My second ZEC + XMR+ ETH thread builds info links thoughts and photos. - page 65.

ps_jb

hero member

Activity: 742

Merit: 500

Quote from: philipma1957 on November 05, 2016, 01:54:24 PM

My reasoning is even with 35-45 for a gpu the i5 6400t does 20h

the 19.9h below cost me 35 watts . so far cpu mining on zcash is not terrible compared to gpu mining.

Phil you have to think about Dual CPU MB and two Intel 2011-v3 CPUs (20 cores in total)

philipma1957

legendary

Activity: 4256

Merit: 8551

'The right to privacy matters'

Quote from: ps_jb on November 05, 2016, 01:40:59 PM

Quote from: xleejohnx on November 05, 2016, 12:52:59 PM

Y'all holding any or selling off as it comes?
I'm thinking half sale and half hold

I'm thinking to keep all until full blocks will be mined. Price may stabilizes around 1.5 BTC

what I have done is continue to mine some eth I fully sell that. about 1 block every 2.5 days.

I may let zcash just stack bigger.

My reasoning is even with 35-45 for a gpu the i5 6400t does 20h

the 19.9h below cost me 35 watts . so far cpu mining on zcash is not terrible compared to gpu mining.

So this could help the value of zcash

of course if it crashes I still have my eth coin running.

ps_jb

hero member

Activity: 742

Merit: 500

Quote from: xleejohnx on November 05, 2016, 12:52:59 PM

Y'all holding any or selling off as it comes?
I'm thinking half sale and half hold

I'm thinking to keep all until full blocks will be mined. Price may stabilizes around 1.5 BTC

LoneRangir

hero member

Activity: 615

Merit: 500

Quote from: xleejohnx on November 05, 2016, 12:52:59 PM

Quote from: LoneRangir on November 05, 2016, 12:37:04 PM

Quote from: philipma1957 on November 05, 2016, 12:27:32 PM

Quote from: xleejohnx on November 05, 2016, 11:37:05 AM

Quote from: LoneRangir on November 05, 2016, 11:09:05 AM

Quote from: ps_jb on November 05, 2016, 11:00:27 AM

Quote from: LoneRangir on November 05, 2016, 10:52:20 AM

I recently switched from suprnova over to flypool. I mine directly to my bittrex zec address. I have auto payouts set, and according to the flypool payout page, I should have 4 payouts. However, when I log into bittrex, I have only received 1 payment from flypool. It's been quite a few hours, no pending deposits, no available zec to sell. Anyone have similar latency issues mining directly to an exchange address? Up until my switch yesterday, I mined directly to this same address from suprnova, and I have had not issues. Any input welcome...

I mine to polo address from the day 0

Except two small issues with manual payments I've got all of them timely

I'm switching some (all?) rigs back to suprnova until the payments show up. I like the flypool status interface so much better. It gets old logging into suprnova to check on everything.

I read that Bittrex is having a problem with their zec wallet

It is in Maintainence.

I boosted my payout number from .01 to .10. I am up to .06

As soon as wallet leaves Maintainence I will change from .1 to .02 and payment will shift

I now see the maintenance symbol next to the wallet. I did not see it before. Better have more coffee Cheesy

Y'all holding any or selling off as it comes?
I'm thinking half sale and half hold

I am selling it all. The price is on a pretty steady downward trend. Things may change when we reach full block payouts in a few weeks' time.

xleejohnx

hero member

Activity: 672

Merit: 500

Quote from: LoneRangir on November 05, 2016, 12:37:04 PM

Quote from: philipma1957 on November 05, 2016, 12:27:32 PM

Quote from: xleejohnx on November 05, 2016, 11:37:05 AM

Quote from: LoneRangir on November 05, 2016, 11:09:05 AM

Quote from: ps_jb on November 05, 2016, 11:00:27 AM

Quote from: LoneRangir on November 05, 2016, 10:52:20 AM

I recently switched from suprnova over to flypool. I mine directly to my bittrex zec address. I have auto payouts set, and according to the flypool payout page, I should have 4 payouts. However, when I log into bittrex, I have only received 1 payment from flypool. It's been quite a few hours, no pending deposits, no available zec to sell. Anyone have similar latency issues mining directly to an exchange address? Up until my switch yesterday, I mined directly to this same address from suprnova, and I have had not issues. Any input welcome...

I mine to polo address from the day 0

Except two small issues with manual payments I've got all of them timely

I'm switching some (all?) rigs back to suprnova until the payments show up. I like the flypool status interface so much better. It gets old logging into suprnova to check on everything.

I read that Bittrex is having a problem with their zec wallet

It is in Maintainence.

I boosted my payout number from .01 to .10. I am up to .06

As soon as wallet leaves Maintainence I will change from .1 to .02 and payment will shift

I now see the maintenance symbol next to the wallet. I did not see it before. Better have more coffee Cheesy

Y'all holding any or selling off as it comes?
I'm thinking half sale and half hold

LoneRangir

hero member

Activity: 615

Merit: 500

Quote from: philipma1957 on November 05, 2016, 12:27:32 PM

Quote from: xleejohnx on November 05, 2016, 11:37:05 AM

Quote from: LoneRangir on November 05, 2016, 11:09:05 AM

Quote from: ps_jb on November 05, 2016, 11:00:27 AM

Quote from: LoneRangir on November 05, 2016, 10:52:20 AM

I recently switched from suprnova over to flypool. I mine directly to my bittrex zec address. I have auto payouts set, and according to the flypool payout page, I should have 4 payouts. However, when I log into bittrex, I have only received 1 payment from flypool. It's been quite a few hours, no pending deposits, no available zec to sell. Anyone have similar latency issues mining directly to an exchange address? Up until my switch yesterday, I mined directly to this same address from suprnova, and I have had not issues. Any input welcome...

I mine to polo address from the day 0

Except two small issues with manual payments I've got all of them timely

I'm switching some (all?) rigs back to suprnova until the payments show up. I like the flypool status interface so much better. It gets old logging into suprnova to check on everything.

I read that Bittrex is having a problem with their zec wallet

It is in Maintainence.

I boosted my payout number from .01 to .10. I am up to .06

As soon as wallet leaves Maintainence I will change from .1 to .02 and payment will shift

I now see the maintenance symbol next to the wallet. I did not see it before. Better have more coffee Cheesy

philipma1957

legendary

Activity: 4256

Merit: 8551

'The right to privacy matters'

Quote from: xleejohnx on November 05, 2016, 11:37:05 AM

Quote from: LoneRangir on November 05, 2016, 11:09:05 AM

Quote from: ps_jb on November 05, 2016, 11:00:27 AM

Quote from: LoneRangir on November 05, 2016, 10:52:20 AM

I recently switched from suprnova over to flypool. I mine directly to my bittrex zec address. I have auto payouts set, and according to the flypool payout page, I should have 4 payouts. However, when I log into bittrex, I have only received 1 payment from flypool. It's been quite a few hours, no pending deposits, no available zec to sell. Anyone have similar latency issues mining directly to an exchange address? Up until my switch yesterday, I mined directly to this same address from suprnova, and I have had not issues. Any input welcome...

I mine to polo address from the day 0

Except two small issues with manual payments I've got all of them timely

I'm switching some (all?) rigs back to suprnova until the payments show up. I like the flypool status interface so much better. It gets old logging into suprnova to check on everything.

I read that Bittrex is having a problem with their zec wallet

It is in Maintainence.

I boosted my payout number from .01 to .10. I am up to .06

As soon as wallet leaves Maintainence I will change from .1 to .02 and payment will shift

LoneRangir

hero member

Activity: 615

Merit: 500

Quote from: xleejohnx on November 05, 2016, 11:37:05 AM

Quote from: LoneRangir on November 05, 2016, 11:09:05 AM

Quote from: ps_jb on November 05, 2016, 11:00:27 AM

Quote from: LoneRangir on November 05, 2016, 10:52:20 AM

I recently switched from suprnova over to flypool. I mine directly to my bittrex zec address. I have auto payouts set, and according to the flypool payout page, I should have 4 payouts. However, when I log into bittrex, I have only received 1 payment from flypool. It's been quite a few hours, no pending deposits, no available zec to sell. Anyone have similar latency issues mining directly to an exchange address? Up until my switch yesterday, I mined directly to this same address from suprnova, and I have had not issues. Any input welcome...

I mine to polo address from the day 0

Except two small issues with manual payments I've got all of them timely

I'm switching some (all?) rigs back to suprnova until the payments show up. I like the flypool status interface so much better. It gets old logging into suprnova to check on everything.

I read that Bittrex is having a problem with their zec wallet

Okay, that would make some sense. I just switched a few rigs back over, and triggered an auto-payout from suprnova, too, and it did not show up.

xleejohnx

hero member

Activity: 672

Merit: 500

Quote from: LoneRangir on November 05, 2016, 11:09:05 AM

Quote from: ps_jb on November 05, 2016, 11:00:27 AM

Quote from: LoneRangir on November 05, 2016, 10:52:20 AM

I recently switched from suprnova over to flypool. I mine directly to my bittrex zec address. I have auto payouts set, and according to the flypool payout page, I should have 4 payouts. However, when I log into bittrex, I have only received 1 payment from flypool. It's been quite a few hours, no pending deposits, no available zec to sell. Anyone have similar latency issues mining directly to an exchange address? Up until my switch yesterday, I mined directly to this same address from suprnova, and I have had not issues. Any input welcome...

I mine to polo address from the day 0

Except two small issues with manual payments I've got all of them timely

I'm switching some (all?) rigs back to suprnova until the payments show up. I like the flypool status interface so much better. It gets old logging into suprnova to check on everything.

I read that Bittrex is having a problem with their zec wallet

LoneRangir

hero member

Activity: 615

Merit: 500

Quote from: ps_jb on November 05, 2016, 11:00:27 AM

Quote from: LoneRangir on November 05, 2016, 10:52:20 AM

I recently switched from suprnova over to flypool. I mine directly to my bittrex zec address. I have auto payouts set, and according to the flypool payout page, I should have 4 payouts. However, when I log into bittrex, I have only received 1 payment from flypool. It's been quite a few hours, no pending deposits, no available zec to sell. Anyone have similar latency issues mining directly to an exchange address? Up until my switch yesterday, I mined directly to this same address from suprnova, and I have had not issues. Any input welcome...

I mine to polo address from the day 0

Except two small issues with manual payments I've got all of them timely

I'm switching some (all?) rigs back to suprnova until the payments show up. I like the flypool status interface so much better. It gets old logging into suprnova to check on everything.

ps_jb

hero member

Activity: 742

Merit: 500

Quote from: LoneRangir on November 05, 2016, 10:52:20 AM

I recently switched from suprnova over to flypool. I mine directly to my bittrex zec address. I have auto payouts set, and according to the flypool payout page, I should have 4 payouts. However, when I log into bittrex, I have only received 1 payment from flypool. It's been quite a few hours, no pending deposits, no available zec to sell. Anyone have similar latency issues mining directly to an exchange address? Up until my switch yesterday, I mined directly to this same address from suprnova, and I have had not issues. Any input welcome...

I mine to polo address from the day 0

Except two small issues with manual payments I've got all of them timely

LoneRangir

hero member

Activity: 615

Merit: 500

I recently switched from suprnova over to flypool. I mine directly to my bittrex zec address. I have auto payouts set, and according to the flypool payout page, I should have 4 payouts. However, when I log into bittrex, I have only received 1 payment from flypool. It's been quite a few hours, no pending deposits, no available zec to sell. Anyone have similar latency issues mining directly to an exchange address? Up until my switch yesterday, I mined directly to this same address from suprnova, and I have had not issues. Any input welcome...

ps_jb

hero member

Activity: 742

Merit: 500

Quote from: AriesIV10 on November 05, 2016, 06:46:41 AM

The case is a Rosewill Server Chassis/Server Case/Rackmount Case, 4U Metal Rack Mount Server Chassis with 8 Bays E-ATX https://amzn.com/B0056OUTBK
Not much custom work other than removing the cpu bays, making an angle bracket to hold the gpus and moving the middle fans back. I have solved any heat issue but the result is the air flow is from the back to the front. It looks cool though! I had to try.

Does it require much work? This case costs 90$, while many open frames are around 100$ (and no fans)

xleejohnx

hero member

Activity: 672

Merit: 500

Quote from: AriesIV10 on November 05, 2016, 06:46:41 AM

Quote from: generalt on November 04, 2016, 10:14:05 PM

Quote from: AriesIV10 on November 04, 2016, 12:14:35 PM

Quote from: arielbit on November 04, 2016, 07:40:55 AM

@ AriesIV10

i think your two case fans (beside the motherboard) should direct air the other way, from external air -> cpu-board -> gpus.. besides the hot air from the cards will likely be sucked in by the PSU too.

You are exactly correct. They are backwards. This is the way the server case had the mobo location. Heat is an issue. I am changing it around.

The case looks awesome. Can I ask what case that is and how much of the work on the case is custom?

The case is a Rosewill Server Chassis/Server Case/Rackmount Case, 4U Metal Rack Mount Server Chassis with 8 Bays E-ATX https://amzn.com/B0056OUTBK
Not much custom work other than removing the cpu bays, making an angle bracket to hold the gpus and moving the middle fans back. I have solved any heat issue but the result is the air flow is from the back to the front. It looks cool though! I had to try.

I like how this looks.. I might look into this.

AriesIV10

legendary

Activity: 1260

Merit: 1006

Mine for a Bit

Quote from: generalt on November 04, 2016, 10:14:05 PM

Quote from: AriesIV10 on November 04, 2016, 12:14:35 PM

Quote from: arielbit on November 04, 2016, 07:40:55 AM

@ AriesIV10

i think your two case fans (beside the motherboard) should direct air the other way, from external air -> cpu-board -> gpus.. besides the hot air from the cards will likely be sucked in by the PSU too.

You are exactly correct. They are backwards. This is the way the server case had the mobo location. Heat is an issue. I am changing it around.

The case looks awesome. Can I ask what case that is and how much of the work on the case is custom?

The case is a Rosewill Server Chassis/Server Case/Rackmount Case, 4U Metal Rack Mount Server Chassis with 8 Bays E-ATX https://amzn.com/B0056OUTBK
Not much custom work other than removing the cpu bays, making an angle bracket to hold the gpus and moving the middle fans back. I have solved any heat issue but the result is the air flow is from the back to the front. It looks cool though! I had to try.

arielbit

legendary

Activity: 3416

Merit: 1059

ever since i started gpu mining, i haven't used dummy plugs and i didn't bother reading what's causing the problem, because i don't have it lol

btw i have a monitor that i plug when remote troubleshooting is not possible, that's all.

HerbPean

legendary

Activity: 1638

Merit: 1005

Quote from: fullzero on November 04, 2016, 11:24:40 PM

Quote from: HerbPean on November 04, 2016, 10:07:49 PM

Quote from: HerbPean on November 04, 2016, 06:49:43 PM

Quote from: Redrose on November 04, 2016, 06:18:25 PM

Quote from: HerbPean on November 04, 2016, 06:09:41 PM

I reistalled win 10 until I use ETHOS.

I tried to install Crimson 15.12 like Claymore say ... I don't have the video option in the list ?

Anyone had that issue ?

Should I just install 16.9.2 ?

What are your graphic cards ? Because even if Claymore said to use 15.12, he also said to use the latest ones for some cards.

RX 470

I guess it's the latest ... just wanted to be sure before installed some shit again Tongue

thanks

Brand new Win 10 installation, latest driver.

Same behavior, GPU 1 Hang most of time after x hours.

Or process crashes right off the bat, GPU doesn't start.

Hard to believe this is that hard to have a minimum of stability.

I will try ETHos, but now with Claymore... I might just use 2 Mobo 3 cards each

With ZEC mining; I have found AMD cards tend to soft crash less (almost not at all) if you leave a monitor actively displaying or use a dummy plug. This is especially true for multi card rigs.

Reminds me of wayback. You used to have to make your own dummy plugs; now you can buy hdmi dummy plugs on Amazon. I recommend you try leaving a monitor connected/on with the rig; if it is ok, order some dummy plugs (only need 1 for the primary card per rig).

I leave the monitor open.

GPU 1 is always the one who cause me trouble.

I will try to pin point that GPU and use another riser.

fullzero

legendary

Activity: 1260

Merit: 1009

Quote from: HerbPean on November 04, 2016, 10:07:49 PM

Quote from: HerbPean on November 04, 2016, 06:49:43 PM

Quote from: Redrose on November 04, 2016, 06:18:25 PM

Quote from: HerbPean on November 04, 2016, 06:09:41 PM

I reistalled win 10 until I use ETHOS.

I tried to install Crimson 15.12 like Claymore say ... I don't have the video option in the list ?

Anyone had that issue ?

Should I just install 16.9.2 ?

What are your graphic cards ? Because even if Claymore said to use 15.12, he also said to use the latest ones for some cards.

RX 470

I guess it's the latest ... just wanted to be sure before installed some shit again Tongue

thanks

Brand new Win 10 installation, latest driver.

Same behavior, GPU 1 Hang most of time after x hours.

Or process crashes right off the bat, GPU doesn't start.

Hard to believe this is that hard to have a minimum of stability.

I will try ETHos, but now with Claymore... I might just use 2 Mobo 3 cards each

With ZEC mining; I have found AMD cards tend to soft crash less (almost not at all) if you leave a monitor actively displaying or use a dummy plug. This is especially true for multi card rigs.

Reminds me of wayback. You used to have to make your own dummy plugs; now you can buy hdmi dummy plugs on Amazon. I recommend you try leaving a monitor connected/on with the rig; if it is ok, order some dummy plugs (only need 1 for the primary card per rig).

generalt

legendary

Activity: 1096

Merit: 1021

Quote from: AriesIV10 on November 04, 2016, 12:14:35 PM

Quote from: arielbit on November 04, 2016, 07:40:55 AM

@ AriesIV10

i think your two case fans (beside the motherboard) should direct air the other way, from external air -> cpu-board -> gpus.. besides the hot air from the cards will likely be sucked in by the PSU too.

You are exactly correct. They are backwards. This is the way the server case had the mobo location. Heat is an issue. I am changing it around.

The case looks awesome. Can I ask what case that is and how much of the work on the case is custom?

HerbPean

legendary

Activity: 1638

Merit: 1005

Quote from: HerbPean on November 04, 2016, 06:49:43 PM

Quote from: Redrose on November 04, 2016, 06:18:25 PM

Quote from: HerbPean on November 04, 2016, 06:09:41 PM

I reistalled win 10 until I use ETHOS.

I tried to install Crimson 15.12 like Claymore say ... I don't have the video option in the list ?

Anyone had that issue ?

Should I just install 16.9.2 ?

What are your graphic cards ? Because even if Claymore said to use 15.12, he also said to use the latest ones for some cards.

RX 470

I guess it's the latest ... just wanted to be sure before installed some shit again Tongue

thanks

Brand new Win 10 installation, latest driver.

Same behavior, GPU 1 Hang most of time after x hours.

Or process crashes right off the bat, GPU doesn't start.

Hard to believe this is that hard to have a minimum of stability.

I will try ETHos, but now with Claymore... I might just use 2 Mobo 3 cards each

Topic: My second ZEC + XMR+ ETH thread builds info links thoughts and photos. - page 65. (Read 147923 times)