Bitcoin Forum>Bitcoin>Mining>Mining support
Pages:
Author

Topic: repair a T9 + after a bad firmware (lost chain) - page 2. (Read 22784 times)

Ortadan
newbie
Activity: 13
Merit: 0
Re: repair a T9 + after a bad firmware (lost chain)
July 06, 2019, 03:45:34 PM
#55
Hello, I recently bought a damaged T9+ to replace (Fan, controller card) my other antminer and the 3 hasboard present this error:

Code:
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.14.0-xilinx-ge8a2f71-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #82 SMP PREEMPT Tue May 16 19:49:53 CST 2017
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Xilinx Zynq
[    0.000000] cma: CMA: reserved 128 MiB at 16800000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 126976
[    0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map debd8000
[    0.000000]   Normal zone: 992 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 126976 pages, LIFO batch:31
[    0.000000] PERCPU: Embedded 8 pages/cpu @debc1000 s9088 r8192 d15488 u32768
[    0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 125984
[    0.000000] Kernel command line: noinitrd mem=496M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 364356K/507904K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 143548K reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xdf800000 - 0xff000000   ( 504 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xdf000000   ( 496 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc06d1374   (6949 kB)
[    0.000000]       .init : 0xc06d2000 - 0xc0705380   ( 205 kB)
[    0.000000]       .data : 0xc0706000 - 0xc074cf78   ( 284 kB)
[    0.000000]        .bss : 0xc074cf84 - 0xc078d9fc   ( 259 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[    0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] ps7-slcr mapped to df802000
[    0.000000] zynq_clock_init: clkc starts at df802100
[    0.000000] Zynq clock init
[    0.000015] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[    0.000315] ps7-ttc #0 at df804000, irq=43
[    0.000625] Console: colour dummy device 80x30
[    0.000657] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[    0.040211] pid_max: default: 32768 minimum: 301
[    0.040434] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.040455] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.042631] CPU: Testing write buffer coherency: ok
[    0.042978] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.043040] Setting up static identity map for 0x4c4b00 - 0x4c4b58
[    0.043264] L310 cache controller enabled
[    0.043284] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[    0.121039] CPU1: Booted secondary processor
[    0.210231] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.210361] Brought up 2 CPUs
[    0.210381] SMP: Total of 2 processors activated.
[    0.210389] CPU: All CPU(s) started in SVC mode.
[    0.211087] devtmpfs: initialized
[    0.213505] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.214759] regulator-dummy: no parameters
[    0.223745] NET: Registered protocol family 16
[    0.226061] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.228373] cpuidle: using governor ladder
[    0.228386] cpuidle: using governor menu
[    0.235924] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[    0.237463] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.237477] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.237598] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xdf880000
[    0.259526] bio: create slab at 0
[    0.262232] vgaarb: loaded
[    0.262971] SCSI subsystem initialized
[    0.263864] usbcore: registered new interface driver usbfs
[    0.264037] usbcore: registered new interface driver hub
[    0.264265] usbcore: registered new device driver usb
[    0.264788] media: Linux media interface: v0.10
[    0.264956] Linux video capture interface: v2.00
[    0.265197] pps_core: LinuxPPS API ver. 1 registered
[    0.265209] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
[    0.265336] PTP clock support registered
[    0.265691] EDAC MC: Ver: 3.0.0
[    0.266747] Advanced Linux Sound Architecture Driver Initialized.
[    0.269708] DMA-API: preallocated 4096 debug entries
[    0.269724] DMA-API: debugging enabled by kernel config
[    0.269819] Switched to clocksource arm_global_timer
[    0.289887] NET: Registered protocol family 2
[    0.290585] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[    0.290644] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.290729] TCP: Hash tables configured (established 4096 bind 4096)
[    0.290781] TCP: reno registered
[    0.290799] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.290832] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.291082] NET: Registered protocol family 1
[    0.291466] RPC: Registered named UNIX socket transport module.
[    0.291480] RPC: Registered udp transport module.
[    0.291488] RPC: Registered tcp transport module.
[    0.291497] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.291510] PCI: CLS 0 bytes, default 64
[    0.291988] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    0.294075] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.296233] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.296420] msgmni has been set to 967
[    0.297226] io scheduler noop registered
[    0.297239] io scheduler deadline registered
[    0.297282] io scheduler cfq registered (default)
[    0.308907] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[    0.308927] dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[    0.437366] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[    1.005772] console [ttyPS0] enabled
[    1.010119] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to df866000
[    1.017740] [drm] Initialized drm 1.1.0 20060810
[    1.034801] brd: module loaded
[    1.044282] loop: module loaded
[    1.053993] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[    1.059743] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[    1.067728] libphy: XEMACPS mii bus: probed
[    1.072295] ------------- phy_id = 0x3625e62
[    1.077045] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[    1.085976] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.092801] ehci-pci: EHCI PCI platform driver
[    1.100057] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[    1.106863] usbcore: registered new interface driver usb-storage
[    1.113778] mousedev: PS/2 mouse device common for all mice
[    1.119908] i2c /dev entries driver
[    1.126866] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[    1.132397] cpufreq_cpu0: failed to get cpu0 regulator: -19
[    1.138299] Xilinx Zynq CpuIdle Driver started
[    1.143215] sdhci: Secure Digital Host Controller Interface driver
[    1.149311] sdhci: Copyright(c) Pierre Ossman
[    1.153678] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.160542] mmc0: no vqmmc regulator found
[    1.164558] mmc0: no vmmc regulator found
[    1.209863] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[    1.218554] usbcore: registered new interface driver usbhid
[    1.224057] usbhid: USB HID core driver
[    1.228793] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[    1.235090] nand: Micron MT29F2G08ABAEAWP
[    1.239058] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[    1.245002] Bad block table found at page 131008, version 0x01
[    1.251226] Bad block table found at page 130944, version 0x01
[    1.257278] 3 ofpart partitions found on MTD device pl353-nand
[    1.263057] Creating 3 MTD partitions on "pl353-nand":
[    1.268148] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[    1.276248] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[    1.283570] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[    1.292565] TCP: cubic registered
[    1.295800] NET: Registered protocol family 17
[    1.300531] Registering SWP/SWPB emulation handler
[    1.306452] regulator-dummy: disabling
[    1.310853] UBI: attaching mtd1 to ubi0
[    1.838616] UBI: scanning is finished
[    1.850401] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[    1.857456] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    1.864259] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    1.870921] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[    1.877765] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[    1.883772] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[    1.890894] UBI: max/mean erase counter: 126/62, WL threshold: 4096, image sequence number: 248547359
[    1.900086] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[    1.909289] UBI: background thread "ubi_bgt0d" started, PID 1080
[    1.909295] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    1.913327] ALSA device list:
[    1.913331]   No soundcards found.
[    1.929720] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082
[    1.996221] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[    2.002174] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    2.011279] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[    2.021169] UBIFS: reserved for root: 0 bytes (0 KiB)
[    2.026197] UBIFS: media format: w4/r0 (latest is w4/r0), UUID D5E65D66-FDFF-460C-B3DB-A1F2DEB908D8, small LPT model
[    2.037739] VFS: Mounted root (ubifs filesystem) on device 0:11.
[    2.045178] devtmpfs: mounted
[    2.048289] Freeing unused kernel memory: 204K (c06d2000 - c0705000)
[    2.892395] random: dd urandom read with 0 bits of entropy available
[    3.289840]
[    3.289840] bcm54xx_config_init
[    3.899866]
[    3.899866] bcm54xx_config_init
[    7.900703] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[    7.906793] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[   24.777082] In axi fpga driver!
[   24.780183] request_mem_region OK!
[   24.783547] AXI fpga dev virtual address is 0xdf9fc000
[   24.788652] *base_vir_addr = 0xc510
[   24.804571] In fpga mem driver!
[   24.807646] request_mem_region OK!
[   24.811259] fpga mem virtual address is 0xe2000000
[   25.619250]
[   25.619250] bcm54xx_config_init
[   26.249199]
[   26.249199] bcm54xx_config_init
[   30.249679] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[   30.255702] xemacps e000b000.ps7-ethernet: link up (100/FULL)
Detect 512MB control board of XILINX
Miner Type = T9+
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x0000ffff
dsPIC33EP16GS202_reset_pic failed on Chain[1]!
dsPIC33EP16GS202_reset_pic failed on Chain[1]!
dsPIC33EP16GS202_reset_pic failed on Chain[1]!
chain[1] PIC jump to app
dsPIC33EP16GS202_jump_to_app_from_loader failed on Chain[1]!
dsPIC33EP16GS202_jump_to_app_from_loader failed on Chain[1]!
dsPIC33EP16GS202_jump_to_app_from_loader failed on Chain[1]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[1]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[1]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[1]!
Check chain[1] PIC fw version=0xff
dsPIC33EP16GS202_reset_pic failed on Chain[2]!
dsPIC33EP16GS202_reset_pic failed on Chain[2]!
dsPIC33EP16GS202_reset_pic failed on Chain[2]!
chain[2] PIC jump to app
dsPIC33EP16GS202_jump_to_app_from_loader failed on Chain[2]!
dsPIC33EP16GS202_jump_to_app_from_loader failed on Chain[2]!
dsPIC33EP16GS202_jump_to_app_from_loader failed on Chain[2]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[2]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[2]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[2]!
Check chain[2] PIC fw version=0xff
chain[3] PIC jump to app
Check chain[3] PIC fw version=0x90
Chain[J2] will use voltage=930 [1] to open core
set_Voltage_S9_plus_plus_BM1387_54 failed on Chain[1]!

set_Voltage_S9_plus_plus_BM1387_54 failed on Chain[1]!

set_Voltage_S9_plus_plus_BM1387_54 failed on Chain[1]!

Chain[J3] will use voltage=930 [1] to open core
set_Voltage_S9_plus_plus_BM1387_54 failed on Chain[2]!

set_Voltage_S9_plus_plus_BM1387_54 failed on Chain[2]!

set_Voltage_S9_plus_plus_BM1387_54 failed on Chain[2]!

Chain[J4] will use voltage=930 [1] to open core
Chain[J9] will use voltage=930 [1] to open core
Chain[J10] will use voltage=930 [1] to open core
Chain[J11] will use voltage=930 [1] to open core
Chain[J12] will use voltage=930 [1] to open core
Chain[J13] will use voltage=930 [1] to open core
Chain[J14] will use voltage=930 [1] to open core
Fix freq=675 custom_voltage_value=890 custom_voltage_enabled=1 disable_fan_check=0 fixed_frequency=1
Fix freq=675 Chain[1] voltage_pic=7 value=890
 voltage_config=7792714
Fix freq=675 Chain[2] voltage_pic=7 value=890
 voltage_config=7792714
Fix freq=675 Chain[3] voltage_pic=7 value=890
 voltage_config=7792714
Fix freq=675 Chain[8] voltage_pic=7 value=890
 voltage_config=7792714
Fix freq=675 Chain[9] voltage_pic=7 value=890
 voltage_config=7792714
Fix freq=675 Chain[10] voltage_pic=7 value=890
 voltage_config=7792714
Fix freq=675 Chain[11] voltage_pic=7 value=890
 voltage_config=7792714
Fix freq=675 Chain[12] voltage_pic=7 value=890
 voltage_config=7792714
Fix freq=675 Chain[13] voltage_pic=7 value=890
 voltage_config=7792714
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[2]!
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
Chain[J2] has 0 asic
Chain[J3] has 0 asic
Chain[J4] has 0 asic
Chain[J9] has 0 asic
Chain[J10] has 0 asic
Chain[J11] has 0 asic
Chain[J12] has 0 asic
Chain[J13] has 0 asic
Chain[J14] has 0 asic
miner total rate=0GH/s fixed rate=0GH/s

Miner fix freq ...
max freq = 100
set baud=16
restartNum = 2 , auto-reinit enabled...
setStartTimePoint total_tv_start_sys=343 total_tv_end_sys=344
do read_temp_func once...
do check_asic_reg 0x08
Done check_asic_reg
set FAN speed according to: temp_highest=0 temp_top1[PWM_T]=0 temp_top1[TEMP_POS_LOCAL]=0 temp_change=0 fix_fan_steps=0
set full FAN speed...
FAN PWM: 100
read_temp_func Done!
CRC error counter=0

would it be possible to repair the hashboards following the steps of this post by means of a pickit3? if possible I would buy this one: https://www.amazon.com/gp/product/B011BBQQEK. Would that do?

Thank you!
thierry4wd
sr. member
Activity: 446
Merit: 347
Re: repair a T9 + after a bad firmware (lost chain)
June 27, 2019, 10:33:07 AM
#54
hi , i have updated first post with new link.
thierry4wd
sr. member
Activity: 446
Merit: 347
Re: repair a T9 + after a bad firmware (lost chain)
June 07, 2019, 09:23:54 AM
#53
I think you had to miss something in the manipulation ...

I look your kernel log, and i see problem only by "chain 1" ... please unplug all hash board... and plug only one hashboard (other than chain 1) , and try it, and past here your new kernel log ...

If is running good, try to plug 1 hashboard to .... if running good to, reflash with pickit3 the last hashboard .
rotem8866
newbie
Activity: 46
Merit: 0
Re: repair a T9 + after a bad firmware (lost chain)
June 07, 2019, 07:02:28 AM
#52
Just did it and nothing. i also flashed with micro sd (https://support.bitmain.com/hc/en-us/articles/360007577214-T9-Control-Board-Program-Recovery) and then put the firmware you attached. still nothing.

i took other control board from second same machine and its work fine. so i guess i need to send the hash boards to repair.

Thanks!

p.s you have hex for s9 ? i have few boards that not working and i dont have any other working boards here.
thierry4wd
sr. member
Activity: 446
Merit: 347
Re: repair a T9 + after a bad firmware (lost chain)
June 06, 2019, 03:11:41 PM
#51
Hi , at the first time you are resoled the problem "pic 0xff" , and is good !

After, what firmware you have flashed ? try to flash this (2017) https://file11.bitmain.com/shop-product/firmware/Antminer-T9-PLUS-all-201711242319-autofreq-user-Update2UBI-NF.tar.gz , and reset to default the miner ...
rotem8866
newbie
Activity: 46
Merit: 0
Re: repair a T9 + after a bad firmware (lost chain)
June 06, 2019, 06:50:13 AM
#50
Hi.

I followed all procedure and flashing is done successfuly. after reconnecting all again i still have 000000 ghz. see kernel log. (i also flashed the official firmware to the controller.)

what can cause it ?

