Pages:
Author

Topic: TechnoBit Eastern Europe, BG HEX16A 7 GH/s/Плaтки имoнтaж нa Aвaлoн чип - page 13. (Read 92654 times)

legendary
Activity: 1610
Merit: 1000
I was keep getting "screen is terminating" when on cgminer screen under openwrt which restart cgminer. Any idea why since linux not my alley.
That is a bug in cgminer monitor script the screens when yo watch it are two o will post a fix later.
Just stop cron while you at watching it..then start it again
legendary
Activity: 1190
Merit: 1000
I was keep getting "screen is terminating" when on cgminer screen under openwrt which restart cgminer. Any idea why since linux not my alley.
legendary
Activity: 1190
Merit: 1000
newbie
Activity: 7
Merit: 0
where is possible to find driver for HEX16A under windows
pleaseeee.....
legendary
Activity: 1190
Merit: 1000
None of the chips are warm.

There is NO voltage over the capacitors (large one's).

12V lines seem OK.

The PIC gets 3.3V, the fan spins, no LEDs are lit ...

I am guessing the Firmware of the PIC is missing ...  Huh

The LED will lit when the HEX start hashing.

I faced the similar situation when 2 of my HEX16A arrived, 1 HEX hashing & other one not detected. Not detected HEX using 1,5 m long usb cable from external HDD which work just fine with HDD, other one use 50 cm long usb cable..
hero member
Activity: 728
Merit: 500
Ok,

I'll send them back.

Just to be clear i have to pay for the return costs?
NO
newbie
Activity: 55
Merit: 0
Ok,

I'll send them back.

Just to be clear i have to pay for the return costs?
hero member
Activity: 728
Merit: 500
None of the chips are warm.

There is NO voltage over the capacitors (large one's).

12V lines seem OK.

The PIC gets 3.3V, the fan spins, no LEDs are lit ...

I am guessing the Firmware of the PIC is missing ...  Huh
It seems there are a few customers with same problem.
Tested here OK and then no sign of USB device with the customer.
I'm getting one tomorrow to see what is the problem.
Please send these back .
I can send you back  on my account tomorrow Express ( UPS) 4 with terminal or in Thursday 4 with molex
hero member
Activity: 826
Merit: 1001
None of the chips are warm.

There is NO voltage over the capacitors (large one's).

12V lines seem OK.

The PIC gets 3.3V, the fan spins, no LEDs are lit ...

I am guessing the Firmware of the PIC is missing ...  Huh
Did you follow the 12V line from the power connector further on the board ?
newbie
Activity: 55
Merit: 0
None of the chips are warm.

There is NO voltage over the capacitors (large one's).

12V lines seem OK.

The PIC gets 3.3V, the fan spins, no LEDs are lit ...

I am guessing the Firmware of the PIC is missing ...  Huh
hero member
Activity: 826
Merit: 1001
im getting a bit depressed i expected the miners earlier, and now i have theme i cannot seem to get them to work.
- Is any of the chips on any of the four boards getting warm ?
- Try to locate the fuse(not sure if it has one) and check it with a multimeter.
- Measure the 12V at the power connector, follow the traces and keep on measuring until you don't measure 12V anymore. What component is between the last two measurement points ?
Make a high res picture of the loose smd part, upload it to one of the free picture sites and post a link here.

Good luck.
newbie
Activity: 55
Merit: 0
I received my miners today 4x HEX16A and one Nano Fury.

I tried connecting theme to windows 7 pc but non of the 4 miners are recognised as new device ...
I tried 4 different mini USB cables, i tested the mini usb cable with external HD and the HD worked.
I measured the voltage, 12VDC fans are spinning.
I tried connecting theme through USB hub (powered), direct to the USB port ... no difference.

I tried installing the drivers manualy, the serial port appears but says: device is not starting

I tried other windows 7 PC ... not recognised ...

I tried linux (raspi...) lsusb doesn't show new devices ...

Then i tried the nano fury , that worked right away ... (linux, windows,...)

I noticed that on one of the boards a smd component is not soldered on correctly ...

My order also included a TL-MR3020 this was not included ...
I asked molex connector and got terminals ...


The order dates back from: 2013-08-05 03:32:07!!! I finaly got them but they don't seem to work ...

I have several orders:
HEX16A 4x GNVJVDJUA
HEX16B: XZKTIHAQF
SHASH: BTUGUQKBB
Router: HPXZVIAHJ

im getting a bit depressed i expected the miners earlier, and now i have theme i cannot seem to get them to work.
legendary
Activity: 1190
Merit: 1000
Sorry We removed it  as an option as there were some power conflicts.
No chaining , just use USB HUB

I see, thanks  Smiley
hero member
Activity: 728
Merit: 500
Marto, since my board already here, then i want to ask about CAN chaining. Is it really not available or i need to solder some pin? I am willing to do it, just tell me what to do  Grin
Sorry We removed it  as an option as there were some power conflicts.
No chaining , just use USB HUB
newbie
Activity: 59
Merit: 0
items out of stock will be available again?
legendary
Activity: 1190
Merit: 1000
Marto, since my board already here, then i want to ask about CAN chaining. Is it really not available or i need to solder some pin? I am willing to do it, just tell me what to do  Grin
hero member
Activity: 728
Merit: 500
Again verry sorry for the inconvinience.
In the future for all sendings out of EU We'll use UPS or FEDEX

I prefer UPS  Grin

By the way is it ok to send the shipping cost to your btc address: 12DNdacCtUZ99qcP74FwchaCPzeDL9Voff  ?
OK
legendary
Activity: 1190
Merit: 1000
Again verry sorry for the inconvinience.
In the future for all sendings out of EU We'll use UPS or FEDEX

I prefer UPS  Grin

By the way is it ok to send the shipping cost to your btc address: 12DNdacCtUZ99qcP74FwchaCPzeDL9Voff  ?
hero member
Activity: 728
Merit: 500
Again verry sorry for the inconvinience.
In the future for all sendings out of EU We'll use UPS or FEDEX
Pages:
Jump to: