Topic: [Guide] Dogie's Comprehensive ASICMiner Blade Setup - page 5. (Read 580771 times)
Post a pic of your blade config page, a cmd window with ipconfig /all and your proxy
changed server address to
192.168.1.146,192.168.1.146
Still not getting anything
192.168.1.146,192.168.1.146
Still not getting anything
Server IP is wrong, I highly doubt your computer is at 127.0.0.1
I can't seem to get it to work. I tried slush's and weminecrypto and still no good. My network lights are steady orange and flashing green
Total MHS: 00000
Received: 0000000000
Accepted: 0000000000
Per Minute: 000.00
Efficiency: 000.00%
Up Time: 0d,00h,00m,45s
Current Server: 127.0.0.1:8334
Chip: OOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO
IP 192.168.1.254
Mask 255.255.255.0
Gateway 192.168.1.1
WEB Port 8000
Primary DNS 192.168.1.1
Secondary DNS 192.168.1.1
Ports 8334,8334
Server addresses 127.0.0.1,127.0.0.1
user:pass ****.****:****
Any ideas?
Total MHS: 00000
Received: 0000000000
Accepted: 0000000000
Per Minute: 000.00
Efficiency: 000.00%
Up Time: 0d,00h,00m,45s
Current Server: 127.0.0.1:8334
Chip: OOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO
IP 192.168.1.254
Mask 255.255.255.0
Gateway 192.168.1.1
WEB Port 8000
Primary DNS 192.168.1.1
Secondary DNS 192.168.1.1
Ports 8334,8334
Server addresses 127.0.0.1,127.0.0.1
user:pass ****.****:****
Any ideas?
I have had a blade hooked up for a week now and all has been running fine then yesterday it could not be found by bfgminer even though the ports appear correct in both. I checked everything. I tried all my different mining pools I use and if I do get one to connect I get very low hash around 33.6mh's and 333 mh/s.
I changed nothing on either end it just quit working properly.
I have my blade setup to point to my bfgminer that connects to my pools
Here is my .bat file
cd c:\
C:\bfgminer2\bfgminer.exe --http-port 8334 -S erupter:all -o stratum+tcp://ispace.co.uk:3346 -O somename.asic2:password
That is all I ever ran to get everything to work.
When I tried to connect somewhere that uses the old getwork everything was fine and it runs as it should.
What am I doing wrong or what has changed.
All chips show 0 no X's at all!
I would be willing to do team viewer with someone later also
Any help greatly appreciated!
Try slush's proxy. I changed nothing on either end it just quit working properly.
I have my blade setup to point to my bfgminer that connects to my pools
Here is my .bat file
cd c:\
C:\bfgminer2\bfgminer.exe --http-port 8334 -S erupter:all -o stratum+tcp://ispace.co.uk:3346 -O somename.asic2:password
That is all I ever ran to get everything to work.
When I tried to connect somewhere that uses the old getwork everything was fine and it runs as it should.
What am I doing wrong or what has changed.
All chips show 0 no X's at all!
I would be willing to do team viewer with someone later also
Any help greatly appreciated!
I have had a blade hooked up for a week now and all has been running fine then yesterday it could not be found by bfgminer even though the ports appear correct in both. I checked everything. I tried all my different mining pools I use and if I do get one to connect I get very low hash around 33.6mh's and 333 mh/s.
I changed nothing on either end it just quit working properly.
I have my blade setup to point to my bfgminer that connects to my pools
Here is my .bat file
cd c:\
C:\bfgminer2\bfgminer.exe --http-port 8334 -S erupter:all -o stratum+tcp://ispace.co.uk:3346 -O somename.asic2:password
That is all I ever ran to get everything to work.
When I tried to connect somewhere that uses the old getwork everything was fine and it runs as it should.
What am I doing wrong or what has changed.
All chips show 0 no X's at all!
I would be willing to do team viewer with someone later also
Any help greatly appreciated!
I changed nothing on either end it just quit working properly.
I have my blade setup to point to my bfgminer that connects to my pools
Here is my .bat file
cd c:\
C:\bfgminer2\bfgminer.exe --http-port 8334 -S erupter:all -o stratum+tcp://ispace.co.uk:3346 -O somename.asic2:password
That is all I ever ran to get everything to work.
When I tried to connect somewhere that uses the old getwork everything was fine and it runs as it should.
What am I doing wrong or what has changed.
All chips show 0 no X's at all!
I would be willing to do team viewer with someone later also
Any help greatly appreciated!
Updated design to fit with newer guides and removed donation address
I am having a problem and was wondering if anyone could help. I have a blade v2 green board that has been running fine for over a week. I noticed a drop in hash rate in my pool so I check the config page and it wont stay connected to a server. It keeps switching back and forth between my two server IP's. I am using BFGminer proxy and have tried different versions, different machines, wired/wireless, changing the IP and port of the blade and a hardware reset, but to no avail. Anyone have an issue like this before?
Have you tried slush's proxy?
I am having a problem and was wondering if anyone could help. I have a blade v2 green board that has been running fine for over a week. I noticed a drop in hash rate in my pool so I check the config page and it wont stay connected to a server. It keeps switching back and forth between my two server IP's. I am using BFGminer proxy and have tried different versions, different machines, wired/wireless, changing the IP and port of the blade and a hardware reset, but to no avail. Anyone have an issue like this before?
Dogie,
Thanks for all of the useful info. The good news is that I was finally able to access the config page. The bad news is there are all x's for the chip status. The board is currently being powered by a backplane. In this case, would you consider all x's the kiss of death?
Thanks again for all of your support.
Try powering it independently. If your PSU and wiring is all good, then yes. Talk to your reseller. Thanks for all of the useful info. The good news is that I was finally able to access the config page. The bad news is there are all x's for the chip status. The board is currently being powered by a backplane. In this case, would you consider all x's the kiss of death?
Thanks again for all of your support.
Dogie,
Thanks for all of the useful info. The good news is that I was finally able to access the config page. The bad news is there are all x's for the chip status. The board is currently being powered by a backplane. In this case, would you consider all x's the kiss of death?
Thanks again for all of your support.
Thanks for all of the useful info. The good news is that I was finally able to access the config page. The bad news is there are all x's for the chip status. The board is currently being powered by a backplane. In this case, would you consider all x's the kiss of death?
Thanks again for all of your support.
I've been very busy later and I just got around to trying some fixes. After messing around with my blades some more today I got the factory reset to work... I think. I used a pin and held it on the factory reset switches until the green light came on an blinked. I did this to both of them. However I still cannot access them through my browser. I assume they would be switched to 192.168.1.254:8000 but it still doesn't work. I am doing this with them 1 at a time. I will not have both plugged in at once until I get this straightened out.
Are you sure your router is on 192.168.1.x?
I've been very busy later and I just got around to trying some fixes. After messing around with my blades some more today I got the factory reset to work... I think. I used a pin and held it on the factory reset switches until the green light came on an blinked. I did this to both of them. However I still cannot access them through my browser. I assume they would be switched to 192.168.1.254:8000 but it still doesn't work. I am doing this with them 1 at a time. I will not have both plugged in at once until I get this straightened out.
I can't confirm that is the issue but the fuse is shown in red in this picture.
You can find replacement fuses at any auto parts supply store, Walmart, etc.
Bring the old fuse with you when you go.
Thank you. I should have mentioned that I have a ASICMiner Blade V2. It doesn't have a fuse like that. Instead of connecting it to the Backplane with the Blade heat sink facing the power supply, I did the opposite. The blade heat sink was pointing away from the PSU.
I wish it had one like that.
I can't confirm that is the issue but the fuse is shown in red in this picture.
http://i.imgur.com/wXatUAl.jpg
You can find replacement fuses at any auto parts supply store, Walmart, etc.
Bring the old fuse with you when you go.
Thank you. I should have mentioned that I have a ASICMiner Blade V2. It doesn't have a fuse like that. Instead of connecting it to the Backplane with the Blade heat sink facing the power supply, I did the opposite. The blade heat sink was pointing away from the PSU.
I wish it had one like that.
Thank you for your reply. Could you possibly tell me how to locate and replace the fuse on an ASICMiner Blade? Is there a guide somewhere?
Thanks.
Thanks.
I can't confirm that is the issue but the fuse is shown in red in this picture.
You can find replacement fuses at any auto parts supply store, Walmart, etc.
Bring the old fuse with you when you go.
Try a new fuse, else it's gg unfortunately.
Thank you for your reply. Could you possibly tell me how to locate and replace the fuse on an ASICMiner Blade? Is there a guide somewhere?
Thanks.
Hello Dogie
I need your help. I mistakenly install my ASICMiner blades in wrong polarity. Now all of my blades will not work. Is there anything I can do to fix them? I have tried resetting them to factory setting but the green lights will not come on when I turn on the power supply. I really don't know what I was thing when I took the blades out.
Regards
I need your help. I mistakenly install my ASICMiner blades in wrong polarity. Now all of my blades will not work. Is there anything I can do to fix them? I have tried resetting them to factory setting but the green lights will not come on when I turn on the power supply. I really don't know what I was thing when I took the blades out.
Regards
Try a new fuse, else it's gg unfortunately.
Hello Dogie
I need your help. I mistakenly install my ASICMiner blades in wrong polarity. Now all of my blades will not work. Is there anything I can do to fix them? I have tried resetting them to factory setting but the green lights will not come on when I turn on the power supply. I really don't know what I was thing when I took the blades out.
Regards
I need your help. I mistakenly install my ASICMiner blades in wrong polarity. Now all of my blades will not work. Is there anything I can do to fix them? I have tried resetting them to factory setting but the green lights will not come on when I turn on the power supply. I really don't know what I was thing when I took the blades out.
Regards
I have tried unplugging all of my blades and cubes from the network before trying to access the config page of the blade I'm having trouble with. Unfortunately the blade is not being recognized by my router, but the green and yellow lights are blinking on the Ethernet port. Thanks in advance for your assistance.
I tried setting this up through a wireless connection before and it didn't work. for me, I needed to have a comp hard wired to my connection because my wireless router was preventing me from connecting (somehow)
I'm not sure what your setup is but I thought I was doing everything right (which is turned out I wasn't lol) but I would have been trying for days before thinking about trying from a hard wired laptop.. thanks for the tip @demonmaestro
you'll get it sorted, people on here are really nice and helpful. don't get discouraged and don't give up. if you can't figure it out, well dl teamviewer and get someone from here to help you. That's what I did haha
good luck!
Jump to: