object could be decoded
2013-05-27 09:35:05: Listener for "test": api2.bitcoin.cz:8332 27/05/2013 09:35:05, Failed to subscribe
2013-05-27 09:35:07: Listener for "test": api2.bitcoin.cz:8332 27/05/2013 09:35:07, IO errors - 1, tolerance 2

windows 7 64 bit (open case with a huge fan blowing into case)
ge force 9600 gt driver version 320.18
bitcoinclient .8.1
slashes pool


thanks.

Just upgraded to Windows 8 on my mining rig.  I've now got a HD5870, a HD6970 and a HD7850 all mining happily together with minimal effort.  Windows 7 was a nightmare for me with this hotch-potch of hardware.

 Hello!
This client works fine, but two times per day i receive the error:   
no response to getwork, using as stratum
Failed to subscribe
IO errors - 1, tolerance 2

after that my client stops doing anything.  is it possible to setup when client will reconnect after  any error on server?
by the way, other clients continue to work (cpuminer etc).
  Thank you.

I love guiminer and have been using it for a good while. I want to know though, is there any difference in hashrate or temps between guiminer and cgminer assuming the card settings are the same?

Bummer.. Lose modern driver optimizations. Maybe the next lowest will work.

A lot of cards have come out since the 5xxx series (6xxx, 7xxx, etc...).  Newer drivers are geared to make sure the latest cards that are out work correctly, sometimes at the expense of the older cards.  The best (mining) drivers for the 5xxx series is usually the catalyst 12.4 and SDK 2.5 versions.

HD5870 is my card as it says Cypress.

Latest Drivers.

Why would their be a conflict?

This is usually because of the latest drivers in a rig with older cards...  What cards do you have and what SDK and Catalyst Drivers are you using?

Guys I keep getting this. What could be wrong?

2013-05-13 12:06:15: Listener for "Default" started
2013-05-13 12:06:15: Listener for "Default": 13/05/2013 12:06:15, started OpenCL miner on platform 0, device 0 (Cypress)
2013-05-13 12:06:15: Listener for "Default": blankedout 13/05/2013 12:06:15, checking for stratum...
2013-05-13 12:06:16: Listener for "Default": blankedout 13/05/2013 12:06:16, diverted to stratum on blankedout
2013-05-13 12:06:18: Listener for "Default": blankedout2 13/05/2013 12:06:18, Verification failed, check hardware! (0:0:Cypress, 22a94fa9)
2013-05-13 12:06:22: Listener for "Default": blankedout 13/05/2013 12:06:22, Verification failed, check hardware! (0:0:Cypress, 6b43483d)
2013-05-13 12:06:23: Listener for "Default": blankedout 13/05/2013 12:06:23, Verification failed, check hardware! (0:0:Cypress, 8472f303)

I'm not sure if this has been asked on here before but are we going to see a version of GUIMiner that would support ASIC devices to eventually be released sometime soon?

i tried this and i get a message saying no open cl devices were found i am running an asus ASUS EAH5750 is there something else i have to be running to be able to use the guminer program.  i am running vista and just one video card just to test it out and im getting this message.  Please tell me what i should do. download something else or what am i doing wrong. 

I would have thought to look for the config file and delete it. I think when I save to the poclbm.ini file it saves where I have it on my screen. You will probably have to refill in your miners if you completely delete.

Mines got if you want to try since mines on a first screen (I couldn't find a nice page to where center of a monitor is but I assume 0,0 then width and height for top left)
 "window_position": [
        243,
        283,
        457,
        308
    ]

Hope this helps

I have Win7 x64 box as well.  I uninstalled SDK v2.8 and installed v2.7, but didn't have any success.  The windows is not hidden.  The icon is in the system tray, but if you hover on it with the mouse it quickly disappears.  You also can't alt-tab to the application.  Any other ideas?  I'm running GUIminer as administrator. 

 I was mining btc with my btcguild guiminer and today I wanted to try feathercoin mining with it . The program closed never to open.

 Now whenever I try to open up it says 'see the logfile 'C:/users............guiminer/guiminer.exe.log' for details' . And when I look inside that it says

ERROR:root:Exception:
Traceback (most recent call last):
  File "guiminer.py", line 2477, in run
  File "guiminer.py", line 1892, in __init__
  File "guiminer.py", line 2128, in load_config
  File "guiminer.py", line 1000, in start_mining
  File "subprocess.pyo", line 679, in __init__
  File "subprocess.pyo", line 896, in _execute_child
WindowsError: [Error 2] Sistem belirtilen dosyayı bulamıyor
Traceback (most recent call last):
  File "guiminer.py", line 2486, in
  File "guiminer.py", line 2477, in run
  File "guiminer.py", line 1892, in __init__
  File "guiminer.py", line 2128, in load_config
  File "guiminer.py", line 1000, in start_mining
  File "subprocess.pyo", line 679, in __init__
   
  File "subprocess.pyo", line 896, in _execute_child


 This.

 I don't know what to do thats why I came here.

i notice that few times too. click on the icon in tray so you get icon of guiminer left of tray. Than put the mouse cursor on this icon, when the small windows with guiminer appear right click on it and chose maximize.
Than you just smaller the guiminer but do not minimaze it.

Did they maybe change the server addresses. I was using the wrong port for btc guilds and had to go into the server.ini file and change it.

Other thought would be turning on the application and looking for poclbm.ini and deleting it and saving again (before closing to refresh that file). I found that on the forum when I first started and have used it many times when I changed settings and that file didn't save right.

I hope that helps.