Re: [ANN] Technobit HEX16A2 - 24 Ghs - 50 EUR 48 h shippment - page 46.

mudge

member

Activity: 92

Merit: 10

I really hope mine come with molex conectors. I realy don't want to go messing with striping wires

Zich

legendary

Activity: 1190

Merit: 1000

Quote from: loshia on December 23, 2013, 07:08:44 AM

Quote from: PummelHummel on December 23, 2013, 06:50:56 AM

My HEX16A2 finally arrived today (although it was an order that was supposed to be shipped 3rd. wekk of November...) - really dissapointing.

Also it does not have the molex power supply as described just a tiny screw terminals without any markings whatsover. This means I dont know which line is the +12V and which one the ground port.

Does anyone of you guys have an Idea?

Hey,
1. If you do have multimeter around you can check it out. There must be a shortcut between heatsink and minus.
2. Do not count on it unless confirmed but plus is the closest one to the boarder of the board

I always measure it with connectivity tester before add power Cool

Please be careful when tighten or loosen since there is 1 capacitor closed with terminal Grin

Man, i post so many but my activity still 196 Huh

loshia

legendary

Activity: 1610

Merit: 1000

Quote from: PummelHummel on December 23, 2013, 06:50:56 AM

My HEX16A2 finally arrived today (although it was an order that was supposed to be shipped 3rd. wekk of November...) - really dissapointing.

Also it does not have the molex power supply as described just a tiny screw terminals without any markings whatsover. This means I dont know which line is the +12V and which one the ground port.

Does anyone of you guys have an Idea?

Hey,
1. If you do have multimeter around you can check it out. There must be a shortcut between heatsink and minus.
2. Do not count on it unless confirmed but plus is the closest one to the boarder of the board

marto74

hero member

Activity: 728

Merit: 500

So this is December shipment
It will be shipped on 27-th or 30-th

Best Martin

Quote from: blitzwilli1 on December 23, 2013, 07:03:17 AM

ORDER REFERENCE DATE TOTAL PRICE PAYMENT: STATUS INVOICE
NLTALAEYM 2013-11-23 xxx bitpay Payment accepted Invoice PDF details

Quote from: marto74 on December 23, 2013, 06:06:24 AM

Quote from: blitzwilli1 on December 23, 2013, 05:55:51 AM

I understand that correctly?
they have ordered on 04.12.2013 and it was already Sent?

I ordered on 23.11.2013 and it is still in the STATUS Payment accepted
I am very disappointed

Quote from: iFA88 on December 22, 2013, 08:09:52 AM

Dear Marto!
I sent 2 emails to you but i did not get any answer from you.
I have a few questions to you.
I ordered in 4th of December 2x3 boards. Between two orders is 1-2 hour. First: SNOUOBCFN is with DPD economy shipment, the other is: VUMCRQDKX . Please merge this two order to one with DPD shipment.Thank you
I have a question: I ordered it 04-12-2013 and my question is when will be ship?
There is any solution to refund? In case yes, Get I my money back in BTC or USD?

Thanks for the answer!

Best Regards:
-Andor 'iFA88' Rajci

Code:

VUMCRQDKX 2013-12-04 899,90€ bitpay Payment accepted Invoice PDF details Reorder
SNOUOBCFN 2013-12-04 927,90€ bitpay Payment accepted Invoice PDF details Reorder

order ref please

Again by your order date your order is December shipment and there are 2 more working days here 27-th and 30-th
We are catching up with backlog still and doing our best to finish the 2013 with all 2013 shipment orders shipped

Martin

marto74

hero member

Activity: 728

Merit: 500

Quote from: PummelHummel on December 23, 2013, 06:50:56 AM

My HEX16A2 finally arrived today (although it was an order that was supposed to be shipped 3rd. wekk of November...) - really dissapointing.

Also it does not have the molex power supply as described just a tiny screw terminals without any markings whatsover. This means I dont know which line is the +12V and which one the ground port.

Does anyone of you guys have an Idea?

look here
http://technobit.eu/index.php?fc=module&module=clblog&controller=posts&post=4

blitzwilli1

newbie

Activity: 45

Merit: 0

ORDER REFERENCE DATE TOTAL PRICE PAYMENT: STATUS INVOICE
NLTALAEYM 2013-11-23 xxx bitpay Payment accepted Invoice PDF details

Quote from: marto74 on December 23, 2013, 06:06:24 AM

Quote from: blitzwilli1 on December 23, 2013, 05:55:51 AM

I understand that correctly?
they have ordered on 04.12.2013 and it was already Sent?

I ordered on 23.11.2013 and it is still in the STATUS Payment accepted
I am very disappointed

Quote from: iFA88 on December 22, 2013, 08:09:52 AM

Dear Marto!
I sent 2 emails to you but i did not get any answer from you.
I have a few questions to you.
I ordered in 4th of December 2x3 boards. Between two orders is 1-2 hour. First: SNOUOBCFN is with DPD economy shipment, the other is: VUMCRQDKX . Please merge this two order to one with DPD shipment.Thank you
I have a question: I ordered it 04-12-2013 and my question is when will be ship?
There is any solution to refund? In case yes, Get I my money back in BTC or USD?

Thanks for the answer!

Best Regards:
-Andor 'iFA88' Rajci

Code:

VUMCRQDKX 2013-12-04 899,90€ bitpay Payment accepted Invoice PDF details Reorder
SNOUOBCFN 2013-12-04 927,90€ bitpay Payment accepted Invoice PDF details Reorder

order ref please

Again by your order date your order is December shipment and there are 2 more working days here 27-th and 30-th
We are catching up with backlog still and doing our best to finish the 2013 with all 2013 shipment orders shipped

Martin

PummelHummel

newbie

Activity: 35

Merit: 0

My HEX16A2 finally arrived today (although it was an order that was supposed to be shipped 3rd. wekk of November...) - really dissapointing.

Also it does not have the molex power supply as described just a tiny screw terminals without any markings whatsover. This means I dont know which line is the +12V and which one the ground port.

Does anyone of you guys have an Idea?

marto74

hero member

Activity: 728

Merit: 500

Quote from: ?? on ??

hi marto

have the nanofurys that you were selling on technobit for 48 euro and afterwards 52 euro been fully produced and ready for pickup/despatch

please update the circumstance here

(just posting in a few places as i am not sure where you would see it. not trolling. will delete afterwards)

thank you

No all our products are preorder with 3-4 weeks delivery , that we are a little bit behind @ the moment.
@ the moment you can only order nanos with your chips for assembly service and this will be filled in 3-4 weeks

Best Martin

marto74

hero member

Activity: 728

Merit: 500

Quote from: blitzwilli1 on December 23, 2013, 05:55:51 AM

I understand that correctly?
they have ordered on 04.12.2013 and it was already Sent?

I ordered on 23.11.2013 and it is still in the STATUS Payment accepted
I am very disappointed

Quote from: iFA88 on December 22, 2013, 08:09:52 AM

Dear Marto!
I sent 2 emails to you but i did not get any answer from you.
I have a few questions to you.
I ordered in 4th of December 2x3 boards. Between two orders is 1-2 hour. First: SNOUOBCFN is with DPD economy shipment, the other is: VUMCRQDKX . Please merge this two order to one with DPD shipment.Thank you
I have a question: I ordered it 04-12-2013 and my question is when will be ship?
There is any solution to refund? In case yes, Get I my money back in BTC or USD?

Thanks for the answer!

Best Regards:
-Andor 'iFA88' Rajci

Code:

VUMCRQDKX 2013-12-04 899,90€ bitpay Payment accepted Invoice PDF details Reorder
SNOUOBCFN 2013-12-04 927,90€ bitpay Payment accepted Invoice PDF details Reorder

order ref please

Again by your order date your order is December shipment and there are 2 more working days here 27-th and 30-th
We are catching up with backlog still and doing our best to finish the 2013 with all 2013 shipment orders shipped

Martin

blitzwilli1

newbie

Activity: 45

Merit: 0

I understand that correctly?
they have ordered on 04.12.2013 and it was already Sent?

I ordered on 23.11.2013 and it is still in the STATUS Payment accepted
I am very disappointed

Quote from: iFA88 on December 22, 2013, 08:09:52 AM

Dear Marto!
I sent 2 emails to you but i did not get any answer from you.
I have a few questions to you.
I ordered in 4th of December 2x3 boards. Between two orders is 1-2 hour. First: SNOUOBCFN is with DPD economy shipment, the other is: VUMCRQDKX . Please merge this two order to one with DPD shipment.Thank you
I have a question: I ordered it 04-12-2013 and my question is when will be ship?
There is any solution to refund? In case yes, Get I my money back in BTC or USD?

Thanks for the answer!

Best Regards:
-Andor 'iFA88' Rajci

Code:

VUMCRQDKX 2013-12-04 899,90€ bitpay Payment accepted Invoice PDF details Reorder
SNOUOBCFN 2013-12-04 927,90€ bitpay Payment accepted Invoice PDF details Reorder

Zich

legendary

Activity: 1190

Merit: 1000

HEX16A & nanofury work great on TPLINK TL-MR3020 using technoBTCit milestone release 0.1.3 image while waiting for HEX16A2 that ordered on December 4th, 2013 Grin

Zich

legendary

Activity: 1190

Merit: 1000

Quote from: loshia on December 22, 2013, 07:26:48 AM

b

Quote from: Zich on December 22, 2013, 05:32:07 AM

Quote from: marto74 on December 22, 2013, 05:24:53 AM

Quote from: Zich on December 21, 2013, 08:38:32 PM

marto, i hope you not forget to upload TPLINK image Cheesy

Done

technobit.eu/0_1_3.rar

0.1.3 Milestone release - Nanfury support is added with native libusb api. No hid api's are required!
* cgminer ./autegen.sh --enable-hexmineru to add Nanos' manufactured by TechnoBIT known as HEXu
* cgminer --hexmineru-frequency command line to set chip frequency - range 1-62
* cgminer Added to default /etc/config/cgminer Factory default or web Save+Apply is required for changes to be applied!
* cgminer updated to 3.8.5 rev afe7710858e4ce28bb60f6ae6e167a18d687634f
* cgminer patch to cgminer 3.8.5 rev afe7710858e4ce28bb60f6ae6e167a18d687634f.patch - various code cleanup and optimization needs to be done
* hotplugd added hotplug support for HEXu in /udev/rules.d/01-cgminer.rules. Factory default is required for changes to be applied!
* openwrt updated to r39151

Wonderful, Thanks marto Grin

But the link in website going to 404 because double address: http://technobit.eu/technobit.eu/0_1_3.rar
Time to flash new firmware.

Try again

It works fine for me cclick link in marto's post
http://technobit.eu/0_1_3.rar

Sorry, i forgot to add at "technobit website" Cheesy

that not work because of double address Grin

stiffla

member

Activity: 77

Merit: 10

I managed to get the board up running with ubuntu on a notebook with this already compiled version of cgminer -> https://bitcointalk.org/index.php?topic=355323.40 from user 2GOOD.

I tried to configure it with all options and also only with hexminerc enabled on raspberry pi with debian.
Nevertheless, the "make" process always fails

Code:

CC cgminer-usbutils.o
CC cgminer-driver-hexminerc.o
CCLD cgminer
cgminer-driver-hexminerc.o: In function `hexminerc_send_task':
/home/pi/cgminer/driver-hexminerc.c:72: undefined reference to `SHA256_K'
collect2: ld returned 1 exit status
make[2]: *** [cgminer] Error 1
make[2]: Leaving directory `/home/pi/cgminer'
make[1]: *** [all-recursive] Error 1
make[1]: Leaving directory `/home/pi/cgminer'
make: *** [all] Error 2

loshia

legendary

Activity: 1610

Merit: 1000

Quote from: stiffla on December 22, 2013, 08:59:06 AM

Quote from: Zich on December 22, 2013, 07:08:08 AM

Quote from: Zich on December 22, 2013, 05:16:24 AM

Quote from: stiffla on December 22, 2013, 05:12:27 AM

Okay I will try, Thank you very much

Do I have to start cgminer with any parameters?

That parameter already right. And i hope you not forget to power on the PSU Cheesy

Really sorry dude, i was wrong. You use wrong parameter. I guess that's the real problem.

The correct parameter is:

Code:

sudo ./cgminer --hexminerc-voltage 1100 --hexminerc-options 16:1500 --set_default_to_c

I tried to compile v3.8.5 but it failed. So i switched back to v3.8.1 and used your parameters, but "--set_default_to_c" doesn't work. Here is a screenshot of the verbose debug messages of cgminer. The HEX16A2 just blinks (red and green)

PSU is no name and also tried with an external powered usb hub

Hey,
1. Enable only HexC Avalon2 board by doing ./autogen.sh -enable-hexminerc
2. Triple check if your board is powered 12v use multimeter and measure the power on miles/thermal connector. It should show you 12v

stiffla

member

Activity: 77

Merit: 10

Quote from: Zich on December 22, 2013, 07:08:08 AM

Quote from: Zich on December 22, 2013, 05:16:24 AM

Quote from: stiffla on December 22, 2013, 05:12:27 AM

Okay I will try, Thank you very much

Do I have to start cgminer with any parameters?

That parameter already right. And i hope you not forget to power on the PSU Cheesy

Really sorry dude, i was wrong. You use wrong parameter. I guess that's the real problem.

The correct parameter is:

Code:

sudo ./cgminer --hexminerc-voltage 1100 --hexminerc-options 16:1500 --set_default_to_c

I tried to compile v3.8.5 but it failed. So i switched back to v3.8.1 and used your parameters, but "--set_default_to_c" doesn't work. Here is a screenshot of the verbose debug messages of cgminer. The HEX16A2 just blinks (red and green)

PSU is no name and also tried with an external powered usb hub

iFA88

full member

Activity: 237

Merit: 100

Dear Marto!
I sent 2 emails to you but i did not get any answer from you.
I have a few questions to you.
I ordered in 4th of December 2x3 boards. Between two orders is 1-2 hour. First: SNOUOBCFN is with DPD economy shipment, the other is: VUMCRQDKX . Please merge this two order to one with DPD shipment.Thank you
I have a question: I ordered it 04-12-2013 and my question is when will be ship?
There is any solution to refund? In case yes, Get I my money back in BTC or USD?

Thanks for the answer!

Best Regards:
-Andor 'iFA88' Rajci

Code:

VUMCRQDKX 2013-12-04 899,90€ bitpay Payment accepted Invoice PDF details Reorder
SNOUOBCFN 2013-12-04 927,90€ bitpay Payment accepted Invoice PDF details Reorder

loshia

legendary

Activity: 1610

Merit: 1000

Quote from: stiffla on December 22, 2013, 04:55:29 AM

Quote from: Zich on December 22, 2013, 04:41:32 AM

Quote from: stiffla on December 22, 2013, 04:23:22 AM

Hi guys,

I followed the instructions on page 11 to get the board running with cgminer, but no success so far. Also on windows it was not possible for me the get it running.

The board LED's are blinking sometimes , sometimes not. Has anyone any Idea or had the same problems?
At least it got recognized on my raspberry, but thats all so far.

Could you please tell us you configuration & which miner board(HEX16A, HEX16B, HEX16C, Nanofury)

ohh sorry,
it is the HEX16A2 connected to raspberry pi with debian wheezy, PSU has 16A at 12V, so it should be enough power available.
I tried with cgminer 3.8.1 with patch, board gets recognized but no hashes

i used this command to start cgminer:
sudo ./cgminer --hexminerc-voltage 900 --hexminerc-options 16:540

Wrong no bugs there read Zich post below ...

loshia

legendary

Activity: 1610

Merit: 1000

b

Quote from: Zich on December 22, 2013, 05:32:07 AM

Quote from: marto74 on December 22, 2013, 05:24:53 AM

Quote from: Zich on December 21, 2013, 08:38:32 PM

marto, i hope you not forget to upload TPLINK image Cheesy

Done

technobit.eu/0_1_3.rar

0.1.3 Milestone release - Nanfury support is added with native libusb api. No hid api's are required!
* cgminer ./autegen.sh --enable-hexmineru to add Nanos' manufactured by TechnoBIT known as HEXu
* cgminer --hexmineru-frequency command line to set chip frequency - range 1-62
* cgminer Added to default /etc/config/cgminer Factory default or web Save+Apply is required for changes to be applied!
* cgminer updated to 3.8.5 rev afe7710858e4ce28bb60f6ae6e167a18d687634f
* cgminer patch to cgminer 3.8.5 rev afe7710858e4ce28bb60f6ae6e167a18d687634f.patch - various code cleanup and optimization needs to be done
* hotplugd added hotplug support for HEXu in /udev/rules.d/01-cgminer.rules. Factory default is required for changes to be applied!
* openwrt updated to r39151

Wonderful, Thanks marto Grin

But the link in website going to 404 because double address: http://technobit.eu/technobit.eu/0_1_3.rar
Time to flash new firmware.

Try again

It works fine for me cclick link in marto's post
http://technobit.eu/0_1_3.rar

Zich

legendary

Activity: 1190

Merit: 1000

Quote from: Zich on December 22, 2013, 05:16:24 AM

Quote from: stiffla on December 22, 2013, 05:12:27 AM

Okay I will try, Thank you very much

Do I have to start cgminer with any parameters?

That parameter already right. And i hope you not forget to power on the PSU Cheesy

Really sorry dude, i was wrong. You use wrong parameter. I guess that's the real problem.

The correct parameter is:

Code:

sudo ./cgminer --hexminerc-voltage 1100 --hexminerc-options 16:1500 --set_default_to_c

Zich

legendary

Activity: 1190

Merit: 1000

Quote from: marto74 on December 22, 2013, 05:24:53 AM

Quote from: Zich on December 21, 2013, 08:38:32 PM

marto, i hope you not forget to upload TPLINK image Cheesy

Done

technobit.eu/0_1_3.rar

0.1.3 Milestone release - Nanfury support is added with native libusb api. No hid api's are required!
* cgminer ./autegen.sh --enable-hexmineru to add Nanos' manufactured by TechnoBIT known as HEXu
* cgminer --hexmineru-frequency command line to set chip frequency - range 1-62
* cgminer Added to default /etc/config/cgminer Factory default or web Save+Apply is required for changes to be applied!
* cgminer updated to 3.8.5 rev afe7710858e4ce28bb60f6ae6e167a18d687634f
* cgminer patch to cgminer 3.8.5 rev afe7710858e4ce28bb60f6ae6e167a18d687634f.patch - various code cleanup and optimization needs to be done
* hotplugd added hotplug support for HEXu in /udev/rules.d/01-cgminer.rules. Factory default is required for changes to be applied!
* openwrt updated to r39151

Wonderful, Thanks marto Grin

But the link in website going to 404 because double address: http://technobit.eu/technobit.eu/0_1_3.rar
Time to flash new firmware.

Topic: Re: [ANN] Technobit HEX16A2 - 24 Ghs - 50 EUR 48 h shippment - page 46. (Read 104895 times)