Topic: KanoPool kano.is lowest 0.9% fee 🐈 since 2014 - Worldwide - 2432 blocks - page 1268. (Read 5352429 times)
August 21, 2016, 07:49:18 AM
Way to go ROIER with 38.62THs hitting that last block! That would be his 2nd Kano block and our 1st of the day!
August 21, 2016, 07:27:00 AM
[/b][/size][/size][/size][/size]
Way to go! Obscure troubleshooting at it's best!
Typical troubleshooting: It's always the last thing you try
August 21, 2016, 01:52:16 AM
[/b][/size][/size][/size][/size]
Way to go! Obscure troubleshooting at it's best!
Typical troubleshooting: It's always the last thing you try
August 20, 2016, 10:20:07 PM
Man...the amount of angst $2 bad hardware can cause...the mini usb patch between the A6 AUC adapter and the RPi was bad on the signal side. I swapped it for the better quality cable I'd been using for the power input...and so...
I said...I say-ed...
Yowza! I got hash!
I said...I say-ed...
Yowza! I got hash!
Way to go! Obscure troubleshooting at it's best!
August 20, 2016, 09:17:40 PM
That is terrific Firetree!
The amount of expertise here on kano amazes me.
I'll be in line with everyone else to try out the new Avalons. Hopefully soon.
The amount of expertise here on kano amazes me.
I'll be in line with everyone else to try out the new Avalons. Hopefully soon.
Mahalo (thanks)! Lots of mana'o (loosely translated, expertise) here for sure, and several folks PM'd with some pretty helpful info. I had to wade through all the obvious, and even more obtuse, stuff to eliminate all but the real cause. I think that's always been my least favorite troubleshoot...when it turns out to be a 50-cent fuse on a circuit that isn't supposed to be used...that sort of thing.
Yup, once I get the second A6 online here at home, I think it'll be time (and enough BTC in the wallet) to pick up the next-gen Avalon box, which according to all the chatter is trying to launch in Sept. All I know is what I see on the board. We've got some good years of mining left given the level of hw production I know they can do.
Mine on...
August 20, 2016, 08:59:04 PM
That is terrific Firetree!
The amount of expertise here on kano amazes me.
I'll be in line with everyone else to try out the new Avalons. Hopefully soon.
The amount of expertise here on kano amazes me.
I'll be in line with everyone else to try out the new Avalons. Hopefully soon.
August 20, 2016, 06:53:56 PM
Man...the amount of angst $2 bad hardware can cause...the mini usb patch between the A6 AUC adapter and the RPi was bad on the signal side. I swapped it for the better quality cable I'd been using for the power input...and so...
I said...I say-ed...
Yowza! I got hash!
I said...I say-ed...
Yowza! I got hash!
August 20, 2016, 06:12:36 PM
Is your AUC controller red or green. if it's red then something not connecting
it should go from blue to green but sometimes flashes red then green.
On dashboard did it show the temp?
it should go from blue to green but sometimes flashes red then green.
On dashboard did it show the temp?
The LED on the A6 is flashing green. You can see from the pic that nothing is coming through. The pool assignments are OK, but that's it.
If the led on the A6 is flashing green it hasn't completed it's start up.
August 20, 2016, 05:49:22 PM
Is your AUC controller red or green. if it's red then something not connecting
it should go from blue to green but sometimes flashes red then green.
On dashboard did it show the temp?
it should go from blue to green but sometimes flashes red then green.
On dashboard did it show the temp?
The LED on the A6 is flashing green. You can see from the pic that nothing is coming through. The pool assignments are OK, but that's it.
August 20, 2016, 05:12:45 PM
Hi Actual, I had a similar problem when I got a RPi3 to update so I could use the wifi option and use on the new Avalon?. Wish I could find were to buy a AUC controller. BlockC always goes to DHCP, maybe it can be changed I'm not sure.
I downloaded the latest firmware from Avalon, it goes to static you need to do your setup on dashboard before you go to advanced, on network set the last dns setting to 114.114.114.114 it will not affect the dns on your computer, once it's running then go to advance. do your password and you will stay on advance, I don't think you can go back to dashboard. when you login again use 192.168.0.100
hope this helps
Chili
I downloaded the latest firmware from Avalon, it goes to static you need to do your setup on dashboard before you go to advanced, on network set the last dns setting to 114.114.114.114 it will not affect the dns on your computer, once it's running then go to advance. do your password and you will stay on advance, I don't think you can go back to dashboard. when you login again use 192.168.0.100
hope this helps
Chili
Thanks, Chili, but already been there. This is what the status looks like...whether the A6 is powered up or not. Dunno if it's a bad USB cable or what.
https://i.imgur.com/WNGDQqM.png
it should go from blue to green but sometimes flashes red then green.
On dashboard did it show the temp?
August 20, 2016, 04:51:14 PM
Hi Actual, I had a similar problem when I got a RPi3 to update so I could use the wifi option and use on the new Avalon?. Wish I could find were to buy a AUC controller. BlockC always goes to DHCP, maybe it can be changed I'm not sure.
I downloaded the latest firmware from Avalon, it goes to static you need to do your setup on dashboard before you go to advanced, on network set the last dns setting to 114.114.114.114 it will not affect the dns on your computer, once it's running then go to advance. do your password and you will stay on advance, I don't think you can go back to dashboard. when you login again use 192.168.0.100
hope this helps
Chili
I downloaded the latest firmware from Avalon, it goes to static you need to do your setup on dashboard before you go to advanced, on network set the last dns setting to 114.114.114.114 it will not affect the dns on your computer, once it's running then go to advance. do your password and you will stay on advance, I don't think you can go back to dashboard. when you login again use 192.168.0.100
hope this helps
Chili
Thanks, Chili, but already been there. This is what the status looks like...whether the A6 is powered up or not. Dunno if it's a bad USB cable or what.
August 20, 2016, 04:27:36 PM
Block by pr3hm with 5.07THs! This would be his 2nd Kano block and our 2nd of the day!
Wow! what are the odds? Been running 6 S2's for about 10 months (didn't find any blocks) but sold 5 of them the last couple of months and replaced them with a single S7. This S7 isn't even running for a full month and it found not 1 but 2 blocks! Must be a very lucky one
Proud to be on the acclaim list and let's hope it finds many more on this pool! August 20, 2016, 04:11:18 PM
Can someone point me to an appropriate thread so I can get this A6 running? I finally got the SD card(s) burned (both Avalon and BlockC), and the RPi boots, but when using the BlockC card (has DHCP) I went to "Advanced", and now can't get back to the dashboard. Don't wanna change my network to the 192.168.0.xx config, but may have to, I guess. The RPi shows on the router, but no connection to the pool.
Thanks again. Maybe shoulda hadda oughta stayed with BiteMe.
Hi Actual, I had a similar problem when I got a RPi3 to update so I could use the wifi option and use on the new Avalon?. Wish I could find were to buy a AUC controller. BlockC always goes to DHCP, maybe it can be changed I'm not sure.Thanks again. Maybe shoulda hadda oughta stayed with BiteMe.
I downloaded the latest firmware from Avalon, it goes to static you need to do your setup on dashboard before you go to advanced, on network set the last dns setting to 114.114.114.114 it will not affect the dns on your computer, once it's running then go to advance. do your password and you will stay on advance, I don't think you can go back to dashboard. when you login again use 192.168.0.100
hope this helps
Chili
August 20, 2016, 03:45:21 PM
Why are you guys not waiting for the Avalon to be released? Its soon september and I think Avalon is going to surprise us.... in a good way I hope
August 20, 2016, 02:54:50 PM
Looks like my keepkey discovered a bug. New beta firmware release available later today.
Guys over at keepkey are on the stick. Very pleased. They are the KANO of hardware wallets.
Yay! I'm 1btc richer that I thought.
Blockchain does not lie.
Blocks have been a bit stubborn. Let's roll!
Guys over at keepkey are on the stick. Very pleased. They are the KANO of hardware wallets.
Yay! I'm 1btc richer that I thought.
Blockchain does not lie.
Blocks have been a bit stubborn. Let's roll!
Similar experience, one of their senior developers, Ken, actually called me to explain what was going on and ask if I wanted to be part of the beta firmware and app update
They did not get it fixed Friday, looks like Monday now. Coins are safe, just cannot get to them until Monday.
August 20, 2016, 02:39:08 PM
Can someone point me to an appropriate thread so I can get this A6 running? I finally got the SD card(s) burned (both Avalon and BlockC), and the RPi boots, but when using the BlockC card (has DHCP) I went to "Advanced", and now can't get back to the dashboard. Don't wanna change my network to the 192.168.0.xx config, but may have to, I guess. The RPi shows on the router, but no connection to the pool.
Thanks again. Maybe shoulda hadda oughta stayed with BiteMe.
I had to use 8.8.8.8 as my DNS server. (google DNS)Thanks again. Maybe shoulda hadda oughta stayed with BiteMe.
Datacenter set up my firewall and I could not use 192.168.1.1 as the DNS (same as gateway)
August 20, 2016, 02:00:59 PM
Block by mhumaidan with 14.45THs! Welcome to the Acclaim Board with your 1st Kano block...and this is our 4th of the day!
August 20, 2016, 01:49:56 PM
Can someone point me to an appropriate thread so I can get this A6 running? I finally got the SD card(s) burned (both Avalon and BlockC), and the RPi boots, but when using the BlockC card (has DHCP) I went to "Advanced", and now can't get back to the dashboard. Don't wanna change my network to the 192.168.0.xx config, but may have to, I guess. The RPi shows on the router, but no connection to the pool.
Thanks again. Maybe shoulda hadda oughta stayed with BiteMe.
Thanks again. Maybe shoulda hadda oughta stayed with BiteMe.
August 20, 2016, 09:32:46 AM
Looks like my keepkey discovered a bug. New beta firmware release available later today.
Guys over at keepkey are on the stick. Very pleased. They are the KANO of hardware wallets.
Yay! I'm 1btc richer that I thought.
Blockchain does not lie.
Blocks have been a bit stubborn. Let's roll!
Guys over at keepkey are on the stick. Very pleased. They are the KANO of hardware wallets.
Yay! I'm 1btc richer that I thought.
Blockchain does not lie.
Blocks have been a bit stubborn. Let's roll!
Similar experience, one of their senior developers, Ken, actually called me to explain what was going on and ask if I wanted to be part of the beta firmware and app update
August 20, 2016, 09:22:08 AM
Block by randybtc100! That is his 12th Kano block and our 3rd of the day!
Jump to: