[Guide] Dogie's Comprehensive ASICMiner Blade Setup - page 8.

dogie

legendary

Activity: 1666

Merit: 1185

dogiecoin.com

Quote from: alwaysthirsty on February 09, 2014, 04:41:28 PM

Quote from: dogie on February 09, 2014, 01:26:28 PM

Quote from: alwaysthirsty on February 09, 2014, 01:22:14 PM

I need help guys, after hashinh for several days my cables at the molex splitters started melting. Huh

See the OP again, the recommendations is NOT to use a molex connector. Plenty of links and information there.

It would power ONE. Remember you can use the 4 pin ATX mobo cable for one, and if you have am 8 pin you can power two with 2x4 pin.
Thank you for all the hard work and effort you have put in the OP. Do you think that, cutting a 6pin connector would be sufficient to power 3 blades, as a replacement for the molex?

alwaysthirsty

newbie

Activity: 13

Merit: 0

Quote from: dogie on February 09, 2014, 01:26:28 PM

Quote from: alwaysthirsty on February 09, 2014, 01:22:14 PM

I need help guys, after hashinh for several days my cables at the molex splitters started melting. Huh

See the OP again, the recommendations is NOT to use a molex connector. Plenty of links and information there.

Thank you for all the hard work and effort you have put in the OP. Do you think that, cutting a 6pin connector would be sufficient to power 3 blades, as a replacement for the molex?

Datelli

newbie

Activity: 19

Merit: 0

I'm mining Dogy, all is set up now and in full working order. Thank you so much for your help. Really appriciated!

Michael

dogie

legendary

Activity: 1666

Merit: 1185

dogiecoin.com

Quote from: Datelli on February 09, 2014, 01:46:27 PM

Thanks Dogie, let me try that. :-) However I dont have the "Switch clock" button on my config screen. Would "Update/restart" do as well?

You won't on V2s, they can't be overclocked.

Datelli

newbie

Activity: 19

Merit: 0

Thanks Dogie, let me try that. :-) However I dont have the "Switch clock" button on my config screen. Would "Update/restart" do as well?

dogie

legendary

Activity: 1666

Merit: 1185

dogiecoin.com

Quote from: Datelli on February 09, 2014, 01:35:53 PM

Hi ya'll

I'm almost there, just 2 problems to overcome, however they kept me busy this whole sunday. ;-)

I bought a bunch of ASIC V2 blades, when approaching them the configuration screen reads on both primary as secundary DNS 0.0.0.0
My -on this matter not so educated guess- would be this isn't right, right? Didn't find a solution or answer so far, hence this message.

The second problem I ran into is the BFGminer, in big red characters it screams at me: NO DEVICES FOUND: press 'M' and '+' to add
Now I'm wondering if my DNS settings might have something to do with this.

Any help is HIGHLY appriciated, to be honest... I'm pretty desperated. Almost like him: http://www.youtube.com/watch?v=XAgyR9Gwcp0 (xept for the remote control action) or him: http://www.youtube.com/watch?v=KImHU9TGOfU

Haha :-) No really, I don't have the specific knowledge to solve this, so any help would be very helpfull, thanks in advance!

Michael

Ignore the DNS field, its not required.

Use the stratum proxy, its 10x simpler than using BFG miner as the proxy. Instructions are in the OP.

Datelli

newbie

Activity: 19

Merit: 0

Hi ya'll

I'm almost there, just 2 problems to overcome, however they kept me busy this whole sunday. ;-)

I bought a bunch of ASIC V2 blades, when approaching them the configuration screen reads on both primary as secundary DNS 0.0.0.0
My -on this matter not so educated guess- would be this isn't right, right? Didn't find a solution or answer so far, hence this message.

The second problem I ran into is the BFGminer, in big red characters it screams at me: NO DEVICES FOUND: press 'M' and '+' to add
Now I'm wondering if my DNS settings might have something to do with this.

Any help is HIGHLY appriciated, to be honest... I'm pretty desperated. Almost like him: http://www.youtube.com/watch?v=XAgyR9Gwcp0 (xept for the remote control action) or him: http://www.youtube.com/watch?v=KImHU9TGOfU

Haha :-) No really, I don't have the specific knowledge to solve this, so any help would be very helpfull, thanks in advance!

Michael

dogie

legendary

Activity: 1666

Merit: 1185

dogiecoin.com

Quote from: alwaysthirsty on February 09, 2014, 01:22:14 PM

I need help guys, after hashinh for several days my cables at the molex splitters started melting. Huh

See the OP again, the recommendations is NOT to use a molex connector. Plenty of links and information there.

alwaysthirsty

newbie

Activity: 13

Merit: 0

I need help guys, after hashinh for several days my cables at the molex splitters started melting. Huh

dogie

legendary

Activity: 1666

Merit: 1185

dogiecoin.com

OP has been updated with new PSUs, fan controllers, fans and more information.

dogie

legendary

Activity: 1666

Merit: 1185

dogiecoin.com

Quote from: xkelvinchiax on January 25, 2014, 02:03:30 AM

HELP?

http://www.coolermaster.com/powersupply/gxii-series/gxii-650w/ <-- can this cube overclock to HIGH MODE?

