OFFICIAL CGMINER mining software thread for linux/win/osx/mips/arm/r-pi 4.11.0 - page 59.

helipotte

hero member

Activity: 650

Merit: 500

Pick and place? I need more coffee.

Is the blockerupter prisma/tube not enabled in the windows binary download? When I run cgminer 4.9.0 it never detects the tube I have connected with a

CP2102 Uart. The option "bet-clk 25" results in "unrecognized option". I complied it myself in Mingw. This way detects it but I get LIBUSB errors the a crash.

This same setup works fine under Linux but due to hardware placement windows is the only option now, or the crappy controller using a proxy. Never have been

able to get this thing to hash under Windows 7 x64.

krichter1

newbie

Activity: 1

Merit: 0

Hey,
I'd like to discuss an issue regarding cgminer 4.9.0, but not in a 790 page forum thread, of course. Would you mind activating the issue tracker on github.com in order to make issues readable and discussable?

-Kalle

AJinNYC

member

Activity: 84

Merit: 10

Bored with you morons.

Issue was that I was using zero two in the CFLAGS Configure area instead of the letter O and two.

rav3n_pl

legendary

Activity: 1361

Merit: 1003

Don`t panic! Organize!

If configure end up in error make will not work, sudo or not.
Read line prior "can't create executables", or config.log.

Axiste

full member

Activity: 152

Merit: 100

random guess, pretty sure ive come up against that before try:

sudo make

AJinNYC

member

Activity: 84

Merit: 10

Bored with you morons.

Quote from: os2sam on December 24, 2014, 09:02:28 PM

Quote from: AJinNYC on December 24, 2014, 07:08:17 PM

Are there any pre-built linux distros of CGMiner with Gridseed support enable?

CGMiner doesn't support alt coin miners/ing. Did you check in the alt coin forum for a fork that supports this device?

I can't find anything that supports it honestly. BFGMiner is supposed to but it can never detect it. Maybe somebody else will have better luck with it. Anybody want a GridSeed?

Anyway, I need CGMiner for a RockMiner New RBox too.

Anytime I get to the "make" stage it gives the following error:

os2sam

legendary

Activity: 3583

Merit: 1094

Think for yourself

Quote from: AJinNYC on December 24, 2014, 07:08:17 PM

Are there any pre-built linux distros of CGMiner with Gridseed support enable?

CGMiner doesn't support alt coin miners/ing. Did you check in the alt coin forum for a fork that supports this device?

AJinNYC

member

Activity: 84

Merit: 10

Bored with you morons.

Are there any pre-built linux distros of CGMiner with Gridseed support enable? I can't get this to compile at all; GCC is throwhing an error saying it can't compile executables.

luthermarcus

full member

Activity: 213

Merit: 100

Quote from: vayvanne on December 02, 2014, 12:13:55 PM

today, after a few days of stable hashing I have got this:

Quote

cgminer version 4.8.0 - Started: [2014-11-29 14:32:17]
--------------------------------------------------------------------------------
(20s):1.001G (1m):884.7M (5m):777.8M (15m):943.2M (avg):1.501Gh/s
A:0 R:0 HW:10 WU:21.0/m
Connected to localhost diff 40.3G without LP as user vay
Block: 9076b9eb... Diff:40.3G Started: [17:05:12] Best share: 608K
--------------------------------------------------------------------------------
[U ]SB management [P]ool management [S ]ettings [D]isplay options [Q]uit
2: AU3 0 : 225MHz 750mV | 1.086G / 918.8Mh/s WU:12.8/m
--------------------------------------------------------------------------------
[2014-12-02 17:09:02] AU3 0: No valid hashes for over 1 secs, attempting to reset
[2014-12-02 17:09:02] AU3 0 attempted reset got err:(0) LIBUSB_SUCCESS
[2014-12-02 17:09:05] AU3 0: Share above target
[2014-12-02 17:09:06] AU3 0: Share above target
[2014-12-02 17:09:08] AU3 0: No valid hashes for over 1 secs, attempting to reset
[2014-12-02 17:09:08] AU3 0 attempted reset got err:(0) LIBUSB_SUCCESS
[2014-12-02 17:09:09] (20s):1.102G (1m):1.012G (5m):799.5M (15m):963.0M (avg):1.501Gh/s
[2014-12-02 17:09:10] AU3 0: Share above target
[2014-12-02 17:09:12] AU3 0: No valid hashes for over 1 secs, attempting to reset
[2014-12-02 17:09:12] AU3 0 attempted reset got err:(0) LIBUSB_SUCCESS
[2014-12-02 17:09:17] Stored 513 transactions from pool 0
[2014-12-02 17:09:29] (20s):777.5M (1m):839.1M (5m):764.2M (15m):946.9M (avg):1.501Gh/s

Sometimes I get AU3 device right from startup.

I was having a similar problem get a new usb the highter quality the better.

Buchi-88

legendary

Activity: 3990

Merit: 2695

Hello,

anyone have an idea about this failure?

Quote

cgminer version 4.7.1 - Started: [2014-12-22 12:46:13]
-----------------------------------------------------------------------------------------------
(5s):29.66G (1m):29.07G (5m):29.24G (15m):29.28G (avg):29.27Gh/s
A:60553 R:1918 HW:0 WU:412.8/m | ST: 3 SS: 0 NB: 98 LW: 101434 GF: 7 RF: 0
Connected to multiple pools with block change notify
Block: 712d1003... Diff:2.34M Started: [15:19:58] Best share: 79.9K
-----------------------------------------------------------------------------------------------
USB management Pool management Settings Display options Quit
0: BXM 0 : | 3.725G / 3.624Gh/s WU:51.9/m A:7810 R:217 HW:0
1: BXM 1 : | 3.815G / 3.797Gh/s WU:53.2/m A:8606 R:182 HW:0
2: BXM 2 : | 4.018G / 4.003Gh/s WU:56.0/m A:8544 R:274 HW:0
3: BXM 3 : | 3.715G / 3.700Gh/s WU:51.8/m A:7457 R:292 HW:0
4: BXM 4 : | 3.656G / 3.607Gh/s WU:51.1/m A:7342 R:201 HW:0
6: BXM 6 : | 3.732G / 3.667Gh/s WU:51.9/m A:7733 R:249 HW:0
8: BXM 8 : | 3.932G / 3.883Gh/s WU:54.5/m A:4895 R:226 HW:0
9: BXM 9 : | 3.021G / 2.981Gh/s WU:42.1/m A:2103 R:126 HW:0
-----------------------------------------------------------------------------------------------
[2014-12-22 13:38:14] BXM 5: SPI RX error 0, read 55 of 81
[2014-12-22 13:38:14] BXM 5 failure, disabling!
[2014-12-22 13:38:14] BXM 5: SPI TX error -4, sent 0 of 11
[2014-12-22 13:38:14] BXM 5: SPI TX error -4, sent 0 of 12
[2014-12-22 14:30:46] BXM 7: SPI RX error 0, read 0 of 81
[2014-12-22 14:30:46] BXM 7 failure, disabling!
[2014-12-22 14:30:46] BXM 7: SPI TX error -4, sent 0 of 11
[2014-12-22 14:30:46] BXM 7: SPI TX error -4, sent 0 of 12

regards

canford

member

Activity: 89

Merit: 10

Would a command line switch to specifically enable/disable certain Bitmain USB devices be possible? I am running cgminer under Win7x32 with 12 Bitmain U2s. I limit the number of usb devices to 12, and when all goes well the result is:

Then, unpredictably this can happen:

Sometimes you can fix it by quitting and restarting cgminer, other times a reboot is necessary. Obviously not a priority, negligible hash rate I'm maintaining because it's on my desk and I don't want to throw away the gear. The U2s also randomly disappear or go zombie once every few days, so I scheduled regular reboots.

Thanks ckolivas for great software. I've been mining with cgminer for 15 months now. I haven't sold any of the mined BTC, so the fiat return to date is -49%. It is more about supporting something I believe in than trying to make a profit. I'm up to 7 TH/s now, but BTC would have to go back above $640 for the operation to be in the black.

Taugeran

hero member

Activity: 658

Merit: 500

CCNA: There i fixed the internet.

Quote from: -ck on December 07, 2014, 10:34:32 PM

Quote from: Taugeran on December 07, 2014, 10:12:11 AM

@conman @kanoi: I have a core file I'd like you to take a look at, maybe, please?

Code:

#0 0x00041dc4 in usb_perform_transfer (cgpu=0xbe2910, usbdev=, intinfo=, epinfo=, data=0x0, length=0, transferred=0x0, timeout=0, mode=0, cmd=C_REJECTED,
seq=0, cancellable=false, tt=false) at usbutils.c:3061
3061 else if ((endpoint & LIBUSB_ENDPOINT_DIR_MASK) == LIBUSB_ENDPOINT_IN && *transferred)

Hmm, that C_REJECTED command isn't even meant to be something to be sent to the usb as a transfer so no idea how it ends up with that combination - it ends up trying to send nothing. I'll poke around the code and see if there's something obvious.

FWIW, I moved them to a BBB I had an the issue ceased, so assuming it's the as usual buggy Rpi usb/enet driver

rav3n_pl

legendary

Activity: 1361

Merit: 1003

Don`t panic! Organize!

Last cgminer that support GPU was 3.7.x
If you need GPU mining go for sgminer fork: https://github.com/sgminer-dev/sgminer

os2sam

legendary

Activity: 3583

Merit: 1094

Think for yourself

Quote from: splat44 on December 19, 2014, 01:41:04 PM

Does support litecoin mining via cgminer 4.8?

After seeing possible options, I see no option using scrypt as oldest version!
All previous version lower than 4.0 has been removed!

Any feedback?

Sounds like you answered your own question. I think GPU and scrypt was discontinued around 3.8 or 3.8.2.

From the Top Post

Quote from: -ck on July 12, 2011, 10:02:53 PM

FAQ

Q: Can I mine scrypt with FPGAs or ASICs?
A: No.

splat44

sr. member

Activity: 384

Merit: 250

Does support litecoin mining via cgminer 4.8?

After seeing possible options, I see no option using scrypt as oldest version!
All previous version lower than 4.0 has been removed!

Any feedback?

alexhartwig01

newbie

Activity: 2

Merit: 0

http://i130.photobucket.com/albums/p241/shadowdamon/CgminerError.png

Still the same error with newer version.

-ck

legendary

Activity: 4088

Merit: 1631

Ruu \o/

Quote from: splat44 on December 18, 2014, 09:40:47 PM

Hi,

I need to inform you that latest AMD radeon driver especially the OMEGA file revision number isn't compatible with cgminer 4.8 as it crashes my GPU!

Until developers test cgminer with latest AMD driver as I specified, do not install that file revision for the time being!

That's fascinating considering there's no GPU code in cgminer. I don't miss having to deal with AMD's drivers one bit.

os2sam

legendary

Activity: 3583

Merit: 1094

Think for yourself

Quote from: hurricandave on December 18, 2014, 10:01:59 PM

GPU Mining Huh

Yeah, those were the days. Kinda miss them. Not the noise though.

hurricandave

legendary

Activity: 966

Merit: 1003

GPU Mining Huh

splat44

sr. member

Activity: 384

Merit: 250

Hi,

I need to inform you that latest AMD radeon driver especially the OMEGA file revision number isn't compatible with cgminer 4.8 as it crashes my GPU!

Until developers test cgminer with latest AMD driver as I specified, do not install that file revision for the time being!

Topic: OFFICIAL CGMINER mining software thread for linux/win/osx/mips/arm/r-pi 4.11.0 - page 59. (Read 5805649 times)