[GUIDE] BitFury Miner Support/Tuning - page 6.

daddyfatsax

hero member

Activity: 857

Merit: 1000

Anger is a gift.

[2014-01-29 02:51:56] BSB 1cj: 8 of the last 9 results were bad, reinitializing

Can anyone tell me how to disable that chip in bfgminer? I have tried using 53, 54, etc. and I keep getting the above message. Other than that everything is fine. Thanks!

cypherdoc

legendary

Activity: 1764

Merit: 1002

Quote from: Keefe on January 28, 2014, 05:11:21 PM

Quote from: cypherdoc on January 28, 2014, 04:32:13 PM

ok, now it's happening to me; again.

absolutely no hashing with one of my 14 card rigs. changed out SD cards and raspi. can login into admin page but no hashing. took rig apart and checked for any burnt boards (none) and blew out M board connector in case of excess oxidation (none apparent).

what were all the suggestions given for this frequent problem?

I've said it many times before, so I'll let you scroll up for details, but you need to check the output of chainminer and the proxies.

i only have 2 screens:

Code:

pi@192-168-7-243:~$ sudo screen -r
There are several suitable screens on:
2069..192-168-7-243 (28/01/14 23:39:27) (Detached)
2063..192-168-7-243 (28/01/14 23:39:27) (Detached)

here's some of the output of 2069:

Code:

JOB 145 PROCESSED 0.005 sec [nonces:0 errors:368 spi:48 miso:67 dup:0] (queue:0)
JOB 146 PROCESSED 0.006 sec [nonces:0 errors:366 spi:51 miso:67 dup:0] (queue:0)
JOB 147 PROCESSED 0.011 sec [nonces:0 errors:427 spi:50 miso:67 dup:0] (queue:0)
JOB 148 PROCESSED 0.003 sec [nonces:0 errors:276 spi:34 miso:68 dup:0] (queue:0)
JOB 149 PROCESSED 0.002 sec [nonces:0 errors:121 spi:27 miso:56 dup:0] (queue:0)
JOB 150 PROCESSED 0.005 sec [nonces:0 errors:357 spi:42 miso:65 dup:0] (queue:0)
JOB 151 PROCESSED 0.007 sec [nonces:0 errors:484 spi:33 miso:64 dup:0] (queue:0)
JOB 152 PROCESSED 0.005 sec [nonces:0 errors:394 spi:21 miso:68 dup:0] (queue:0)
JOB 153 PROCESSED 0.007 sec [nonces:0 errors:548 spi:55 miso:61 dup:2] (queue:0)
JOB 154 PROCESSED 0.005 sec [nonces:0 errors:426 spi:57 miso:60 dup:0] (queue:0)
JOB 155 PROCESSED 0.006 sec [nonces:0 errors:524 spi:40 miso:68 dup:2] (queue:0)
JOB 156 PROCESSED 0.005 sec [nonces:0 errors:382 spi:52 miso:65 dup:0] (queue:0)
JOB 157 PROCESSED 0.006 sec [nonces:0 errors:373 spi:41 miso:63 dup:0] (queue:0)
JOB 158 PROCESSED 0.004 sec [nonces:0 errors:357 spi:11 miso:58 dup:0] (queue:0)
JOB 159 PROCESSED 0.006 sec [nonces:0 errors:420 spi:56 miso:64 dup:0] (queue:0)

and some of 2063:

Code:

2014-01-28 23:43:18,070 INFO proxy getwork_listener._on_authorized # Worker '243' asks for new work
2014-01-28 23:43:19,099 INFO proxy getwork_listener._on_authorized # Worker '243' asks for new work
2014-01-28 23:43:20,026 INFO proxy getwork_listener._on_authorized # Worker '243' asks for new work
2014-01-28 23:43:21,051 INFO proxy getwork_listener._on_authorized # Worker '243' asks for new work
2014-01-28 23:43:22,077 INFO proxy getwork_listener._on_authorized # Worker '243' asks for new work
2014-01-28 23:43:23,104 INFO proxy getwork_listener._on_authorized # Worker '243' asks for new work
2014-01-28 23:43:24,031 INFO proxy getwork_listener._on_authorized # Worker '243' asks for new work
2014-01-28 23:43:25,057 INFO proxy getwork_listener._on_authorized # Worker '243' asks for new work
2014-01-28 23:43:26,084 INFO proxy getwork_listener._on_authorized # Worker '243' asks for new work
2014-01-28 23:43:27,109 INFO proxy getwork_listener._on_authorized # Worker '243' asks for new work
2014-01-28 23:43:28,035 INFO proxy getwork_listener._on_authorized # Worker '243' asks for new work
2014-01-28 23:43:29,061 INFO proxy getwork_listener._on_authorized # Worker '243' asks for new work
2014-01-28 23:43:30,088 INFO proxy getwork_listener._on_authorized # Worker '243' asks for new work
2014-01-28 23:44:06,631 DEBUG protocol protocol.lineReceived # > {u'params': [u'37f1', u'88e467b50f54143fe5be3226344ec74608e47c53696c43740000000000000000', u'01000000010000000000000000000000000000000000000000000000000000000000000000ffffffff2703495104062f503253482f04eb40e85208', u'0d2f7374726174756d506f6f6c2f00000000015d1fe595000000001976a9141157b2fc397d2cf3161313d220017d0dba368db588ac00000000', [u'3f23b91dd29e182079db07b2ba415833c38118042b59ce5b212fca23d27092de', u'66dd511b2faf371bb39c8d93932d028117a97d5295a969757ce7a18bacfd5773', u'9d880202be148bc6c31caddc7562a36ea29676a3fde0200926fd39eae9a2f578', u'0c6d9ee7f9d8854354660349dd09689810db94e36e83d266f767f55267b02642', u'60797fb71da5a528d5244dec03eef24a83006f15eb4f82077de8d048d4c198ac', u'9fd0193634d5b229f850792b0fdebabfc359b5818e01710bed9174002f62a8ca', u'a07dadf4444bda448cc6db75f4060857cae3e0cf04b3bf465876caeb77a88844', u'cccc0a87384a359e2e019f4cb5857c7436c4f599834fb9bd245ddc7f834755b2', u'b8017af8253690aba7b706cfbaa635cc30d4e12736ff8a4518173d713470a8b2', u'bdb8e2711c4a3755bbb36127598da1af92e671ad568928273bbd8177a24fc398'], u'00000002', u'1901f52c', u'52e840e3', False], u'id': None, u'method': u'mining.notify'}
2014-01-28 23:44:06,634 INFO proxy client_service.handle_event # New job 37f1 for prevhash 88e467b5, clean_jobs=False

Keefe

hero member

Activity: 681

Merit: 500

Quote from: cypherdoc on January 28, 2014, 04:32:13 PM

ok, now it's happening to me; again.

absolutely no hashing with one of my 14 card rigs. changed out SD cards and raspi. can login into admin page but no hashing. took rig apart and checked for any burnt boards (none) and blew out M board connector in case of excess oxidation (none apparent).

what were all the suggestions given for this frequent problem?

I've said it many times before, so I'll let you scroll up for details, but you need to check the output of chainminer and the proxies.

cypherdoc

legendary

Activity: 1764

Merit: 1002

ok, now it's happening to me; again.

absolutely no hashing with one of my 14 card rigs. changed out SD cards and raspi. can login into admin page but no hashing. took rig apart and checked for any burnt boards (none) and blew out M board connector in case of excess oxidation (none apparent).

what were all the suggestions given for this frequent problem?

CCCrypto

newbie

Activity: 28

Merit: 0

Quote from: zurg on January 27, 2014, 06:52:19 AM

I tried the card just by itself and actually changed it's position in the chain.
Didn't matter where I placed it, as any card after it was not showing at all. (including this card)

Okay, thanks. That will be helpful to remember for future troubleshooting.

zurg

hero member

Activity: 826

Merit: 500

Crypto Investor ;) @ Farmed Account Hunter

Quote from: CCCrypto on January 27, 2014, 05:32:06 PM

Quote from: zurg on January 27, 2014, 10:47:00 AM

Quote from: tom99 on January 27, 2014, 09:49:26 AM

Quote from: zurg on January 27, 2014, 06:52:19 AM

Ok guys, I need some assistance

I had an August kit with 2 boards (~47Gh/s)
so the M-Board is V1.0
on Friday I got 10 more boards and placed them 1st in-line then added my 2 pre-existing boards with last board being EOL one.
All this was powered by a 1Kw PS that died on me Sunday evening.
So I had it running about 48 hours.
All the new boards are stock = not overclocked.

Now I placed a spare 430W PS on the BF rig and it runs, however I can only see 96 chips running = 1st 6 cards.

Any ideas why it doesn't see the rest?

Thanks

you can do test on pcb that mboard did not see if it's working ok by itself.

Looks likew the card ain't working Sad

RMA time

What test did you do to determine the card wasn't working?

I tried the card just by itself and actually changed it's position in the chain.
Didn't matter where I placed it, as any card after it was not showing at all. (including this card)

CCCrypto

newbie

Activity: 28

Merit: 0

Quote from: zurg on January 27, 2014, 10:47:00 AM

Quote from: tom99 on January 27, 2014, 09:49:26 AM

Quote from: zurg on January 27, 2014, 06:52:19 AM

Ok guys, I need some assistance

I had an August kit with 2 boards (~47Gh/s)
so the M-Board is V1.0
on Friday I got 10 more boards and placed them 1st in-line then added my 2 pre-existing boards with last board being EOL one.
All this was powered by a 1Kw PS that died on me Sunday evening.
So I had it running about 48 hours.
All the new boards are stock = not overclocked.

Now I placed a spare 430W PS on the BF rig and it runs, however I can only see 96 chips running = 1st 6 cards.

Any ideas why it doesn't see the rest?

Thanks

you can do test on pcb that mboard did not see if it's working ok by itself.

Looks like the card ain't working Sad

RMA time

What test did you do to determine the card wasn't working?

zurg

hero member

Activity: 826

Merit: 500

Crypto Investor ;) @ Farmed Account Hunter

Quote from: tom99 on January 27, 2014, 09:49:26 AM

Quote from: zurg on January 27, 2014, 06:52:19 AM

Ok guys, I need some assistance

I had an August kit with 2 boards (~47Gh/s)
so the M-Board is V1.0
on Friday I got 10 more boards and placed them 1st in-line then added my 2 pre-existing boards with last board being EOL one.
All this was powered by a 1Kw PS that died on me Sunday evening.
So I had it running about 48 hours.
All the new boards are stock = not overclocked.

Now I placed a spare 430W PS on the BF rig and it runs, however I can only see 96 chips running = 1st 6 cards.

Any ideas why it doesn't see the rest?

Thanks

you can do test on pcb that mboard did not see if it's working ok by itself.

Looks like the card ain't working Sad

RMA time

tom99

sr. member

Activity: 420

Merit: 250

Quote from: zurg on January 27, 2014, 06:52:19 AM

Ok guys, I need some assistance

I had an August kit with 2 boards (~47Gh/s)
so the M-Board is V1.0
on Friday I got 10 more boards and placed them 1st in-line then added my 2 pre-existing boards with last board being EOL one.
All this was powered by a 1Kw PS that died on me Sunday evening.
So I had it running about 48 hours.
All the new boards are stock = not overclocked.

Now I placed a spare 430W PS on the BF rig and it runs, however I can only see 96 chips running = 1st 6 cards.

Any ideas why it doesn't see the rest?

Thanks

you can do test on pcb that mboard did not see if it's working ok by itself.

tom99

sr. member

Activity: 420

Merit: 250

Quote from: zurg on January 27, 2014, 07:46:32 AM

Quote from: KNK on January 27, 2014, 07:35:29 AM

Quote from: zurg on January 27, 2014, 07:20:59 AM

Upon inspecting the card
https://www.dropbox.com/s/sg34hw5u2v4y8rj/2014-01-27%2007.12.17.jpg
Look at the pins above C441 and C44E
The pins are shorted (or whatever the terms for that is)
Upon further inspecting the card at last 4 chips have solder across 2 pads like that.

Those pads are power (VDD) and are internally shorted anyway, so that's not the problem.
If (for the same chip U44) the pins on the left (with no caps) are shorted, then that may be a problem.

So when I look at the board with chips facing me and the writing is upright, the flow is going from the left to the right side and those cant be shorted, right?

https://www.dropbox.com/s/amopg7o7ec362ii/2014-01-27%2007.40.52.jpg
(Where the arrows are pointing)
https://www.dropbox.com/s/gy5rrxlk1dv4pci/2014-01-27%2007.41.25.jpg

dont worry all of them connect to grd.

edit: all start with Cxxx same and you can check with meter.

KNK

hero member

Activity: 692

Merit: 502

All of those are power.
Look at each chip with the white circle (on the board near the chip corner - that's pin 1 mark) at top right.

zurg

hero member

Activity: 826

Merit: 500

Crypto Investor ;) @ Farmed Account Hunter

Quote from: KNK on January 27, 2014, 07:35:29 AM

Quote from: zurg on January 27, 2014, 07:20:59 AM

Upon inspecting the card
https://www.dropbox.com/s/sg34hw5u2v4y8rj/2014-01-27%2007.12.17.jpg
Look at the pins above C441 and C44E
The pins are shorted (or whatever the terms for that is)
Upon further inspecting the card at last 4 chips have solder across 2 pads like that.

Those pads are power (VDD) and are internally shorted anyway, so that's not the problem.
If (for the same chip U44) the pins on the left (with no caps) are shorted, then that may be a problem.

So when I look at the board with chips facing me and the writing is upright, the flow is going from the left to the right side and those cant be shorted, right?

https://www.dropbox.com/s/amopg7o7ec362ii/2014-01-27%2007.40.52.jpg
(Where the arrows are pointing)
https://www.dropbox.com/s/gy5rrxlk1dv4pci/2014-01-27%2007.41.25.jpg

KNK

hero member

Activity: 692

Merit: 502

Quote from: zurg on January 27, 2014, 07:20:59 AM

Upon inspecting the card
https://www.dropbox.com/s/sg34hw5u2v4y8rj/2014-01-27%2007.12.17.jpg
Look at the pins above C441 and C44E
The pins are shorted (or whatever the terms for that is)
Upon further inspecting the card at last 4 chips have solder across 2 pads like that.

Those pads are power (VDD) and are internally shorted anyway, so that's not the problem.
If (for the same chip U44) the pins on the left (with no caps) are shorted, then that may be a problem.

zurg

hero member

Activity: 826

Merit: 500

Crypto Investor ;) @ Farmed Account Hunter

Quote from: BenTuras on January 27, 2014, 06:58:47 AM

Quote from: zurg on January 27, 2014, 06:52:19 AM

Ok guys, I need some assistance

I had an August kit with 2 boards (~47Gh/s)
so the M-Board is V1.0
on Friday I got 10 more boards and placed them 1st in-line then added my 2 pre-existing boards with last board being EOL one.
All this was powered by a 1Kw PS that died on me Sunday evening.
So I had it running about 48 hours.
All the new boards are stock = not overclocked.

Now I placed a spare 430W PS on the BF rig and it runs, however I can only see 96 chips running = 1st 6 cards.

Any ideas why it doesn't see the rest?

Thanks

First check if the boards are still OK by running 6 boards at a time. Do this for the other 6 boards too.
Then add 1 board at a time till you get issues.
Looks like a PSU problem. 430W is probably not enough for 12 boards.
Also try to spread your boards. Skip positions on the M-board.
Its ok to run XXXO-XXOX-XOXO-XXXX for example, X being a board.
(Some will say the boards need to be adjacent, but I have an M-board running with skipped positions without problems).

Ok, here is an update.
I tried a 480W PS no change, I opened a new 1KW PS and no change.
I shutdown the miner and yanked the card #7 and moved the rest up the chain.
Miner is UP with 168 chips showing which is what it's supposed to be in my case with this 1 card out of it.

Upon inspecting the card
https://www.dropbox.com/s/sg34hw5u2v4y8rj/2014-01-27%2007.12.17.jpg
Look at the pins above C441 and C44E
The pins are shorted (or whatever the terms for that is)
Upon further inspecting the card at last 4 chips have solder across 2 pads like that.

BenTuras

hero member

Activity: 826

Merit: 1001

Quote from: zurg on January 27, 2014, 06:52:19 AM

Ok guys, I need some assistance

I had an August kit with 2 boards (~47Gh/s)
so the M-Board is V1.0
on Friday I got 10 more boards and placed them 1st in-line then added my 2 pre-existing boards with last board being EOL one.
All this was powered by a 1Kw PS that died on me Sunday evening.
So I had it running about 48 hours.
All the new boards are stock = not overclocked.

Now I placed a spare 430W PS on the BF rig and it runs, however I can only see 96 chips running = 1st 6 cards.

Any ideas why it doesn't see the rest?

Thanks

First check if the boards are still OK by running 6 boards at a time. Do this for the other 6 boards too.
Then add 1 board at a time till you get issues.
Looks like a PSU problem. 430W is probably not enough for 12 boards.
Also try to spread your boards. Skip positions on the M-board.
Its ok to run XXXO-XXOX-XOXO-XXXX for example, X being a board.
(Some will say the boards need to be adjacent, but I have an M-board running with skipped positions without problems).

zurg

hero member

Activity: 826

Merit: 500

Crypto Investor ;) @ Farmed Account Hunter

Ok guys, I need some assistance

I had an August kit with 2 boards (~47Gh/s)
so the M-Board is V1.0
on Friday I got 10 more boards and placed them 1st in-line then added my 2 pre-existing boards with last board being EOL one.
All this was powered by a 1Kw PS that died on me Sunday evening.
So I had it running about 48 hours.
All the new boards are stock = not overclocked.

Now I placed a spare 430W PS on the BF rig and it runs, however I can only see 96 chips running = 1st 6 cards.

Any ideas why it doesn't see the rest?

Thanks

CCCrypto

newbie

Activity: 28

Merit: 0

Quote from: zurg on January 26, 2014, 09:29:02 AM

Quote from: CCCrypto on January 26, 2014, 09:26:43 AM

Quote from: zurg on January 25, 2014, 11:16:28 PM

Quote from: CCCrypto on January 25, 2014, 04:44:23 PM

Does anyone have advice on connecting to Bitminter via stratum proxy with a Bitfury rig?

I'm trying to connect using stratum+tcp://mint.bitminter.com (on the admin page), and the noncerate is just flashing 0GH/s. I can't figure it out.

mint.bitminter.com 3333 username_workername password

Sorry for the confusion, but do I put 'mint.bitminter.com' or 'stratum+tcp://mint.bitminter.com' on the Bitfury admin page?

Right now I'm using port 3333 along with stratum+tcp://mint.bitminter.com. The username and worker details appear to be correct as well. All other pools work fine (BTC Guild, Slush's Pool, etc.), but for some reason I can't connect to Bitminter.

just mint.bitminter.com

Yup, that was it. Thanks for your help.

zurg

hero member

Activity: 826

Merit: 500

Crypto Investor ;) @ Farmed Account Hunter

Quote from: CCCrypto on January 26, 2014, 09:26:43 AM

Quote from: zurg on January 25, 2014, 11:16:28 PM

Quote from: CCCrypto on January 25, 2014, 04:44:23 PM

Does anyone have advice on connecting to Bitminter via stratum proxy with a Bitfury rig?

I'm trying to connect using stratum+tcp://mint.bitminter.com (on the admin page), and the noncerate is just flashing 0GH/s. I can't figure it out.

mint.bitminter.com 3333 username_workername password

Sorry for the confusion, but do I put 'mint.bitminter.com' or 'stratum+tcp://mint.bitminter.com' on the Bitfury admin page?

Right now I'm using port 3333 along with stratum+tcp://mint.bitminter.com. The username and worker details appear to be correct as well. All other pools work fine (BTC Guild, Slush's Pool, etc.), but for some reason I can't connect to Bitminter.

just mint.bitminter.com

CCCrypto

newbie

Activity: 28

Merit: 0

Quote from: zurg on January 25, 2014, 11:16:28 PM

Quote from: CCCrypto on January 25, 2014, 04:44:23 PM

Does anyone have advice on connecting to Bitminter via stratum proxy with a Bitfury rig?

I'm trying to connect using stratum+tcp://mint.bitminter.com (on the admin page), and the noncerate is just flashing 0GH/s. I can't figure it out.

mint.bitminter.com 3333 username_workername password

Sorry for the confusion, but do I put 'mint.bitminter.com' or 'stratum+tcp://mint.bitminter.com' on the Bitfury admin page?

Right now I'm using stratum+tcp://mint.bitminter.com along with port 3333. The username and worker details appear to be correct as well. All other pools work fine (BTC Guild, Slush's Pool, etc.), but for some reason I can't connect to Bitminter.

zurg

hero member

Activity: 826

Merit: 500

Crypto Investor ;) @ Farmed Account Hunter

Quote from: jddebug on January 25, 2014, 11:26:34 PM

Quote from: zurg on January 25, 2014, 11:16:28 PM

Quote from: CCCrypto on January 25, 2014, 04:44:23 PM

Does anyone have advice on connecting to Bitminter via stratum proxy with a Bitfury rig?

I'm trying to connect using stratum+tcp://mint.bitminter.com (on the admin page), and the noncerate is just flashing 0GH/s. I can't figure it out.

mint.binminter.com 3333 username_workername password

binminter?

I guess it's bed time, lol

Topic: [GUIDE] BitFury Miner Support/Tuning - page 6. (Read 148062 times)