Ask cube stuff in the cube thread please. But yes.

Datelli

newbie

Activity: 19

Merit: 0

Matt & Mike,

thanks for your help and swift reply, much appriciated!

Cheers,

Michael

MikeMike

legendary

Activity: 2254

Merit: 1020

★ Ⓚ KORE TEAM Ⓚ ★

Quote from: Datelli on February 07, 2014, 11:52:21 AM

Hi ya'll

I wonder, does anyone know how to reset the V2 blades to factory default?

Thanks,

Michael

http://www.freeimagehosting.net/w797k

matt4054

legendary

Activity: 1946

Merit: 1035

Quote from: Datelli on February 07, 2014, 11:52:21 AM

I wonder, does anyone know how to reset the V2 blades to factory default?

You need to short "pins" (actually holes on V2) 2 and 3 just on the right of the Ethernet connector.
If you look at the PCB it should be written 'Factory Reset' on it, next to these pins

Datelli

newbie

Activity: 19

Merit: 0

Hi ya'll

I wonder, does anyone know how to reset the V2 blades to factory default?

Thanks,

Michael

dogie

legendary

Activity: 1666

Merit: 1185

dogiecoin.com

Quote from: NL5 on February 05, 2014, 07:19:23 PM

I have a v1 blade and I am looking for some information on overclocking it.
When I overclock the board it actually slows down the hash rate from 10 to about 8ghz. All of the chips show fine .
I have scoured the internet for information about this but have so far come up empty. Is this potentially a voltage issue? The board is running cool to the touch, so I would not think it a heat issue.
This is the only blade on a 400watt power supply.

Any insight would be appreciated.

Thank you,

Either voltage or power issues. Probably maxing out the cable.

NL5

newbie

Activity: 2

Merit: 0

I have a v1 blade and I am looking for some information on overclocking it.
When I overclock the board it actually slows down the hash rate from 10 to about 8ghz. All of the chips show fine .
I have scoured the internet for information about this but have so far come up empty. Is this potentially a voltage issue? The board is running cool to the touch, so I would not think it a heat issue.
This is the only blade on a 400watt power supply.

Any insight would be appreciated.

Thank you,

matt4054

legendary

Activity: 1946

Merit: 1035

Quote from: ShiNoDaX on February 04, 2014, 08:11:57 PM

hello all
big problem
after 2 hours yellow burned What is the solution ?

Was this a factory made (soldered) Molex connector or "home made"? I'm asking this because the naked end of the two 12V (yellow) wires seem to have been twisted together, it seems unusual to be, but I may be wrong or in may be the result / visual artefacts of melting. From personal experience, bare wires inserted straight into a PCI-e 6/8 pin or Molex connector almost ends up badly after a few days when not just hours. Generally it starts overheating, any traction on wires may cause short circuits - at best just sparks and PSU shutdown, possibly nastier. Meltdown with soot on wires with also occur after overheating becomes excessive.

It would be interesting to see how you had wired the other end too, on the Blade side.

ShiNoDaX

newbie

Activity: 8

Merit: 0

hello all
big problem
after 2 hours yellow burned What is the solution ?
http://www4.0zz0.com/2014/02/05/01/896401878.jpg

dogie

legendary

Activity: 1666

Merit: 1185

dogiecoin.com

Quote from: madcratebuilder on January 28, 2014, 12:33:53 PM

Quote from: matt4054 on January 27, 2014, 06:02:09 PM

Quote from: alwaysthirsty on January 27, 2014, 02:16:34 PM

I swapped the psu with my desktop psu, i got the status OOO but now it just restarts itself after ~2 minutes of doing nothing. The mining proxy seems to cause my OS to freeze every now and then

http://s14.postimg.org/cl9mpqqgv/Untitled.png

Any ideas? Huh

From another node on your network, you could attempt a TCP connection to 192.168.1.101:8332 just to make sure that nothing on either your network or OS or whatever is blocking incoming connections to your proxy. Otherwise, I can't see any reason, many people reported that Blades are *very* sensitive to network issues that are generally not causing problems to other devices.

I had intermittent problems using wifi with my Blades. I bought a used switch and hard wired, instant 10.8ghs and runs for days and days with out problem. Using Pi with bfgminer proxy.

+1 to random network topology problems

Topic: [Guide] Dogie's Comprehensive ASICMiner Blade Setup - page 8. (Read 580771 times)