Code:
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.14.0-xilinx-gb190cb0-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #57 SMP PREEMPT Fri Dec 9 14:49:22 CST 2016
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Xilinx Zynq
[    0.000000] cma: CMA: reserved 128 MiB at 16800000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 126976
[    0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map debd8000
[    0.000000]   Normal zone: 992 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 126976 pages, LIFO batch:31
[    0.000000] PERCPU: Embedded 8 pages/cpu @debc1000 s9088 r8192 d15488 u32768
[    0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 125984
[    0.000000] Kernel command line: noinitrd mem=496M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 364356K/507904K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 143548K reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xdf800000 - 0xff000000   ( 504 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xdf000000   ( 496 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc06d1374   (6949 kB)
[    0.000000]       .init : 0xc06d2000 - 0xc0705380   ( 205 kB)
[    0.000000]       .data : 0xc0706000 - 0xc074cf78   ( 284 kB)
[    0.000000]        .bss : 0xc074cf84 - 0xc078d9fc   ( 259 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[    0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] ps7-slcr mapped to df802000
[    0.000000] zynq_clock_init: clkc starts at df802100
[    0.000000] Zynq clock init
[    0.000015] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[    0.000311] ps7-ttc #0 at df804000, irq=43
[    0.000618] Console: colour dummy device 80x30
[    0.000649] Calibrating delay loop... 1332.01 BogoMIPS (lpj=6660096)
[    0.100251] pid_max: default: 32768 minimum: 301
[    0.100472] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.100492] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.102644] CPU: Testing write buffer coherency: ok
[    0.102978] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.103038] Setting up static identity map for 0x4c4af8 - 0x4c4b50
[    0.103260] L310 cache controller enabled
[    0.103280] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[    0.181033] CPU1: Booted secondary processor
[    0.270229] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.270360] Brought up 2 CPUs
[    0.270379] SMP: Total of 2 processors activated.
[    0.270387] CPU: All CPU(s) started in SVC mode.
[    0.271047] devtmpfs: initialized
[    0.273472] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.274681] regulator-dummy: no parameters
[    0.282358] NET: Registered protocol family 16
[    0.284639] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.286921] cpuidle: using governor ladder
[    0.286934] cpuidle: using governor menu
[    0.294307] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[    0.295821] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.295834] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.295948] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xdf880000
[    0.317424] bio: create slab at 0
[    0.318835] vgaarb: loaded
[    0.319535] SCSI subsystem initialized
[    0.320480] usbcore: registered new interface driver usbfs
[    0.320669] usbcore: registered new interface driver hub
[    0.320889] usbcore: registered new device driver usb
[    0.322168] media: Linux media interface: v0.10
[    0.322331] Linux video capture interface: v2.00
[    0.322572] pps_core: LinuxPPS API ver. 1 registered
[    0.322583] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
[    0.322707] PTP clock support registered
[    0.323067] EDAC MC: Ver: 3.0.0
[    0.324108] Advanced Linux Sound Architecture Driver Initialized.
[    0.326945] DMA-API: preallocated 4096 debug entries
[    0.326960] DMA-API: debugging enabled by kernel config
[    0.327035] Switched to clocksource arm_global_timer
[    0.347152] NET: Registered protocol family 2
[    0.347822] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[    0.347878] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.347963] TCP: Hash tables configured (established 4096 bind 4096)
[    0.348009] TCP: reno registered
[    0.348027] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.348059] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.348295] NET: Registered protocol family 1
[    0.348640] RPC: Registered named UNIX socket transport module.
[    0.348653] RPC: Registered udp transport module.
[    0.348662] RPC: Registered tcp transport module.
[    0.348670] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.348683] PCI: CLS 0 bytes, default 64
[    0.349119] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    0.351135] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.353230] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.353414] msgmni has been set to 967
[    0.354197] io scheduler noop registered
[    0.354210] io scheduler deadline registered
[    0.354263] io scheduler cfq registered (default)
[    0.362865] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[    0.362885] dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[    0.485434] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[    1.054037] console [ttyPS0] enabled
[    1.058335] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to df866000
[    1.065935] [drm] Initialized drm 1.1.0 20060810
[    1.082864] brd: module loaded
[    1.092293] loop: module loaded
[    1.101735] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[    1.107590] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[    1.115343] libphy: XEMACPS mii bus: probed
[    1.119988] ------------- phy_id = 0x3625e62
[    1.124723] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[    1.133354] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.140011] ehci-pci: EHCI PCI platform driver
[    1.147250] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[    1.154046] usbcore: registered new interface driver usb-storage
[    1.160921] mousedev: PS/2 mouse device common for all mice
[    1.167081] i2c /dev entries driver
[    1.173959] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[    1.179510] cpufreq_cpu0: failed to get cpu0 regulator: -19
[    1.185392] Xilinx Zynq CpuIdle Driver started
[    1.190256] sdhci: Secure Digital Host Controller Interface driver
[    1.196353] sdhci: Copyright(c) Pierre Ossman
[    1.200742] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.207517] mmc0: no vqmmc regulator found
[    1.211530] mmc0: no vmmc regulator found
[    1.247056] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[    1.255735] usbcore: registered new interface driver usbhid
[    1.261242] usbhid: USB HID core driver
[    1.265957] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[    1.272258] nand: Micron MT29F2G08ABAEAWP
[    1.276222] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[    1.282163] Bad block table found at page 131008, version 0x01
[    1.288390] Bad block table found at page 130944, version 0x01
[    1.294444] 3 ofpart partitions found on MTD device pl353-nand
[    1.300231] Creating 3 MTD partitions on "pl353-nand":
[    1.305325] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[    1.313373] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[    1.320687] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[    1.329639] TCP: cubic registered
[    1.332877] NET: Registered protocol family 17
[    1.337593] Registering SWP/SWPB emulation handler
[    1.343475] regulator-dummy: disabling
[    1.347819] UBI: attaching mtd1 to ubi0
[    1.873546] UBI: scanning is finished
[    1.885222] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[    1.892302] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    1.899064] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    1.905729] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[    1.912607] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[    1.918587] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[    1.925695] UBI: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 862493722
[    1.934650] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[    1.943867] UBI: background thread "ubi_bgt0d" started, PID 1080
[    1.943872] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    1.947834] ALSA device list:
[    1.947837]   No soundcards found.
[    1.964211] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082
[    1.993337] UBIFS: recovery needed
[    2.219536] UBIFS: recovery completed
[    2.223210] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[    2.229155] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    2.238260] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[    2.248149] UBIFS: reserved for root: 0 bytes (0 KiB)
[    2.253179] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 2A24A8E1-2021-4A54-8A4E-D8E294AE00E5, small LPT model
[    2.264484] VFS: Mounted root (ubifs filesystem) on device 0:11.
[    2.271212] devtmpfs: mounted
[    2.274323] Freeing unused kernel memory: 204K (c06d2000 - c0705000)
[    3.113849] random: dd urandom read with 0 bits of entropy available
[    3.507063]
[    3.507063] bcm54xx_config_init
[    4.117083]
[    4.117083] bcm54xx_config_init
[    7.117908] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[    7.123999] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[   22.100699] In axi fpga driver!
[   22.103768] request_mem_region OK!
[   22.107190] AXI fpga dev virtual address is 0xdf9fc000
[   22.112265] *base_vir_addr = 0xc510
[   22.127201] In fpga mem driver!
[   22.130427] request_mem_region OK!
[   22.133987] fpga mem virtual address is 0xe2000000
[   22.927048]
[   22.927048] bcm54xx_config_init
[   23.557049]
[   23.557049] bcm54xx_config_init
[   26.557913] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[   26.563933] xemacps e000b000.ps7-ethernet: link up (100/FULL)
This is XILINX board. Totalram:       507527168
Detect 512MB control board of XILINX
DETECT HW version=8000c510
miner ID : 80148c806f904814
Miner Type = T9+
AsicType = 1387
real AsicNum = 18
use critical mode to search freq...
get PLUG ON=0x07003f0e
Find hashboard on Chain[1]
Find hashboard on Chain[2]
Find hashboard on Chain[3]
Find hashboard on Chain[8]
Find hashboard on Chain[9]
Find hashboard on Chain[10]
Find hashboard on Chain[11]
Find hashboard on Chain[12]
Find hashboard on Chain[13]
set_reset_allhashboard = 0x0000ffff
dsPIC33EP16GS202_reset_pic failed on Chain[1]! try again...
dsPIC33EP16GS202_reset_pic failed on Chain[1]! try again...
dsPIC33EP16GS202_reset_pic failed on Chain[1]! try again...
chain[1] PIC jump to app
dsPIC33EP16GS202_jump_to_app_from_loader failed on Chain[1]! try again...
dsPIC33EP16GS202_jump_to_app_from_loader failed on Chain[1]! try again...
dsPIC33EP16GS202_jump_to_app_from_loader failed on Chain[1]! try again...
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[1]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[1]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[1]!
Check chain[1] PIC fw version=0xff
chain[2] PIC jump to app
Check chain[2] PIC fw version=0x03
chain[3] PIC jump to app
Check chain[3] PIC fw version=0x03
Chain[1] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x01 0x11 0x11 0x11 0x11 0x11 0x12 0x21 0x11 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x20 0x11 0x12 0x11 0x10 0x11 0x11 0x11 0x11 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
chain[1]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
has freq in PIC, will disable freq setting.
chain[1] has freq in PIC and will jump over...
Chain[1] has core num in PIC
Chain[1] ASIC[1] has core num=1
Chain[1] ASIC[2] has core num=1
Chain[1] ASIC[3] has core num=1
Chain[1] ASIC[4] has core num=1
Chain[1] ASIC[5] has core num=1
Chain[1] ASIC[6] has core num=1
Chain[1] ASIC[7] has core num=1
Chain[1] ASIC[8] has core num=1
Chain[1] ASIC[9] has core num=1
Chain[1] ASIC[10] has core num=1
Chain[1] ASIC[11] has core num=1
Chain[1] ASIC[12] has core num=1
Chain[1] ASIC[13] has core num=2
Chain[1] ASIC[14] has core num=2
Chain[1] ASIC[15] has core num=1
Chain[1] ASIC[16] has core num=1
Chain[1] ASIC[17] has core num=1
Chain[2] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x11 0x11 0x11 0x10 0x11 0x11 0x11 0x11 0x11 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x11 0x11 0x11 0x10 0x01 0x11 0x11 0x20 0x21 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x10 0x10 0x31 0x11 0x11 0x11 0x11 0x01 0x11 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
chain[2]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
has freq in PIC, will disable freq setting.
chain[2] has freq in PIC and will jump over...
Chain[2] has core num in PIC
Chain[2] ASIC[0] has core num=1
Chain[2] ASIC[1] has core num=1
Chain[2] ASIC[2] has core num=1
Chain[2] ASIC[3] has core num=1
Chain[2] ASIC[4] has core num=1
Chain[2] ASIC[5] has core num=1
Chain[2] ASIC[6] has core num=1
Chain[2] ASIC[8] has core num=1
Chain[2] ASIC[9] has core num=1
Chain[2] ASIC[10] has core num=1
Chain[2] ASIC[11] has core num=1
Chain[2] ASIC[12] has core num=1
Chain[2] ASIC[13] has core num=1
Chain[2] ASIC[14] has core num=1
Chain[2] ASIC[15] has core num=1
Chain[2] ASIC[16] has core num=1
Chain[2] ASIC[17] has core num=1
Chain[3] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x01 0x11 0x11 0x31 0x11 0x11 0x11 0x11 0x11 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x11 0x11 0x11 0x11 0x10 0x01 0x11 0x11 0x11 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x11 0x11 0x11 0x10 0x11 0x11 0x11 0x21 0x11 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
chain[3]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
has freq in PIC, will disable freq setting.
chain[3] has freq in PIC and will jump over...
Chain[3] has core num in PIC
Chain[3] ASIC[1] has core num=1
Chain[3] ASIC[2] has core num=1
Chain[3] ASIC[3] has core num=1
Chain[3] ASIC[4] has core num=1
Chain[3] ASIC[5] has core num=1
Chain[3] ASIC[6] has core num=3
Chain[3] ASIC[7] has core num=1
Chain[3] ASIC[8] has core num=1
Chain[3] ASIC[9] has core num=1
Chain[3] ASIC[10] has core num=1
Chain[3] ASIC[11] has core num=1
Chain[3] ASIC[12] has core num=1
Chain[3] ASIC[13] has core num=1
Chain[3] ASIC[14] has core num=1
Chain[3] ASIC[15] has core num=1
Chain[3] ASIC[16] has core num=1
Chain[3] ASIC[17] has core num=1
has freq in PIC, will disable freq setting.
chain[8] has freq in PIC and will jump over...
Chain[8] has core num in PIC
Chain[8] ASIC[0] has core num=2
Chain[8] ASIC[2] has core num=1
Chain[8] ASIC[3] has core num=1
Chain[8] ASIC[4] has core num=1
Chain[8] ASIC[5] has core num=2
Chain[8] ASIC[6] has core num=1
Chain[8] ASIC[7] has core num=1
Chain[8] ASIC[8] has core num=1
Chain[8] ASIC[10] has core num=1
Chain[8] ASIC[11] has core num=1
Chain[8] ASIC[12] has core num=1
Chain[8] ASIC[13] has core num=1
Chain[8] ASIC[14] has core num=1
Chain[8] ASIC[15] has core num=1
Chain[8] ASIC[16] has core num=1
Chain[8] ASIC[17] has core num=1
has freq in PIC, will disable freq setting.
chain[9] has freq in PIC and will jump over...
Chain[9] has core num in PIC
Chain[9] ASIC[0] has core num=1
Chain[9] ASIC[1] has core num=1
Chain[9] ASIC[2] has core num=1
Chain[9] ASIC[3] has core num=1
Chain[9] ASIC[4] has core num=1
Chain[9] ASIC[5] has core num=1
Chain[9] ASIC[6] has core num=1
Chain[9] ASIC[7] has core num=1
Chain[9] ASIC[8] has core num=1
Chain[9] ASIC[9] has core num=1
Chain[9] ASIC[10] has core num=1
Chain[9] ASIC[11] has core num=1
Chain[9] ASIC[12] has core num=1
Chain[9] ASIC[13] has core num=1
Chain[9] ASIC[14] has core num=1
Chain[9] ASIC[15] has core num=1
Chain[9] ASIC[16] has core num=1
Chain[9] ASIC[17] has core num=1
has freq in PIC, will disable freq setting.
chain[10] has freq in PIC and will jump over...
Chain[10] has core num in PIC
Chain[10] ASIC[0] has core num=1
Chain[10] ASIC[1] has core num=1
Chain[10] ASIC[2] has core num=1
Chain[10] ASIC[3] has core num=1
Chain[10] ASIC[4] has core num=1
Chain[10] ASIC[5] has core num=1
Chain[10] ASIC[6] has core num=1
Chain[10] ASIC[9] has core num=1
Chain[10] ASIC[10] has core num=1
Chain[10] ASIC[11] has core num=1
Chain[10] ASIC[12] has core num=1
Chain[10] ASIC[13] has core num=1
Chain[10] ASIC[14] has core num=2
Chain[10] ASIC[16] has core num=2
Chain[10] ASIC[17] has core num=1
has freq in PIC, will disable freq setting.
chain[11] has freq in PIC and will jump over...
Chain[11] has core num in PIC
Chain[11] ASIC[0] has core num=1
Chain[11] ASIC[2] has core num=1
Chain[11] ASIC[4] has core num=3
Chain[11] ASIC[5] has core num=1
Chain[11] ASIC[6] has core num=1
Chain[11] ASIC[7] has core num=1
Chain[11] ASIC[8] has core num=1
Chain[11] ASIC[9] has core num=1
Chain[11] ASIC[10] has core num=1
Chain[11] ASIC[11] has core num=1
Chain[11] ASIC[12] has core num=1
Chain[11] ASIC[13] has core num=1
Chain[11] ASIC[15] has core num=1
Chain[11] ASIC[16] has core num=1
Chain[11] ASIC[17] has core num=1
has freq in PIC, will disable freq setting.
chain[12] has freq in PIC and will jump over...
Chain[12] has core num in PIC
Chain[12] ASIC[0] has core num=1
Chain[12] ASIC[1] has core num=1
Chain[12] ASIC[2] has core num=1
Chain[12] ASIC[3] has core num=1
Chain[12] ASIC[4] has core num=1
Chain[12] ASIC[5] has core num=1
Chain[12] ASIC[6] has core num=1
Chain[12] ASIC[7] has core num=1
Chain[12] ASIC[8] has core num=1
Chain[12] ASIC[11] has core num=1
Chain[12] ASIC[12] has core num=1
Chain[12] ASIC[13] has core num=1
Chain[12] ASIC[14] has core num=1
Chain[12] ASIC[15] has core num=1
Chain[12] ASIC[16] has core num=1
Chain[12] ASIC[17] has core num=1
has freq in PIC, will disable freq setting.
chain[13] has freq in PIC and will jump over...
Chain[13] has core num in PIC
Chain[13] ASIC[0] has core num=1
Chain[13] ASIC[1] has core num=1
Chain[13] ASIC[2] has core num=1
Chain[13] ASIC[3] has core num=1
Chain[13] ASIC[4] has core num=1
Chain[13] ASIC[5] has core num=1
Chain[13] ASIC[6] has core num=1
Chain[13] ASIC[8] has core num=1
Chain[13] ASIC[9] has core num=1
Chain[13] ASIC[10] has core num=1
Chain[13] ASIC[11] has core num=1
Chain[13] ASIC[12] has core num=1
Chain[13] ASIC[13] has core num=1
Chain[13] ASIC[14] has core num=2
Chain[13] ASIC[15] has core num=1
Chain[13] ASIC[16] has core num=1
Chain[13] ASIC[17] has core num=1
get PIC voltage=11 on chain[1], value=870
get PIC voltage=1 on chain[2], value=930
get PIC voltage=1 on chain[3], value=930
get PIC voltage=11 on chain[8], value=870
get PIC voltage=11 on chain[9], value=870
get PIC voltage=1 on chain[10], value=930
get PIC voltage=1 on chain[11], value=930
get PIC voltage=1 on chain[12], value=930
get PIC voltage=1 on chain[13], value=930
dsPIC33EP16GS202_pic_heart_beat failed on Chain[1]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[1]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[1]!
set_reset_allhashboard = 0x00000000
chain[8] temp offset record: -1,-1,-1,-1,-1,-1,-1,-1
chain[8] temp chip I2C addr=0x98
chain[10] temp offset record: -1,-1,-1,-1,-1,-1,-1,-1
chain[10] temp chip I2C addr=0x98
chain[12] temp offset record: -1,-1,-1,-1,-1,-1,-1,-1
chain[12] temp chip I2C addr=0x98
dsPIC33EP16GS202_pic_heart_beat failed on Chain[1]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[1]!
dsPIC33EP16GS202_pic_heart_beat failed on Chain[1]!
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
CRC error counter=0
set command mode to VIL

--- check asic number
After Get ASIC NUM CRC error counter=0
set_baud=0
The min freq=700
set real timeout 52, need sleep=379392
After TEST CRC error counter=0
search freq for 1 times, completed chain = 9, total chain num = 9
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
restart Miner chance num=2
waiting for receive_func to exit!
waiting for pic heart to exit!
bmminer not found= 1451 root       0:00 grep bmminer

bmminer not found, restart bmminer ...
This is user mode for mining
Detect 512MB control board of XILINX
Miner Type = T9+
Miner compile time: Fri Nov 24 23:19:16 EST 2017 type: Antminer T9+set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
set_reset_allhashboard = 0x0000ffff
miner ID : 80148c806f904814
set_reset_allhashboard = 0x0000ffff
dsPIC33EP16GS202_reset_pic failed on Chain[1]!
dsPIC33EP16GS202_reset_pic failed on Chain[1]!
dsPIC33EP16GS202_reset_pic failed on Chain[1]!
Checking fans!get fan[5] speed=5760
get fan[2] speed=6120
get fan[5] speed=5760
get fan[2] speed=6120
get fan[5] speed=5760
dsPIC33EP16GS202_reset_pic failed on Chain[1]!
dsPIC33EP16GS202_reset_pic failed on Chain[1]!
dsPIC33EP16GS202_reset_pic failed on Chain[1]!
chain[1] PIC jump to app
dsPIC33EP16GS202_jump_to_app_from_loader failed on Chain[1]!
dsPIC33EP16GS202_jump_to_app_from_loader failed on Chain[1]!
dsPIC33EP16GS202_jump_to_app_from_loader failed on Chain[1]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[1]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[1]!
dsPIC33EP16GS202_get_pic_sw_version failed on Chain[1]!
Check chain[1] PIC fw version=0xff
Chain[1] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x01 0x11 0x11 0x11 0x11 0x11 0x12 0x21 0x11 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x20 0x11 0x12 0x11 0x10 0x11 0x11 0x11 0x11 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
chain[1]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
Chain[J2] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J2] test patten OK temp=-1
chain[2] PIC jump to app
Check chain[2] PIC fw version=0x03
Chain[2] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x11 0x11 0x11 0x10 0x11 0x11 0x11 0x11 0x11 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x11 0x11 0x11 0x10 0x01 0x11 0x11 0x20 0x21 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x10 0x10 0x31 0x11 0x11 0x11 0x11 0x01 0x11 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
chain[2]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
Chain[J3] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J3] test patten OK temp=-1
chain[3] PIC jump to app
Check chain[3] PIC fw version=0x03
Chain[3] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x01 0x11 0x11 0x31 0x11 0x11 0x11 0x11 0x11 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x11 0x11 0x11 0x11 0x10 0x01 0x11 0x11 0x11 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x11 0x11 0x11 0x10 0x11 0x11 0x11 0x21 0x11 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
chain[3]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
Chain[J4] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J4] test patten OK temp=-1
Chain[J9] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J9] test patten OK temp=-1
Chain[J10] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J10] test patten OK temp=-1
Chain[J11] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J11] test patten OK temp=-1
Chain[J12] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J12] test patten OK temp=-1
Chain[J13] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J13] test patten OK temp=-1
Chain[J14] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J14] test patten OK temp=-1
Chain[J2] will use voltage=930 [1] to open core
set_Voltage_S9_plus_plus_BM1387_54 failed on Chain[1]!

set_Voltage_S9_plus_plus_BM1387_54 failed on Chain[1]!

set_Voltage_S9_plus_plus_BM1387_54 failed on Chain[1]!

Chain[J3] will use voltage=930 [1] to open core
Chain[J4] will use voltage=930 [1] to open core
Chain[J9] will use voltage=930 [1] to open core
Chain[J10] will use voltage=930 [1] to open core
Chain[J11] will use voltage=930 [1] to open core
Chain[J12] will use voltage=930 [1] to open core
Chain[J13] will use voltage=930 [1] to open core
Chain[J14] will use voltage=930 [1] to open core
Chain[J2] orignal chain_voltage_pic=11 value=870
Chain[J3] orignal chain_voltage_pic=1 value=930
Chain[J3] will use backup chain_voltage_pic=870 [11]
Chain[J3] get working chain_voltage_pic=11
Chain[J4] orignal chain_voltage_pic=1 value=930
Chain[J4] will use backup chain_voltage_pic=870 [11]
Chain[J4] get working chain_voltage_pic=11
Chain[J9] orignal chain_voltage_pic=11 value=870
Chain[J10] orignal chain_voltage_pic=11 value=870
Chain[J11] orignal chain_voltage_pic=1 value=930
Chain[J11] will use backup chain_voltage_pic=870 [11]
Chain[J11] get working chain_voltage_pic=11
Chain[J12] orignal chain_voltage_pic=1 value=930
Chain[J12] will use backup chain_voltage_pic=870 [11]
Chain[J12] get working chain_voltage_pic=11
Chain[J13] orignal chain_voltage_pic=1 value=930
Chain[J13] will use backup chain_voltage_pic=870 [11]
Chain[J13] get working chain_voltage_pic=11
Chain[J14] orignal chain_voltage_pic=1 value=930
Chain[J14] will use backup chain_voltage_pic=870 [11]
Chain[J14] get working chain_voltage_pic=11
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
T9+ try get asic num for the 1 time
Chain[J2] has 0 asic
set_reset_allhashboard = 0x0000ffff
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
set_reset_allhashboard = 0x00000000
T9+ try get asic num for the 2 time
Chain[J2] has 0 asic
set_reset_allhashboard = 0x0000ffff
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
set_reset_allhashboard = 0x00000000
T9+ try get asic num for the 3 time
Chain[J2] has 0 asic
set_reset_allhashboard = 0x0000ffff
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
set_reset_allhashboard = 0x00000000
T9+ try get asic num for the 4 time
Chain[J2] has 0 asic
set_reset_allhashboard = 0x0000ffff
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
set_reset_allhashboard = 0x00000000
T9+ try get asic num for the 5 time
Chain[J2] has 0 asic
set_reset_allhashboard = 0x0000ffff
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
dsPIC33EP16GS202_enable_pic_dc_dc failed on Chain[1]!
set_reset_allhashboard = 0x00000000
T9+ try get asic num for the 6 time
Chain[J2] has 0 asic
miner total rate=0GH/s fixed rate=0GH/s

Miner fix freq ...
max freq = 100
set baud=1
setStartTimePoint total_tv_start_sys=283 total_tv_end_sys=284
restartNum = 2 , auto-reinit enabled...
do read_temp_func once...
do check_asic_reg 0x08
Done check_asic_reg
set FAN speed according to: temp_highest=0 temp_top1[PWM_T]=0 temp_top1[TEMP_POS_LOCAL]=0 temp_change=0 fix_fan_steps=0
set full FAN speed...
FAN PWM: 100
read_temp_func Done!
CRC error counter=0
aramconde
newbie
Activity: 1
Merit: 0
Re: repair a T9 + after a bad firmware (lost chain)
April 25, 2019, 06:07:45 PM
#49
please can you make for me a video tutorial if your not busy and have time,i buy a old T9+ and 1 hashboard is not working and my hashrate is 7Th only,thank you in advance.
thierry4wd
sr. member
Activity: 446
Merit: 347
Re: repair a T9 + after a bad firmware (lost chain)
March 04, 2019, 03:58:59 PM
#48
Hi T9+ can not be overclocked without modification of Bmminer: s this one is blocked at 810mv audela of 675mhz of memory ... I compiled Bmminer for T9 + blocked at 840mv, and that allows me to go up to 750mhz for 13.65Ths with 1600w at Wall ...

The max overclock without bmminer modified is 12Th - 12.3Th at 1400w ...




Quote from: BitMaxz on March 03, 2019, 02:48:00 PM
There is a method that you can overclock antminer T9 miner to 14TH by editing the set_miner_conf.cgi through ssh.

Check it from here How To Overclock Your S9/T9+,T9,R4 To 18TH/s Free.

this method works well but is based on a software bug, I strongly don't recommend VERY strongly !!! the miner run VERY VERY VERY HOT !!! warning !!!!
MrCrank
sr. member
Activity: 1330
Merit: 258
Re: repair a T9 + after a bad firmware (lost chain)
March 04, 2019, 11:52:50 AM
#47
Where can download firmware source code?
I checked bitmain and can't found. I want modify it.
Thx.
BitMaxz
legendary
Activity: 3472
Merit: 3217
Playbet.io - Crypto Casino and Sportsbook
Re: repair a T9 + after a bad firmware (lost chain)
March 03, 2019, 02:48:00 PM
#46
Quote from: MrCrank on March 03, 2019, 11:19:59 AM
Do you have experience of overclocking upto 14TH?

There is a method that you can overclock antminer T9 miner to 14TH by editing the set_miner_conf.cgi through ssh.

Check it from here How To Overclock Your S9/T9+,T9,R4 To 18TH/s Free.
MrCrank
sr. member
Activity: 1330
Merit: 258
Re: repair a T9 + after a bad firmware (lost chain)
March 03, 2019, 11:19:59 AM
#45
Thanks for good job.
I have few T9+ and this is very useful information for me.
Do you have experience of overclocking upto 14TH?
philipma1957
legendary
Activity: 4326
Merit: 8950
'The right to privacy matters'
Re: repair a T9 + after a bad firmware (lost chain)
March 03, 2019, 08:43:30 AM
#44
Quote from: GreenDrago6972 on March 03, 2019, 07:59:25 AM
Is there another way to do this other then this method ?

buy a t9 board with proper flashing
GreenDrago6972
newbie
Activity: 1
Merit: 0
Re: repair a T9 + after a bad firmware (lost chain)
March 03, 2019, 07:59:25 AM
#43
Is there another way to do this other then this method ?
mikeywith
legendary
Activity: 2436
Merit: 6643
be constructive or S.T.F.U
Re: repair a T9 + after a bad firmware (lost chain)
January 21, 2019, 04:38:02 PM
#42
Quote from: ?? on ??
HOW CAN I DISMOUNT FIRMWARE DOLLEMIZER.
LOCK MY CONTROL BOARD S9.
DO NOT DELIVER IP AND DO NOT ACCEPT RE-INTALING OFFICIAL FIRMWARE BITMAIN.
THANK YOU

would you please stop using caps lock ?

why can't you load the original firmware back? what error do you get?

edit : lol just found out that i am not the only one disturbed by the caps lock.
HagssFIN
legendary
Activity: 2506
Merit: 1714
Electrical engineer. Mining since 2014.
Re: repair a T9 + after a bad firmware (lost chain)
January 21, 2019, 01:09:26 AM
#41
Quote from: ?? on ??
HOW CAN I DISMOUNT FIRMWARE DOLLEMIZER.
LOCK MY CONTROL BOARD S9.
DO NOT DELIVER IP AND DO NOT ACCEPT RE-INTALING OFFICIAL FIRMWARE BITMAIN.
THANK YOU

^You can try the IP Report button reset.

Instructions: https://support.bitmain.com/hc/en-us/articles/115003595387-How-to-reset-miner-to-factory-settings-

See chapter 3, "Restore via "IP Report" button".

Also, please don't overuse CAPS LOCK. IT LOOKS VERY STUPID.
thierry4wd
sr. member
Activity: 446
Merit: 347
Re: repair a T9 + after a bad firmware (lost chain)
January 17, 2019, 03:51:02 PM
#40
by force of working on the source I noticed an error,

in the source code to bmminer more problem, that I coriated, BUT, in the source code, for the T9 +, he verifies the verssion of the PIC, then ... against all odds, apply the update of the S9 !! ! to know :

Code:
// S9 , T9,  R4    PIC PROGRAM
#define PIC_PROGRAM "/etc/config/hash_s8_app.txt"

so there would be a solution to flash the card without pickit .... corrected this problem, but I have neither the temp nor the envi of brick again and restart my T9 +
Bill48105
jr. member
Activity: 48
Merit: 11
Re: repair a T9 + after a bad firmware (lost chain)
January 17, 2019, 11:42:23 AM
#39
Quote from: kano on December 29, 2018, 05:44:03 AM
I think the obvious point to make is don't put non-original firmware in your miners.
There are plenty of reasons why not to.

Generally speaking yes it's a bad idea to run non-original or unofficial firmware *except* in my case (and seems with others), downloading the source for the original/official miner from official bitmain github, building it per included instructions, then running it on T9+ essentially bricks the cards. One by one.. The longer you leave it running & auto-rebooting, the more cards it kills. It seems to happen if someone upgraded to the autotune firmware which must flash updates to the boards then the older software thinks the boards are corrupt so it tries to flash them & it appears to flash them wrong or with wrong version etc.  I didn't make note of what version of firmware these shipped with but if it wasn't the autotune one that's available on their site it's possible anyone flashing the pre-autotune firmware might end up in the same boat.
sahinkod
member
Activity: 119
Merit: 10
Re: repair a T9 + after a bad firmware (lost chain)
January 17, 2019, 07:22:52 AM
#38
please s9 hex file
kano
legendary
Activity: 4634
Merit: 1851
Linux since 1997 RedHat 4
Re: repair a T9 + after a bad firmware (lost chain)
December 29, 2018, 05:44:03 AM
#37
I think the obvious point to make is don't put non-original firmware in your miners.
There are plenty of reasons why not to.
mediann
newbie
Activity: 2
Merit: 0
Re: repair a T9 + after a bad firmware (lost chain)
December 28, 2018, 07:51:38 PM
#36
i just had success pickit the hashboards, some of them are working now great but some of them are showing to me like this

http://www.noelshack.com/2018-52-6-1546044666-t9-problem.png

Code:
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
Chain[J2] has 0 asic
Chain[J3] has 0 asic
Chain[J4] has 0 asic
Chain[J9] has 18 asic
Chain[J10] has 18 asic
Chain[J11] has 18 asic
Chain[J12] has 18 asic
Chain[J13] has 18 asic
Chain[J14] has 18 asic

Detect 1GB control board of XILINX
Miner Type = T9+
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x0000ffff
chain[1] PIC jump to app
Check chain[1] PIC fw version=0x03
chain[2] PIC jump to app
Check chain[2] PIC fw version=0x03
chain[3] PIC jump to app
Check chain[3] PIC fw version=0x03
Chain[J2] will use voltage=930 [1] to open core
Chain[J3] will use voltage=930 [1] to open core
Chain[J4] will use voltage=930 [1] to open core
Chain[J9] will use voltage=930 [1] to open core
Chain[J10] will use voltage=930 [1] to open core
Chain[J11] will use voltage=930 [1] to open core
Chain[J12] will use voltage=930 [1] to open core
Chain[J13] will use voltage=930 [1] to open core
Chain[J14] will use voltage=930 [1] to open core
Fix freq=400 Chain[1] voltage_pic=1 value=930
Fix freq=400 Chain[2] voltage_pic=1 value=930
Fix freq=400 Chain[3] voltage_pic=1 value=930
Fix freq=400 Chain[8] voltage_pic=1 value=930
Fix freq=400 Chain[9] voltage_pic=1 value=930
Fix freq=400 Chain[10] voltage_pic=1 value=930
Fix freq=400 Chain[11] voltage_pic=1 value=930
Fix freq=400 Chain[12] voltage_pic=1 value=930
Fix freq=400 Chain[13] voltage_pic=1 value=930
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
Chain[J2] has 0 asic
Chain[J3] has 0 asic
Chain[J4] has 0 asic
Chain[J9] has 18 asic
Chain[J10] has 18 asic
Chain[J11] has 18 asic
Chain[J12] has 18 asic
Chain[J13] has 18 asic
Chain[J14] has 18 asic
Chain[J9] has no freq in PIC, set default freq=400M
Chain[J9] has no core num in PIC
Chain[J10] has no freq in PIC, set default freq=400M
Chain[J10] has no core num in PIC
Chain[J11] has no freq in PIC, set default freq=400M
Chain[J11] has no core num in PIC
Chain[J12] has no freq in PIC, set default freq=400M
Chain[J12] has no core num in PIC
Chain[J13] has no freq in PIC, set default freq=400M
Chain[J13] has no core num in PIC
Chain[J14] has no freq in PIC, set default freq=400M
Chain[J14] has no core num in PIC

Miner fix freq ...
read PIC voltage=930 on chain[8]
Chain:8 chipnum=18
Asic[ 0]:400
Asic[ 1]:400 Asic[ 2]:400 Asic[ 3]:400 Asic[ 4]:400 Asic[ 5]:400 Asic[ 6]:400 Asic[ 7]:400 Asic[ 8]:400
Asic[ 9]:400 Asic[10]:400 Asic[11]:400 Asic[12]:400 Asic[13]:400 Asic[14]:400 Asic[15]:400 Asic[16]:400
Asic[17]:400
Chain:8 max freq=400
Chain:8 min freq=400

read PIC voltage=930 on chain[9]
Chain:9 chipnum=18
Asic[ 0]:400
Asic[ 1]:400 Asic[ 2]:400 Asic[ 3]:400 Asic[ 4]:400 Asic[ 5]:400 Asic[ 6]:400 Asic[ 7]:400 Asic[ 8]:400
Asic[ 9]:400 Asic[10]:400 Asic[11]:400 Asic[12]:400 Asic[13]:400 Asic[14]:400 Asic[15]:400 Asic[16]:400
Asic[17]:400
Chain:9 max freq=400
Chain:9 min freq=400

read PIC voltage=930 on chain[10]
Chain:10 chipnum=18
Asic[ 0]:400
Asic[ 1]:400 Asic[ 2]:400 Asic[ 3]:400 Asic[ 4]:400 Asic[ 5]:400 Asic[ 6]:400 Asic[ 7]:400 Asic[ 8]:400
Asic[ 9]:400 Asic[10]:400 Asic[11]:400 Asic[12]:400 Asic[13]:400 Asic[14]:400 Asic[15]:400 Asic[16]:400
Asic[17]:400
Chain:10 max freq=400
Chain:10 min freq=400

read PIC voltage=930 on chain[11]
Chain:11 chipnum=18
Asic[ 0]:400
Asic[ 1]:400 Asic[ 2]:400 Asic[ 3]:400 Asic[ 4]:400 Asic[ 5]:400 Asic[ 6]:400 Asic[ 7]:400 Asic[ 8]:400
Asic[ 9]:400 Asic[10]:400 Asic[11]:400 Asic[12]:400 Asic[13]:400 Asic[14]:400 Asic[15]:400 Asic[16]:400
Asic[17]:400
Chain:11 max freq=400
Chain:11 min freq=400

read PIC voltage=930 on chain[12]
Chain:12 chipnum=18
Asic[ 0]:400
Asic[ 1]:400 Asic[ 2]:400 Asic[ 3]:400 Asic[ 4]:400 Asic[ 5]:400 Asic[ 6]:400 Asic[ 7]:400 Asic[ 8]:400
Asic[ 9]:400 Asic[10]:400 Asic[11]:400 Asic[12]:400 Asic[13]:400 Asic[14]:400 Asic[15]:400 Asic[16]:400
Asic[17]:400
Chain:12 max freq=400
Chain:12 min freq=400

read PIC voltage=930 on chain[13]
Chain:13 chipnum=18
Asic[ 0]:400
Asic[ 1]:400 Asic[ 2]:400 Asic[ 3]:400 Asic[ 4]:400 Asic[ 5]:400 Asic[ 6]:400 Asic[ 7]:400 Asic[ 8]:400
Asic[ 9]:400 Asic[10]:400 Asic[11]:400 Asic[12]:400 Asic[13]:400 Asic[14]:400 Asic[15]:400 Asic[16]:400
Asic[17]:400
Chain:13 max freq=400
Chain:13 min freq=400

max freq = 400
set baud=4
Chain[J9] PIC temp offset=1,-7,0,0,0,0,33,28
Chain[J9] chip[0] use PIC middle temp offset=-7 typeID=55
New offset Chain[8] chip[0] local:27 remote:34 offset:23
Chain[J9] chip[0] get middle temp offset=23 typeID=55
Chain[J9] chip[128] use PIC middle temp offset=28 typeID=00
Warning: Chain[J9] has no temp offset in PIC! will fix it
New offset Chain[8] chip[0] local:27 remote:34 offset:23
Chain[J9] chip[0] get middle temp offset=23 typeID=55
New offset Chain[8] chip[32] local:-64 remote:0 offset:-42
Chain[J9] chip[32] get middle temp offset=-42 typeID=00
Chain[J11] PIC temp offset=1,-4,0,0,0,0,33,28
Chain[J11] chip[0] use PIC middle temp offset=-4 typeID=55
New offset Chain[10] chip[0] local:30 remote:34 offset:26
Chain[J11] chip[0] get middle temp offset=26 typeID=55
Chain[J11] chip[128] use PIC middle temp offset=28 typeID=00
Warning: Chain[J11] has no temp offset in PIC! will fix it
New offset Chain[10] chip[0] local:31 remote:34 offset:27
Chain[J11] chip[0] get middle temp offset=27 typeID=55
New offset Chain[10] chip[32] local:-64 remote:0 offset:-42
Chain[J11] chip[32] get middle temp offset=-42 typeID=00
Chain[J13] PIC temp offset=1,-5,0,0,0,0,33,28
Chain[J13] chip[0] use PIC middle temp offset=-5 typeID=55
New offset Chain[12] chip[0] local:25 remote:26 offset:29
Chain[J13] chip[0] get middle temp offset=29 typeID=55
Chain[J13] chip[128] use PIC middle temp offset=28 typeID=00
Warning: Chain[J13] has no temp offset in PIC! will fix it
New offset Chain[12] chip[0] local:25 remote:27 offset:28
Chain[J13] chip[0] get middle temp offset=28 typeID=55
New offset Chain[12] chip[32] local:-64 remote:0 offset:-42
Chain[J13] chip[32] get middle temp offset=-42 typeID=00
setStartTimePoint total_tv_start_sys=178 total_tv_end_sys=179
restartNum = 2 , auto-reinit enabled...
do read_temp_func once...
do check_asic_reg 0x08

get RT hashrate from Chain[8]: (asic index start from 1-18)

get RT hashrate from Chain[9]: (asic index start from 1-18)

get RT hashrate from Chain[10]: (asic index start from 1-18)

get RT hashrate from Chain[11]: (asic index start from 1-18)

get RT hashrate from Chain[12]: (asic index start from 1-18)

get RT hashrate from Chain[13]: (asic index start from 1-18)
Check Chain[J9] ASIC RT error: (asic index start from 1-18)
Check Chain[J10] ASIC RT error: (asic index start from 1-18)
Check Chain[J11] ASIC RT error: (asic index start from 1-18)
Check Chain[J12] ASIC RT error: (asic index start from 1-18)
Check Chain[J13] ASIC RT error: (asic index start from 1-18)
Check Chain[J14] ASIC RT error: (asic index start from 1-18)
Done check_asic_reg
do read temp on Chain[8]
Chain[8] Chip[1] TempTypeID=55 middle offset=23
read failed, old value: Chain[8] Chip[1] local Temp=0
read failed on Chain[8] Chip[1] middle Temp old value:0
Chain[8] Chip[9] TempTypeID=00 middle offset=-42
read failed, old value: Chain[8] Chip[9] local Temp=0
read failed on Chain[8] Chip[9] middle Temp old value:0
Done read temp on Chain[8]
do read temp on Chain[10]
Chain[10] Chip[1] TempTypeID=55 middle offset=27
read failed, old value: Chain[10] Chip[1] local Temp=0
read failed on Chain[10] Chip[1] middle Temp old value:0
Chain[10] Chip[9] TempTypeID=00 middle offset=-42
read failed, old value: Chain[10] Chip[9] local Temp=0
read failed on Chain[10] Chip[9] middle Temp old value:0
Done read temp on Chain[10]
do read temp on Chain[12]
Chain[12] Chip[1] TempTypeID=55 middle offset=28
read failed, old value: Chain[12] Chip[1] local Temp=0
read failed on Chain[12] Chip[1] middle Temp old value:0
Chain[12] Chip[9] TempTypeID=00 middle offset=-42
read failed, old value: Chain[12] Chip[9] local Temp=0
read failed on Chain[12] Chip[9] middle Temp old value:0
Done read temp on Chain[12]
set FAN speed according to: temp_highest=0 temp_top1[PWM_T]=0 temp_top1[TEMP_POS_LOCAL]=0 temp_change=0 fix_fan_steps=0
set full FAN speed...
FAN PWM: 100
read_temp_func Done!
CRC error counter=44
Pages:
Bitcoin Forum>Bitcoin>Mining>Mining support
Jump to: