Topic: RX 560 4GB Ethereum - page 31. (Read 212719 times)

Hi,

What is the memory type on this bios is hynix or micron?

Branko here's a screenshot of my strap timings...but i don't know which one to modify...could you suggest which one to copy and where? any help will be greatly appreciated....thanks

https://www.dropbox.com/s/4mwfx5xd0q9qn0p/s1.png?dl=0

I always modify 2000 strap only , because thats what I'm shooting at...that way if it fails, AMD drivers always go back to original 1750
strap safely ...Gigabyte doesn't have 2 sets of straps, but for cards that do, You have to change just one that is relevant for memory on card

hi Branko...what strap timing have your change? do you also have the 1:xxxx and 2:xxxx timing straps? mine is also hynix (HIS RX560 4GB OC)...don't know what setup will i change with it because my gpu always hangs up when i tried to modified most of the settings...thanks

My Gigabyte RX 560 hynix is doing 13.5 ETH / 350 decred...

Has anyone successfully configured MSI RX 560 Aero 4GB OC Edition (Hynix)? If so what are you getting for speeds for ETH?

i would be very surprised if a 460 with no pcie connector used more than 75 watts, even dual mining. 100 watts is WAY over the pcie spec.

60 watts for the just PC? seems kinda low unless you are using a "T" series intel proc, single ram stick and a m2 drive (and nothing else, including no fans).

my pc at idle uses 80-90 watts at the wall. g1840 proc, 2x4 gb ram, 390, 2x470, 460, 1070. 256 gb m2 ssd, 5 fans. evga 850 g2 gold psu pulling 750 at the wall mining only eth (dual mining pushed it to over 900 watts at the wall) (still need to tweak some stuff, hope to lower it a bit). all this on measured on a killowatt meter. 120 volts power.

it s maybe restricted to 75w but it use more
i have 5x rx460 4G msi with no pci-e power  and with dual mining the ring use 560w (no cpu load) with stock setting
so you can say each gpu use 100w

i just try to undervolt but cannot do much  it crash very fast with gpu at 1210mhz
i also change the traps to 1375 but cannot overclock the memory, i tested lot of traps, try to increase the memory more than 1750 it crash 
but even with memory at 1750 with 1375 trap it s 1.2 mh faster on eth @ 12.5 mh

If I'd be you, I'd surely be pissed about it, as AMD clearly states what is considered RX560:

http://www.amd.com/en/products/graphics/radeon-rx-560

so there should be no cards like yours

Not until you run gpu-z and check memory type (hynix, micron or samsung)

Hello Everyone,

Can anyone please share me the timing straps for MSI RX 560 Aero 4GB?

Any help please

No, 45W version is the one without external PCI-E connector, so
its restricted to draw max 75W (from board) while 90W one can use
max 150W (75W from motherboard and 75W from PCI-E 6-pin connector)


Radeon RX 560       Radeon RX 460    

Shaders     1024    vs    896    
Compute Units    16    vs    14    
TMUs        64    vs    56

But in previous post you said

"I bought 4 -NEW- Sapphire RX 460 unboxed from a sealed box... Sad  "


Whatever...460s have 14 CUs and 560s have 16 CUs...draw your conclusions form that fact

Strange then, that someone modified them at factory...still good rate, 3 out of 4
 460s transformed into 560s is OK in my book

But why did you say 560s in your original post?

Sounds like you bought modded RX460s, but mod didn't work well on one of cards

Thanks a lot...i will be waiting for that...i'll try to upload my gpu rom (the original one and the one that i modified) later when i got home. Again thanks for the time. I really appreciate it.

I will know more once my 4 560s come in and I can experiment with them to see what you are experiencing. The 570 I have now is not hooked t my Monitor and it was the normal routine - Backup bios. modify bios, reboot, run patcher, reboot, good to go. I know from everything I read for Hynix to use line 1500 in your timings. It pushed my 570 up pretty high. I am hoping to get 14+ with the 560s when they get here. Not sure what memory they will have the are Asus Rog Strix models 4GB models. Once I have them and play around i will be able to assist you better

thanks for the quick reply SummersideGuy...yeah i did run the patcher once...it worked only for one gpu...the one connected to the hdmi where i manage to get 11mH...and i tried to do it again but it just ask me to revert to the default driver/setting...

Did you run atikmdag-patcher-1.4.5 after you modded your bios. Also your card have Hyniz so you should use 1:1500 and 2:1500.      I have only played around with a 570 so far but it has Hynix 4GB same as yoru 560's and I have it to 28.3 vs 22 it was at stock. I have some 560s coming in next week so will know better then about those

Hi guys! I'm just new in crypto mining and started with a 4-GPU set for my rig. I don't have anything to pay you in exchange for a little help or reply but maybe somehow someone could share their knowledge concerning my setup, and it would be greatly appreciated.

My gpu is a HIS RX560 (Hynix) 4GB OC. I already tried to mod it one by one by copying the 1:1750 timing to 1:1875 to 2000 and 2:1750 all the way to 2:2200 and overclocked it core: 1250 and memory:2000 with +10 power. I managed to get 11.2mH/s in ETH claymore mining. I also tried other settings but that's the best i could get.

Here's my problem:
1.) whenever i plug-in the hdmi connector to the built-in (on-board) gpu...my mod setting in afterburner will not worked...everything is just 0...you cannot change the core, mem...everything...but all my 4 gpus were detected and it runs in its stock hashrate of 10mH.

2.)afterburner will only work if i connect the hdmi to one of the 4 gpu and then i could change the settings but only one gpu will only change in terms of hashrate, wherein i could get around 11.2mH while the other 3 gpu runs in its stock hashrate of 10mH.

any advice? what's wrong with my setup/mod? please could someone help me on this.

i will be posting my moddedROM if someone would like to test it.

thanks in advance!