Topic: [Minera v0.9.0] Your next mining dashboard - S9/L3+/D3/CPUminer/CGminer/BFGminer - page 37. (Read 850502 times)

they use the same (stratum), so if you have shares accepted, you can remove the solo pool as it was just there to verify your config

and it works:
http://solo.ckpool.org/users/1KMVTDhcwP6Yic9MgYjQLjaKfvaAFSyu7W

I maybe confusing things but pool 0 is the solo de.ckpool.org and pool 1 is my old seting on the shared pool stratum.bitcoin.cz. I have now started a new run from power up on the solo pool and in 42 minutes I have 150 shares accepted so I may leave things like that for a while and try the shared pool again later.

I would like to know if changing the pool got things running, do ckpool and bitcoin.cz use a different protocol to communicate with the miner or something?

Andy

I don't know, you;re mining on pool 1 (no specified)

solo is pool 0
 [2016-11-12 10:47:38.808] Pool 0 message: Authorised, welcome to de.ckpool.org 1KMVTDhcwP6Yic9MgYjQLjaKfvaAFSyu7W!

Is the log good, nothing to worry about. If I am running about 20+Ghs about how long to submit a share?

Andy

go to:
http://solo.ckpool.org/users/1KMVTDhcwP6Yic9MgYjQLjaKfvaAFSyu7W

looks like you've not submitted any share yet.

still connecting to  [2016-11-12 09:41:57.748] Failed to resolve (?wrong URL) ltc.ghash.io:3333

That was the donation pool, I have deleted it. I am sure I can put it back if needed. It is just a Pi B running a Minera 0.7.0 image off a MicroSD card, I have done nothing to the install so I hope there is enough free space. I have just tried a solo pool to see if I can get that working.

Andy

I set my pool to 'stratum+tcp://de.ckpool.org:3333' and the user to my Wallet address with a password of 'x'

After 10 minutes the log is:

 [2016-11-12 09:41:50.534] Started cgminer 4.9.2
 [2016-11-12 09:41:50.535] Loaded configuration file /var/www/minera/conf/miner_conf.json
 [2016-11-12 09:41:57.682] Probing for an alive pool
 [2016-11-12 09:41:57.748] Failed to resolve (?wrong URL) ltc.ghash.io:3333
 [2016-11-12 09:41:57.772] Pool 0 difficulty changed to 1000
 [2016-11-12 09:41:57.816] Pool 0 message: Authorised, welcome to de.ckpool.org 1KMVTDhcwP6Yic9MgYjQLjaKfvaAFSyu7W!
 [2016-11-12 09:41:57.942] Pool 1 difficulty changed to 256
 [2016-11-12 09:41:58.684] Network diff set to 255G
 [2016-11-12 09:42:03.685] API running in IP access mode on port 4028 (12)
 [2016-11-12 09:45:50.281] Stratum connection to pool 0 interrupted
 [2016-11-12 09:45:50.363] Pool 0 difficulty changed to 1000
 [2016-11-12 09:45:50.405] Pool 0 message: Authorised, welcome to de.ckpool.org 1KMVTDhcwP6Yic9MgYjQLjaKfvaAFSyu7W!
 [2016-11-12 09:45:50.408] Stratum from pool 0 requested work restart
 [2016-11-12 09:46:53.687] Lost 2 shares due to no stratum share response from pool 0
 [2016-11-12 09:47:32.102] AU3 0: No valid hashes for over 2 secs, attempting to reset
 [2016-11-12 09:47:32.300] AU3 0 attempted reset got err:(0) LIBUSB_SUCCESS
 [2016-11-12 09:47:53.180] Stratum connection to pool 0 interrupted
 [2016-11-12 09:47:53.312] Pool 0 difficulty changed to 1000
 [2016-11-12 09:47:53.355] Pool 0 message: Authorised, welcome to de.ckpool.org 1KMVTDhcwP6Yic9MgYjQLjaKfvaAFSyu7W!
 [2016-11-12 09:47:53.360] Stratum from pool 0 requested work restart
 [2016-11-12 09:48:28.689] Lost 1 shares due to no stratum share response from pool 0
 [2016-11-12 09:49:34.129] Stratum from pool 0 detected new block at height 438528
 [2016-11-12 09:50:51.365] Stratum from pool 0 detected new block at height 438529
 [2016-11-12 09:53:26.153] Stratum connection to pool 0 interrupted
 [2016-11-12 09:53:26.286] Pool 0 difficulty changed to 1000
 [2016-11-12 09:53:26.329] Pool 0 message: Authorised, welcome to de.ckpool.org 1KMVTDhcwP6Yic9MgYjQLjaKfvaAFSyu7W!
 [2016-11-12 09:53:26.333] Stratum from pool 0 requested work restart

Andy

You have the wrong pool sets: [2016-11-12 08:56:27.198] Failed to resolve (?wrong URL) ltc.ghash.io:3333
Try to save the settings again and restart, if it persists you have some issue on saving data, check you have disk space.

[2016-11-12 08:56:27.198] Failed to resolve (?wrong URL) ltc.ghash.io:3333 <<== isn't that a clear enough message ?



plus ltc is not BTC, it is scrypt, so the gekko won't be useful.

it's obviously not using stratum+tcp://stratum.bitcoin.cz:3333

Thanks nice tool very usefull

I am using 'stratum+tcp://stratum.bitcoin.cz:3333' with a user of 'andythw.pi' which works on my U3 and R1 under different worker names.

The log below looks OK to me apart from the lost shares at the end:

[2016-11-12 08:56:20.024] Started cgminer 4.9.2
[2016-11-12 08:56:20.024] Loaded configuration file /var/www/minera/conf/miner_conf.json
[2016-11-12 08:56:26.861] Probing for an aliveool
[2016-11-12 08:56:27.137] Pool 1 difficulty changed to 256
[2016-11-12 08:56:27.148] Pool 0 difficulty changed to 256
[2016-11-12 08:56:27.198] Failed to resolve (?wrong URL) ltc.ghash.io:3333
[2016-11-12 08:56:27.862] Network diff set to 255G
[2016-11-12 08:56:32.863] API running in IP access mode on port 4028 (14)
[2016-11-12 08:56:38.067] AU3 1: No valid hashes for over 2 secs, attempting to reset
[2016-11-12 08:56:38.270] AU3 1 attempted reset got err:(0) LIBUSB_SUCCESS
[2016-11-12 08:56:54.715] Pool 0 difficulty changed to 51
[2016-11-12 08:56:54.716] Stratum from pool 0 requested work restart
[2016-11-12 08:58:24.798] Stratum connection to pool 0 interrupted
[2016-11-12 08:58:25.055] Pool 0 successfully negotiated resume with the same session ID
[2016-11-12 08:58:25.055] Pool 0 difficulty changed to 256
[2016-11-12 08:58:25.058] Stratum from pool 0 detected new block at height 438524
[2016-11-12 08:58:57.864] Lost 1 shares due to no stratum share response from pool 0
[2016-11-12 08:59:07.864] Lost 1 shares due to no stratum share response from pool 0
[2016-11-12 08:59:15.279] Pool 0 difficulty changed to 51
[2016-11-12 08:59:15.280] Stratum from pool 0 requested work restart
[2016-11-12 08:59:32.864] Lost 1 shares due to no stratum share response from pool 0
[2016-11-12 08:59:45.609] Pool 0 difficulty changed to 10
[2016-11-12 08:59:45.610] Stratum from pool 0 requested work restart
[2016-11-12 08:59:47.864] Lost 1 shares due to no stratum share response from pool 0
[2016-11-12 08:59:52.864] Lost 1 shares due to no stratum share response from pool 0
[2016-11-12 08:59:57.865] Lost 2 shares due to no stratum share response from pool 0
[2016-11-12 09:00:02.865] Lost 1 shares due to no stratum share response from pool 0
[2016-11-12 09:00:07.865] Lost 2 shares due to no stratum share response from pool 0

If this is nt a Minera issue I would like confrmation my miner settings are correct, I am using CGminer 4.x (Official) with no startup options and a delayed start of 20 seconds.

Andy

not
a
minera
issue


Minera is a monitor, it doesn't do anything apart from reporting.

cgminer/bfgminer does the work.

gekkosticks are for BTC only.

try the solo pool for a while and give us your results...

like this:
http://solo.ckpool.org/workers/1GjdERDYEDQmyoZHnVnshBbVNBckDw4dnj.gekko1:

What pool are you using? It seems you are using a pool with different algo supported. Please check also the logs in the bottom of the dashboard.

Just in case I was being too hasty I ran my 2 gekko sticks over night for 12 hours I have Current Shares of 1106165 but none accepted or rejected. I have looked at the pool and user name again and they look correct. The dashboard for the pool shows no work being dome under that worker name, any thoughts on what I am doing wrong?

Andy

I have a question. For Gridseed Blade 40 chips will go to this controller? And with Raspberry Pi 3 Model B will work?

so i just got in a Zeus Thunder x6 NX and i have it on and setup and its running well, but i also have a gridseed 5 chip plugged in as well.
The zeus miner is running and i saved the config for the Zeus but how can i run the CGMiner for Zeus AND cpuminer for the gridseed?

Basically i would be running dual miner programs(cgminer and cpuminer or cgminer for zeus and cgminer for gridseed) with two different devices on the same raspberry pi.
I was thinking about adding a new line under the rc.local script but everytime i tried to add the cpuminer under the cgminer config it just cleared it out after i saved.
Any help is appreciated thanks!

And yes i'm new to the whole miner thing so this may seem simple to you but i couldn't find anything useful about my issue.

minera doesn't support HW.

minera moinitors your mining SW, so it the A4 Dominator uses supported SW, then it'll work.

The A4 Dominator from Innosilicon has started to ship.  Would you be interested in adding the A4 to the supported miners for Minera?