Pages:
Author

Topic: My RX580 Benchmarking and Results: 30.5Mh/s @ 77.5W (+ 1130MH/s Dcr w/ 125W) - page 13. (Read 189836 times)

legendary
Activity: 1098
Merit: 1000
Apneal / Truthchanter

Thanks to you both for all the useful information, only recently got back into GPU mining and I seem to have forgotten everything I used to know and lots of things are new Smiley

Fired up my old 7950's that had been gathering dust and I got some new MSI RX580 Gaming X 8Gb cards and they come with Samsung Memory.

All I have done so far is copy the 1:1750 strap to the 1:2000 strap, currently using -cclock 1135 -cvddc 975 -mclock 2150 and getting much better results than stock of around 30MH and 100w per card ETH mining only, the problem I am having is when I try to dual mine with decred. My numbers go to pot, the ETH mining speed drops significantly to around 28MH even when the DCR speeds are much lower than yours around 600.

Could either of you share your claymore command lines to see if I am doing anything obviously wrong.

Also that doreymills site that was linked earlier, my original 1:1750 strap is
Code:
777000000000000022CC1C00106A6D4DD0571016B90D060C006AE70014051420FA8900A0030000001B11333DC0303A17
and it gives me
Code:
777000000000000022CC1C00106A5D4DD0571016B90D060C0060070014051420FA8900A0030000001011333DC0303A17

Do I copy the new one to both the 1:1750 and 1:2000 or just one of them, or do I do the 1:1750 then use the tool on the 1:2000 and get a new value for that too ?

TIA
sr. member
Activity: 266
Merit: 250
What dcri value do you use to get these hashrates?
newbie
Activity: 1
Merit: 0

Can you post the custom timings string? These of course are the same chips as before some optimum strings have already been found, but I like this one due to only needing 2100 MHz Smiley Very nice target to get 30.5 MHs


Its Samsung memory using Uber Mix straps from the Polaris Bios Editing main thread (google).

Might have missed it in this thread but just to confirm: UberMix v3.1 strap mod copied over all straps above 1500 for your Sapphire ?

Cheers
sr. member
Activity: 266
Merit: 250


Your card is ~250w from the wall, you need to undervolt it!

Well the idea was to tune the hashrate first, the power consumption after.. Unless undervolting is part of the tuning to get the max hashrate?
full member
Activity: 173
Merit: 100
Ì am about to pull my hair out. I have RX 580 with samsung memory but what I do it seems like my hashrate only goes down. At stock they do 24MH/s ETH / 480MH/s PASC.

This is my card in stock;




I copied the straps from 1750 to 2000. So far so good and the hashrate remains pretty much unchanged. When I change the core clock to whatever value my hashrate only goes down. What the heck do I do wrong? I follow https://www.youtube.com/watch?v=FT9K8DqaeDs to the letter but only bad results.. Can anyone help me?

Your card is ~250w from the wall, you need to undervolt it!
sr. member
Activity: 266
Merit: 250
Ì am about to pull my hair out. I have RX 580 with samsung memory but what I do it seems like my hashrate only goes down. At stock they do 24MH/s ETH / 480MH/s PASC.

This is my card in stock;




I copied the straps from 1750 to 2000. So far so good and the hashrate remains pretty much unchanged. When I change the core clock to whatever value my hashrate only goes down. What the heck do I do wrong? I follow https://www.youtube.com/watch?v=FT9K8DqaeDs to the letter but only bad results.. Can anyone help me?
full member
Activity: 224
Merit: 102
I knew exactly how to use this tool immediately after he posted a link, because just by looking at the main page it basically says how to use it. You may want to go read the Polaris Bios Editor thread and get an idea of what straps are and memory timings and what this is trying to do.

I have modded lots of bioses, I know about straps and yes, I have read all 270+ pages about Polaris bios editor. There is just a blank page on the main page of the link, no info, no doc, so how can I know what it is exactly doing?  Maybe you have some other link...
I think for example "555000000000000022CC1C00AD515A3EC0570E142D4A640800400700030114207A8900A00300000%10span%20style=" with the span style at the end is definatelly not a valid strap...

Its a valid strap followed by some character codes for HTML. If you KNOW thats not part of the strap, why are you leaving it in? Remove the fluff, people shouldnt have to walk you through simple stuff at this level, and if they do then you should act like you need help and not act like tools which people took time out of their lives to make (which are valuable) aren't good enough for you.

All I wanted was just to know how this works, because there is no documentation. I was interested in it. And what I got? Only hatefull answers. Ok...
Yes, you're right. Sorry, I'm not so big King Kong as you are and I do not deserve any help. I not belong to your elite club. Enjoy your highness...

Go around and call other people's hard work "useless", and then the community who supports developers like this will keep it useless for you. Go sit in a corner and think about it.

I never called other people's hard work "useless"! Keep calm macho...
sr. member
Activity: 266
Merit: 250
I got my powercolor Red Devils (https://www.mindfactory.de/product_info.php/8GB-PowerColor-Radeon-RX-580-Red-Devil-Aktiv-PCIe-3-0-x16--Retail-_1167702.html ) in the mail yesterday and installed everything. They are now happily dual mining at ETC 24mh /s PASC 479 MH/s. I am not into modding bios'es yet. Would anyone be interested in tuning my cards. I'd happily take offers in PM  Smiley 
full member
Activity: 219
Merit: 100
I knew exactly how to use this tool immediately after he posted a link, because just by looking at the main page it basically says how to use it. You may want to go read the Polaris Bios Editor thread and get an idea of what straps are and memory timings and what this is trying to do.

I have modded lots of bioses, I know about straps and yes, I have read all 270+ pages about Polaris bios editor. There is just a blank page on the main page of the link, no info, no doc, so how can I know what it is exactly doing?  Maybe you have some other link...
I think for example "555000000000000022CC1C00AD515A3EC0570E142D4A640800400700030114207A8900A00300000%10span%20style=" with the span style at the end is definatelly not a valid strap...

Its a valid strap followed by some character codes for HTML. If you KNOW thats not part of the strap, why are you leaving it in? Remove the fluff, people shouldnt have to walk you through simple stuff at this level, and if they do then you should act like you need help and not act like tools which people took time out of their lives to make (which are valuable) aren't good enough for you.

All I wanted was just to know how this works, because there is no documentation. I was interested in it. And what I got? Only hatefull answers. Ok...
Yes, you're right. Sorry, I'm not so big King Kong as you are and I do not deserve any help. I not belong to your elite club. Enjoy your highness...

Go around and call other people's hard work "useless", and then the community who supports developers like this will keep it useless for you. Go sit in a corner and think about it.
full member
Activity: 224
Merit: 102
I knew exactly how to use this tool immediately after he posted a link, because just by looking at the main page it basically says how to use it. You may want to go read the Polaris Bios Editor thread and get an idea of what straps are and memory timings and what this is trying to do.

I have modded lots of bioses, I know about straps and yes, I have read all 270+ pages about Polaris bios editor. There is just a blank page on the main page of the link, no info, no doc, so how can I know what it is exactly doing?  Maybe you have some other link...
I think for example "555000000000000022CC1C00AD515A3EC0570E142D4A640800400700030114207A8900A00300000%10span%20style=" with the span style at the end is definatelly not a valid strap...

Its a valid strap followed by some character codes for HTML. If you KNOW thats not part of the strap, why are you leaving it in? Remove the fluff, people shouldnt have to walk you through simple stuff at this level, and if they do then you should act like you need help and not act like tools which people took time out of their lives to make (which are valuable) aren't good enough for you.

All I wanted was just to know how this works, because there is no documentation. I was interested in it. And what I got? Only hatefull answers. Ok...
Yes, you're right. Sorry, I'm not so big King Kong as you are and I do not deserve any help. I not belong to your elite club. Enjoy your highness...
full member
Activity: 219
Merit: 100
Anyone have an idea why the micron card refuses this strap mod? Currently I am running a mix of 1625 and 1750 for last 8 pairs.

The strap mod worked pretty good for Samsung. I think I prefer it over the ubermix.

Not sure, Micron might just be unstable at those timings. See what it changes, and then try something in between?
member
Activity: 98
Merit: 10
Anyone have an idea why the micron card refuses this strap mod? Currently I am running a mix of 1625 and 1750 for last 8 pairs.

The strap mod worked pretty good for Samsung. I think I prefer it over the ubermix.
full member
Activity: 219
Merit: 100
I knew exactly how to use this tool immediately after he posted a link, because just by looking at the main page it basically says how to use it. You may want to go read the Polaris Bios Editor thread and get an idea of what straps are and memory timings and what this is trying to do.

I have modded lots of bioses, I know about straps and yes, I have read all 270+ pages about Polaris bios editor. There is just a blank page on the main page of the link, no info, no doc, so how can I know what it is exactly doing?  Maybe you have some other link...
I think for example "555000000000000022CC1C00AD515A3EC0570E142D4A640800400700030114207A8900A00300000%10span%20style=" with the span style at the end is definatelly not a valid strap...

Its a valid strap followed by some character codes for HTML. If you KNOW thats not part of the strap, why are you leaving it in? Remove the fluff, people shouldnt have to walk you through simple stuff at this level, and if they do then you should act like you need help and not act like tools which people took time out of their lives to make (which are valuable) aren't good enough for you.
sr. member
Activity: 689
Merit: 253
What are  the dual mine speeds? (stock and modded). All topics only mention ETH mining..

I've been continuing to tweak and also optimizing for dual mining.

So far:

Eth: 30.5 Mh/s
Dcr: 1130 MH/s
VDDC: 0.877
Core: 1300
Mem: 2100
Mem voltage: 0.9
Strap: Custom mix
Mem Errors: 0/min
Power: 125W

NOTE: If you don't undervolt/limit power, it easily dual mines 30.5 MH/s + 1450 MH/s Dcr


Can you post the custom timings string? These of course are the same chips as before some optimum strings have already been found, but I like this one due to only needing 2100 MHz Smiley Very nice target to get 30.5 MHs


Can use 0150E2A3186272E16">http://doreymills.ca/cgi-bin/strapmod?555000000000000022CC1C00AD515A3EC0570E142D4A64080049C700030114207A8900A00300000 0150E2A3186272E16

just plug in your own 1500, 1625, or 1750

On that doreymills page there is no readme info guide how to exactly use it Sad
Useless

It may not be designed for newbs. I didn't design it but I find it easy and very useful. Like I said earlier you plug (copy) the strap you wanna mod into the tool (overwrite the default strap in the URL) and use the modded strap (the bottom of the 2 on the output page)

I am no newbie. I do always thinks after study documentation, to know exactly what am I doing and why. You did not write and no one told exactly what that tool/site really does under the hood. "Copy straps", which exactly, what is the reason? What does this tool change?
I am sad that there is so much people who just simply don't really want to help. They just wanna show how big kings they are and inside they glad their rigs are running better then others.

If you want help you are welcome to PM me
full member
Activity: 224
Merit: 102
I knew exactly how to use this tool immediately after he posted a link, because just by looking at the main page it basically says how to use it. You may want to go read the Polaris Bios Editor thread and get an idea of what straps are and memory timings and what this is trying to do.

I have modded lots of bioses, I know about straps and yes, I have read all 270+ pages about Polaris bios editor. There is just a blank page on the main page of the link, no info, no doc, so how can I know what it is exactly doing?  Maybe you have some other link...
I think for example "555000000000000022CC1C00AD515A3EC0570E142D4A640800400700030114207A8900A00300000%10span%20style=" with the span style at the end is definatelly not a valid strap...
full member
Activity: 219
Merit: 100
I knew exactly how to use this tool immediately after he posted a link, because just by looking at the main page it basically says how to use it. You may want to go read the Polaris Bios Editor thread and get an idea of what straps are and memory timings and what this is trying to do.
full member
Activity: 224
Merit: 102
What are  the dual mine speeds? (stock and modded). All topics only mention ETH mining..

I've been continuing to tweak and also optimizing for dual mining.

So far:

Eth: 30.5 Mh/s
Dcr: 1130 MH/s
VDDC: 0.877
Core: 1300
Mem: 2100
Mem voltage: 0.9
Strap: Custom mix
Mem Errors: 0/min
Power: 125W

NOTE: If you don't undervolt/limit power, it easily dual mines 30.5 MH/s + 1450 MH/s Dcr


Can you post the custom timings string? These of course are the same chips as before some optimum strings have already been found, but I like this one due to only needing 2100 MHz Smiley Very nice target to get 30.5 MHs


Can use 0150E2A3186272E16">http://doreymills.ca/cgi-bin/strapmod?555000000000000022CC1C00AD515A3EC0570E142D4A64080049C700030114207A8900A00300000 0150E2A3186272E16

just plug in your own 1500, 1625, or 1750

On that doreymills page there is no readme info guide how to exactly use it Sad
Useless

It may not be designed for newbs. I didn't design it but I find it easy and very useful. Like I said earlier you plug (copy) the strap you wanna mod into the tool (overwrite the default strap in the URL) and use the modded strap (the bottom of the 2 on the output page)

I am no newbie. I do always thinks after study documentation, to know exactly what am I doing and why. You did not write and no one told exactly what that tool/site really does under the hood. "Copy straps", which exactly, what is the reason? What does this tool change?
I am sad that there is so much people who just simply don't really want to help. They just wanna show how big kings they are and inside they glad their rigs are running better then others.
sr. member
Activity: 689
Merit: 253
What are  the dual mine speeds? (stock and modded). All topics only mention ETH mining..

I've been continuing to tweak and also optimizing for dual mining.

So far:

Eth: 30.5 Mh/s
Dcr: 1130 MH/s
VDDC: 0.877
Core: 1300
Mem: 2100
Mem voltage: 0.9
Strap: Custom mix
Mem Errors: 0/min
Power: 125W

NOTE: If you don't undervolt/limit power, it easily dual mines 30.5 MH/s + 1450 MH/s Dcr


Can you post the custom timings string? These of course are the same chips as before some optimum strings have already been found, but I like this one due to only needing 2100 MHz Smiley Very nice target to get 30.5 MHs


Can use 0150E2A3186272E16">http://doreymills.ca/cgi-bin/strapmod?555000000000000022CC1C00AD515A3EC0570E142D4A64080049C700030114207A8900A00300000 0150E2A3186272E16

just plug in your own 1500, 1625, or 1750

On that doreymills page there is no readme info guide how to exactly use it Sad
Useless

It may not be designed for newbs. I didn't design it but I find it easy and very useful. Like I said earlier you plug (copy) the strap you wanna mod into the tool (overwrite the default strap in the URL) and use the modded strap (the bottom of the 2 on the output page)
full member
Activity: 224
Merit: 102
What are  the dual mine speeds? (stock and modded). All topics only mention ETH mining..

I've been continuing to tweak and also optimizing for dual mining.

So far:

Eth: 30.5 Mh/s
Dcr: 1130 MH/s
VDDC: 0.877
Core: 1300
Mem: 2100
Mem voltage: 0.9
Strap: Custom mix
Mem Errors: 0/min
Power: 125W

NOTE: If you don't undervolt/limit power, it easily dual mines 30.5 MH/s + 1450 MH/s Dcr


Can you post the custom timings string? These of course are the same chips as before some optimum strings have already been found, but I like this one due to only needing 2100 MHz Smiley Very nice target to get 30.5 MHs


Can use 0150E2A3186272E16">http://doreymills.ca/cgi-bin/strapmod?555000000000000022CC1C00AD515A3EC0570E142D4A64080049C700030114207A8900A00300000 0150E2A3186272E16

just plug in your own 1500, 1625, or 1750

On that doreymills page there is no readme info guide how to exactly use it Sad
Useless
full member
Activity: 219
Merit: 100

Can you post the custom timings string? These of course are the same chips as before some optimum strings have already been found, but I like this one due to only needing 2100 MHz Smiley Very nice target to get 30.5 MHs


Its Samsung memory using Uber Mix straps from the Polaris Bios Editing main thread (google).
Pages:
Jump to: