Pages:
Author

Topic: [GROUP BUY WORLDWIDE]BTMine v1 Miner 200GH/s BTC 2.4 - page 30. (Read 97316 times)

sr. member
Activity: 504
Merit: 250

so I am stuck with a bad setup for my wifi connection. I can access the interface without problem, but I can't apply change to cgminer.

I've got

Applying changes
Loading /etc/config/cgminer

with the wheel rolling forever...

Is that a port problem ? can anyone help ? Someone was talking about a teamviewer help, that'd be super cool Smiley

That will keep rolling forever if you setup pool server for CGminer and dont have working internet connection settings.
working Gateway
working DNS

cgminer will try to connect  the pool but fails and wont startup.

you have to powercycle the unit, check you internet connection settings then try cgminer setup again. if yo u get that wheel rolling forever again your internet connection settings fail.
---> Fix internet first.
hero member
Activity: 784
Merit: 500
someone knows how to mine by pluggin the usb to my laptop  ? Version of cgminer / .bat to use ?

i pm'd btmine, if they can ship the defective part and I can mine connected to a computer I'll be happy.

Are you sure it's not your PSU? I had the same screen issue when I tried to run it from a blown PSU. The intro screen popped up and then went dead. Does the loud fan come on?

If the FPGA module is not working, use a laptop and control it with cgminer via USB. cgminer 3.9.0 should work fine.

yes the fan are ultra loud 80 or 100% i'd say.

ok i'll check this tomorrow and i'll ask another module.

thanks.

first, thanks everybody for help.

I found the reset button and it worked. I can now access the interface ! 18 hours later finally.

So I setup the wifi, that's currently working fine on a new ip.

Now my problem is :

[Firmware Version] => 20130821
cgminer-70bc62c
luci-d854edc+
cgminer-openwrt-packages-800cc58
Socket connect failed: Connection refused


any ideas ?

so I am stuck with a bad setup for my wifi connection. I can access the interface without problem, but I can't apply change to cgminer.

I've got

Applying changes
Loading /etc/config/cgminer

with the wheel rolling forever...

Is that a port problem ? can anyone help ? Someone was talking about a teamviewer help, that'd be super cool Smiley
newbie
Activity: 29
Merit: 0
I have the same problem with three PSU... 630W thermaltake and 650W seasonic... Both of them are declared to have higher current on 12V then their "original" PSU. Second on, Seasonic 850W works without problems, it runs also fans, that's why I put stronger one
full member
Activity: 205
Merit: 100
Unplug the power for the blades and see if it's a power issue. You can access the webUI without the blades plugged in.
sr. member
Activity: 546
Merit: 255
10-12 days seems about on par with what's been happening lately.

Can anyone confirm or deny if I should just trash the included PSU's in the US?

They are 170-230Vac you need 220v connection for them. See pictures few pages back.

They will work fine as long as they don't blow up.

Now New problem I purchased 2 coolmax PSU and they are rated for 750w @57a and for some reason they are not powering up when connected to the power distribution board. Does both PSU have to match for it to work? are the 2 6 pins are inter changeable? Not sure what's going wrong but it does not power up. I can do the paperclip trick and it runs but it will not power the blade. I'm halfway there just need to get power to the other blade. Anyone know this answer?
newbie
Activity: 45
Merit: 0
I received DHL number from 1/8/2014 order today... just 12 days later.

If not a secret, where are you from and you paid with Paypal or BTC?

Just received ems tracking number. But how track it?

Paid with BTC and from Europe.

DHL tracking number can be set on the dhl webpage.

Středa, Leden 22, 2014    Místo    Čas    Kusy
1    Přijata data o zásilce    HONG KONG - HONG KONG    00:56
sr. member
Activity: 504
Merit: 250
10-12 days seems about on par with what's been happening lately.

Can anyone confirm or deny if I should just trash the included PSU's in the US?

They are 170-230Vac you need 220v connection for them. See pictures few pages back.
newbie
Activity: 58
Merit: 0
I received DHL number from 1/8/2014 order today... just 12 days later.

If not a secret, where are you from and you paid with Paypal or BTC?

Just received ems tracking number. But how track it?
newbie
Activity: 45
Merit: 0
I received DHL number from 1/8/2014 order today... just 12 days later.
full member
Activity: 188
Merit: 100
Need some help guys removing Fuse1 on my dead Avalon modules.  I've confirmed that several of my Fuse1's are blown using a multimeter but I can't figure out how to remove them from the board.  I tried to heat them up to melt the solder joints by using a solding iron, but they didn't budge.  I also tried putting extra solder on the joints to improve heat transfer but instead made a big mess on the board.  

Do I need to get a heat gun to remove these fuses or is there any other way to get them off with a solding iron?


Thanks... and sorry for the technical incompetency here.
newbie
Activity: 16
Merit: 0
sr. member
Activity: 546
Merit: 255
Here's a screenshot:



Running 2 Cooler Master 625w PSU. Might need to change the fan, running like a vacumm sound.

How many amps?
newbie
Activity: 16
Merit: 0
Here's a screenshot:

http://s13.postimg.org/dg73xn1tv/avalon200gh.jpg

Running 2 Cooler Master 625w PSU. Might need to change the fan, running like a vacumm sound.
sr. member
Activity: 546
Merit: 255
Okay that worked. How did you set it up so that it worked?

I changed the pool and got this

[Firmware Version] => 20131110
cgminer: 176747f
cgminer-openwrt-packages: 0e12b1b
luci: 346e3e7
Socket connect failed: Connection refused


Give it time to connect, it usually says this for the first 30-60sec. If it never connects, try opening the ports on your router of the pools you're connecting to (3333 or 3334 for example). Also make sure your credentials (worker/pass) are right

You were right. Its going now next to get a power supply that works. What are the recommendations?
full member
Activity: 231
Merit: 100
Okay that worked. How did you set it up so that it worked?

I changed the pool and got this

[Firmware Version] => 20131110
cgminer: 176747f
cgminer-openwrt-packages: 0e12b1b
luci: 346e3e7
Socket connect failed: Connection refused


Give it time to connect, it usually says this for the first 30-60sec. If it never connects, try opening the ports on your router of the pools you're connecting to (3333 or 3334 for example). Also make sure your credentials (worker/pass) are right
sr. member
Activity: 546
Merit: 255
Okay that worked. How did you set it up so that it worked?

I changed the pool and got this

[Firmware Version] => 20131110
cgminer: 176747f
cgminer-openwrt-packages: 0e12b1b
luci: 346e3e7
Socket connect failed: Connection refused
sr. member
Activity: 546
Merit: 255
Okay that worked. How did you set it up so that it worked?
hero member
Activity: 994
Merit: 500
Np, I reset the tplink plugged it into my router. Then logged into my router and viewed devices and found the ip that way.
sr. member
Activity: 546
Merit: 255
Did you try 192.168.0.100? That's the default
I reset mine with the little button on the front and it just reset to that ip.

I will try that next Thank you.
hero member
Activity: 994
Merit: 500
Did you try 192.168.0.100? That's the default
I reset mine with the little button on the front and it just reset to that ip.
Pages:
Jump to: