can you use usb 3 hub with this controller ?
Why not? Just make sure to daisy chain properly, have one root hub where the other hubs connected to.
Topic: LightningAsic Gridseed Controller Firmware V3 - page 16. (Read 51104 times)
Why not? Just make sure to daisy chain properly, have one root hub where the other hubs connected to.
can you use usb 3 hub with this controller ?
After flashing my wiibox to V3c i can acess control panel and insert pool details etc but i´m having problems detecting the miners, sometimes one or two appears but then they disconnect again, i´m using a 10 port hub with 10 miners connected
Power cycle your controller, that should fix it.
After flashing my wiibox to V3c i can acess control panel and insert pool details etc but i´m having problems detecting the miners, sometimes one or two appears but then they disconnect again, i´m using a 10 port hub with 10 miners connected
I have a few of these wiibox controllers that are now extra if anyone needs one pre-flashed to the V3c firmware. I paid $50 each and I would sell them for the same. Send me a pm if you need one.
Edit: I have four wiibox controllers running V3c left. One on reserve.
Edit: I have four wiibox controllers running V3c left. One on reserve.
I have successfully flashed a wiibox using the directions in the OP and the following software (Win7)
Download WinSCPPortableApp http://portableapps.com/apps/internet/winscp_portable
Log in to your wiibox as "SCP" and enter "root" for the username.
The password is either
2.02 or lower "123456"
2.0.3 or higher "+xTjPR4L%V?=s4-!Ahz3~FXZM^sW:gA_"
Then copy over the V1 upgrade image to the root directory and launch a terminal window within WinSCP (or use putty.exe to SSH in). Type "mtd -r write LAG3355_upgrade_v1.bin firmware" and click execute.
It will freeze and need a hard reset. Then you will be assigned a new ip address by your router.
Type in the new address in a Chrome 'incognito' session and upgrade to the V3c firmware. Walla!
Download WinSCPPortableApp http://portableapps.com/apps/internet/winscp_portable
Log in to your wiibox as "SCP" and enter "root" for the username.
The password is either
2.02 or lower "123456"
2.0.3 or higher "+xTjPR4L%V?=s4-!Ahz3~FXZM^sW:gA_"
Then copy over the V1 upgrade image to the root directory and launch a terminal window within WinSCP (or use putty.exe to SSH in). Type "mtd -r write LAG3355_upgrade_v1.bin firmware" and click execute.
It will freeze and need a hard reset. Then you will be assigned a new ip address by your router.
Type in the new address in a Chrome 'incognito' session and upgrade to the V3c firmware. Walla!
Can we use this on original Gridseed controllers?? I mean WIIBOX ??
Flashing will work on Wiibox controller, they essentially have the same chipset.
I will have to give this a try. Can you post a Litecoin donation address?
Lc75scqhMCkpMhC3aYGPVB4BEAzHvvz2rm
Small donation sent. Let's see some more from others here
. http://explorer.litecoin.net/tx/284de26cf9ac6321f85da2142b9eeeb1c07a78e5dbadc10e16aef2413528dbe0#o0Thanks a lot, you're awesome.
If you could add this version for WIIBOX and for TP-LINK MR3020 i can give you also some Btc bounty
Can we use this on original Gridseed controllers?? I mean WIIBOX ??
Flashing will work on Wiibox controller, they essentially have the same chipset.
I will have to give this a try. Can you post a Litecoin donation address?
Lc75scqhMCkpMhC3aYGPVB4BEAzHvvz2rm
Small donation sent. Let's see some more from others here
. http://explorer.litecoin.net/tx/284de26cf9ac6321f85da2142b9eeeb1c07a78e5dbadc10e16aef2413528dbe0#o0Thanks a lot, you're awesome.
LIGHTNINGASIC GRIDSEED SCRYPT ONLY MINER BLADE
There are 2 PCBA.
Each PCBA 40 GC3355 chips.
Each PCBA has it’s own power socket and usb port.
one 80-chip blade miner is equivalent to 16 5-chip USB miners
Official Scrypt hashrate is 5.2M (2.6M on each PCBA)
Scrypt only mode: 64-70W on each PCBA. (140W per miner)
PSU/Controller/USB cables are included.
There are 2 PCBA.
Each PCBA 40 GC3355 chips.
Each PCBA has it’s own power socket and usb port.
one 80-chip blade miner is equivalent to 16 5-chip USB miners
Official Scrypt hashrate is 5.2M (2.6M on each PCBA)
Scrypt only mode: 64-70W on each PCBA. (140W per miner)
PSU/Controller/USB cables are included.
Latest firmware performs really well - good uptime less dead miners for me
Can we use this on original Gridseed controllers?? I mean WIIBOX ??
Flashing will work on Wiibox controller, they essentially have the same chipset.
I will have to give this a try. Can you post a Litecoin donation address?
Lc75scqhMCkpMhC3aYGPVB4BEAzHvvz2rm
Small donation sent. Let's see some more from others here
. http://explorer.litecoin.net/tx/284de26cf9ac6321f85da2142b9eeeb1c07a78e5dbadc10e16aef2413528dbe0#o0 Can we use this on original Gridseed controllers?? I mean WIIBOX ??
Flashing will work on Wiibox controller, they essentially have the same chipset.
I will have to give this a try. Can you post a Litecoin donation address?
Lc75scqhMCkpMhC3aYGPVB4BEAzHvvz2rm
Can we use this on original Gridseed controllers?? I mean WIIBOX ??
Flashing will work on Wiibox controller, they essentially have the same chipset.
I will have to give this a try. Can you post a Litecoin donation address?
Can we use this on original Gridseed controllers?? I mean WIIBOX ??
Flashing will work on Wiibox controller, they essentially have the same chipset.
Quote
(miners: 10/10 uptime: 108:57:04, memory usage: 32%, load average: )
Running just fine since i upgraded
Can we use this on original Gridseed controllers?? I mean WIIBOX ??
I am pretty sure it is a different hardware setup and it will not work with this firmware. I still like the original wiibox controllers (up to 2.1.2). You just need to overclock them to 850. They can still dual mine BTC at roughly 100gh SHA and 3000-3100kh scrypt per 10 miners.
Can we use this on original Gridseed controllers?? I mean WIIBOX ??
I keep getting "failed to unpack" messages on every single bin I try to upload to the controllers...both of them. I'm REALLY aggravated at this point, because the version of the firmware I'm using, I can't even get my miners to submit shares on half the pools I use, seems like. Serves me right for not waiting to see if it was stable before flashing it.
If you have the first version of a V3, try a LTC pool. I have one on V3c and one on V3. The V3c is running better but both work fine at 850. Don't try to adjust individual miners with the first version of V3, it starts spewing stale shares and rejects. Do a hard reset and it should work fine on a straight LTC pool at 512 dif.
I keep getting "failed to unpack" messages on every single bin I try to upload to the controllers...both of them. I'm REALLY aggravated at this point, because the version of the firmware I'm using, I can't even get my miners to submit shares on half the pools I use, seems like. Serves me right for not waiting to see if it was stable before flashing it.
Try the v1 bin image.
Thnx, working now!ps: Did you consider implementing some kind of autotuning feature? Would be nice if the software would be able to automatically adjust the frequency per miner to get the highest shares / lowest hw errors.
By the way, new features coming up: auto frequency tuning, revamped mining algorithm (+30kh/s/miner), detecting the IPs of running LightningAsic controllers...
After 12 hours of mining @ Ghash.io, and that's on crappy internet...
I have one LA controller upgraded to V3 and another LA controller upgraded to V3c both work a lot better than the original versions 1 and 2. Great job on the new firmware. Looking forward to your next upgrade with auto frequency tuning.Thanks for efforts.
Jump to: