[Guide] Dogie's Comprehensive Bitmain AntMiner S1 Setup [HD] - page 32.

dogie

legendary

Activity: 1666

Merit: 1185

dogiecoin.com

Quote from: arorts on December 10, 2013, 04:10:59 AM

Quote from: klondike_bar on December 09, 2013, 11:56:46 PM

Quote from: arorts on December 09, 2013, 11:19:11 PM

Mine is only hashing half!! (90 Gh/s). Any reasons why??? What's going on???

whats your miner status show? does one of the boards show the chips as 'x'-es, or is only 1 board visible?

I just figured that the control cable set was disconnected so I plugged it in and it enabled the other board.
However, my main problem remains that I can no longer access the WAN interface after I mistakenly set it as DHCP. I hadn't enabled WiFi so it's not getting any address from my Wifi either.

Any way to access it? reset it?

Thanks,

Did you have any luck?

dogie

legendary

Activity: 1666

Merit: 1185

dogiecoin.com

Quote from: arorts on December 10, 2013, 04:10:59 AM

Quote from: klondike_bar on December 09, 2013, 11:56:46 PM

Quote from: arorts on December 09, 2013, 11:19:11 PM

Mine is only hashing half!! (90 Gh/s). Any reasons why??? What's going on???

whats your miner status show? does one of the boards show the chips as 'x'-es, or is only 1 board visible?

I just figured that the control cable set was disconnected so I plugged it in and it enabled the other board.
However, my main problem remains that I can no longer access the WAN interface after I mistakenly set it as DHCP. I hadn't enabled WiFi so it's not getting any address from my Wifi either.

Any way to access it? reset it?

Thanks,

Check your router to see if its been assigned an IP you weren't aware of.

arorts

sr. member

Activity: 408

Merit: 250

Quote from: klondike_bar on December 09, 2013, 11:56:46 PM

Quote from: arorts on December 09, 2013, 11:19:11 PM

Mine is only hashing half!! (90 Gh/s). Any reasons why??? What's going on???

whats your miner status show? does one of the boards show the chips as 'x'-es, or is only 1 board visible?

I just figured that the control cable set was disconnected so I plugged it in and it enabled the other board.
However, my main problem remains that I can no longer access the WAN interface after I mistakenly set it as DHCP. I hadn't enabled WiFi so it's not getting any address from my Wifi either.

Any way to access it? reset it?

Thanks,

klondike_bar

legendary

Activity: 2128

Merit: 1005

ASIC Wannabe

Quote from: arorts on December 09, 2013, 11:19:11 PM

Mine is only hashing half!! (90 Gh/s). Any reasons why??? What's going on???

whats your miner status show? does one of the boards show the chips as 'x'-es, or is only 1 board visible?

arorts

sr. member

Activity: 408

Merit: 250

Mine is only hashing half!! (90 Gh/s). Any reasons why??? What's going on???

xstr8guy

hero member

Activity: 784

Merit: 1004

Glow Stick Dance!

Quote from: xstr8guy on December 09, 2013, 07:29:00 PM

Forgive my ignorance but why would it be that I can't access my miner by entering the IP address in my browser? The sticker is on the side and I double-checked with Advanced IP Scanner. I'm sure I just missing something simple. This bit from Dogie's guide confuses me though...

Quote

Make sure your router's subnet is 2, ie 192.168.2.x. This is just temporary.

What does that mean and how do I go about changing, if in fact I need to?

If anyone has the same problem, this thread here as more detailed directions on how to configure your router...
https://bitcointalksearch.org/topic/setup-troubleshoot-bitmain-antminer-s1-180ghs-miner-344970

sushi

full member

Activity: 238

Merit: 100

ASIC Myth Buster

SUSHI's AntMiner GROUP BUY 2

SHIPPS ON DECEMBER 12 & 13

150 Units Direct from Bitmain!

https://bitcointalksearch.org/topic/group-buy-clos-shipped-giveaway-bitmain-antminer-180-ghs-300-units-364342

Sorry, Dogie... let me list it here Grin

xstr8guy

hero member

Activity: 784

Merit: 1004

Glow Stick Dance!

Forgive my ignorance but why would it be that I can't access my miner by entering the IP address in my browser? The sticker is on the side and I double-checked with Advanced IP Scanner. I'm sure I just missing something simple. This bit from Dogie's guide confuses me though...

Quote

Make sure your router's subnet is 2, ie 192.168.2.x. This is just temporary.

What does that mean and how do I go about changing, if in fact I need to?

dogie

legendary

Activity: 1666

Merit: 1185

dogiecoin.com

Quote from: klondike_bar on December 09, 2013, 05:26:14 PM

Quote from: dogie on December 09, 2013, 02:16:04 PM

Quote from: AlexeyK on December 08, 2013, 06:01:38 AM

Hi All

just want to verify , miners with version 2 coming with Red$Black power connectors

Red for 12V and Black for ground ?

thanks

Do you have a picture?

i put a picture somewhere. basically the newer antminers dont have green scrw terminals - they are now red and black and also marked as + and GND

Ok ty

klondike_bar

legendary

Activity: 2128

Merit: 1005

ASIC Wannabe

Quote from: dogie on December 09, 2013, 02:16:04 PM

Quote from: AlexeyK on December 08, 2013, 06:01:38 AM

Hi All

just want to verify , miners with version 2 coming with Red$Black power connectors

Red for 12V and Black for ground ?

thanks

Do you have a picture?

i put a picture somewhere. basically the newer antminers dont have green scrw terminals - they are now red and black and also marked as + and GND

dogie

legendary

Activity: 1666

Merit: 1185

dogiecoin.com

Quote from: AlexeyK on December 08, 2013, 06:01:38 AM

Hi All

just want to verify , miners with version 2 coming with Red$Black power connectors

Red for 12V and Black for ground ?

thanks

Do you have a picture?

klondike_bar

legendary

Activity: 2128

Merit: 1005

ASIC Wannabe

Quote from: AlexeyK on December 08, 2013, 06:01:38 AM

Hi All

just want to verify , miners with version 2 coming with Red$Black power connectors

Red for 12V and Black for ground ?

thanks

correct. yellow 12V lines go to the red terminals

AlexeyK

full member

Activity: 182

Merit: 100

Hi All

just want to verify , miners with version 2 coming with Red$Black power connectors

Red for 12V and Black for ground ?

thanks

dogie

legendary

Activity: 1666

Merit: 1185

dogiecoin.com

Added pinout info to OP:

My cables are braided or aren't color coded: See below diagram for pin-outs.

dogie

legendary

Activity: 1666

Merit: 1185

dogiecoin.com

Quote from: joeventura on December 07, 2013, 09:35:50 AM

Even though I dont have one of these I must say you do a hell of a setup guide!!

Nicely done sir!!

Thanks

joeventura

hero member

Activity: 854

Merit: 500

Even though I dont have one of these I must say you do a hell of a setup guide!!

Nicely done sir!!

dogie

legendary

Activity: 1666

Merit: 1185

dogiecoin.com

Quote from: davecoin on December 07, 2013, 04:21:05 AM

Is there a trick to getting the antminer to hold on to a reassigned static ip?

I go into the Network > Interfaces > Wan > and change the settings to an address on 192.168.1.x that is unassigned on my network, but when I hit save and apply it just hangs. I've tried a few different times now, waiting 2 min, 5 min, 10 min, and after plugging the cable back into the router, the miner hasn't been reassigned to the new address. I used the advance ip scanner utility and it still shows the same default address at 192.168.2.xx, which I can now not connect to either. After shorting the pins to do a hard reset, I can re-connect again on 192.168.2.99.

Any ideas?

I dont remember this happening with Avalons. In the mean time you can do the reverse and set your router to keep giving the device the same IP - creating a static IP device out of a DCHP client. Alternatively, as long as the unit and router never turn off, its IP won't change.

dogie

legendary

Activity: 1666

Merit: 1185

dogiecoin.com

Quote from: alfabitcoin on December 07, 2013, 08:45:07 AM

Here is what I did:
Bought silent 12cm fan and mounted it on opposite side of the miner, with soaking hot air out. I powering it with molex from PDU (no need of PWM).
Also covered top of the first half miner where original fan is located.

Temp 37c (both blades)
hashing 184 ghs stock. avg 181ghs

Original fan rpm are low so miner is silent and stable.

Need some case and tweaking, can be a lot better.

Yep I've also recommended they add a shroud of some form - then the tunnel design works well.

alfabitcoin

sr. member

Activity: 476

Merit: 250

Here is what I did:
Bought silent 12cm fan and mounted it on opposite side of the miner, with soaking hot air out. I powering it with molex from PDU (no need of PWM).
Also covered top of the first half miner where original fan is located.

Temp 37c (both blades)
hashing 184 ghs stock. avg 181ghs

Original fan rpm are low so miner is silent and stable.

Need some case and tweaking, can be a lot better.

davecoin

hero member

Activity: 816

Merit: 1000

Is there a trick to getting the antminer to hold on to a reassigned static ip?

I go into the Network > Interfaces > Wan > and change the settings to an address on 192.168.1.x that is unassigned on my network, but when I hit save and apply it just hangs. I've tried a few different times now, waiting 2 min, 5 min, 10 min, and after plugging the cable back into the router, the miner hasn't been reassigned to the new address. I used the advance ip scanner utility and it still shows the same default address at 192.168.2.xx, which I can now not connect to either. After shorting the pins to do a hard reset, I can re-connect again on 192.168.2.99.

Any ideas?

Topic: [Guide] Dogie's Comprehensive Bitmain AntMiner S1 Setup [HD] - page 32. (Read 112395 times)